Maintenance Products

Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)

IC-LOC™ Red is a medium thickness, high strength thread lock that is applied to the threads of fasteners before assembly. Once the IC-LOC Red™ is cured, the fasteners are permanently together and cannot be disassembled. IC-LOC Red™ will maintain its strength up to 490° F. Uses

• Threads of fasteners
• Threads that need permanent bond

Directions: Shake well and then apply IC-LOC™ Red to the clean and dry threaded areas before assembling non- plastic parts. Product sets in 10 minutes, with full cure within 24 hours. IC-LOC™Red is anaerobic and cures in the absence of air, which occurs when a bolt, screw or nut is tightened. IC-LOC™ Red permanently prevents the loosening of threaded fasteners from shock and vibration, while sealing and preventing the rusting of threads. Cured temperature range is -60° to +300°F (-51° to +149°C).

Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!

Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

• Convenient pump spray (2oz.

IC-LOC™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-LOC™ Green wicks down into the threads of fasteners using capillary action and has good performance even with oil coated fasteners. Uses

• Threads of fasteners
• Bolts
• Screws
• Nuts

Directions: Shake well. Unscrew cap and cut off tip. Apply IC-LOC™ Green to clean preassembled fasteners. Product sets in 10 minutes, with full cure within 24 hours. IC-LOC™ Green prevents the loosening of threaded fasteners from shock and vibration by wicking into threads. Cured temperature range is -60° to +300°F (-51° to +149°C). Locked fasteners are only removable by localized heating and hand tools. Remove residue with a damp cloth. Similar to Loctite Green.

DeoxIT® D100L squeeze tube chemically improves metal to metal connections and contacts.100% solution, 2 ml,(Applications = 50 ± drops, 0.04 ml/drop).

DeoxIT® GOLD G100L (formerly ProGold), Squeeze Tube, 100% solution, 2 mL, (Applications = 50 ± drops, 0.04 ml/drop)

• Cleans and protects
• Easier playing
• Faster shredding

Cleans and protects all string materials, stops oxidation process, inhibits corrosion (rust) on phosphor-bronze, nickel, and stainless. Produces faster playing for easier shredding. Safe formula, will not harm fretboard surface. Safe for skin contact, non-allergenic, non-toxic and non-hazardous.

Lizard Spit two-step scratch and scuff remover.

• Biodegradable
• Made In USA

Includes:

• Step 1- Scratch and Scuff Remover
• Step 2- Scratch and Scuff Finisher

DeoxIT® cleaner and lubricant for conductive plastic faders and controls. Improves conductivity, maintains optimum signal quality, reduces wear and improves tactile feel - flushing action, safe on plastics. 2mL Squeeze Tube

Formula No. 65 Polish and Cleaner with a microfiber cloth! If you want to keep your guitar or bass clean as a whistle and looking as good as possible then Dunlop Formula No. 65 Guitar Polish and Cleaner should always be close at hand . And while you’re at it why not grab a nice microfiber cleaning cloth to go along with it? Formula No. 65 Polish and Cleaner removes wax build up, dirt, and grease while it polishes and protects the clear coat finish on your axe. This unique formulation will not build up making it perfect for musicians who clean their guitars after every use. Includes:

• (1) 4 oz. bottle of Dunlop Formula No. 65
• (1) microfiber cleaning cloth

4 oz. of cleaner that mixes with a gallon of water to prepare upholstery for use with S-CCOLORBOND-BLK. Successfully painting your leather or plastic requires careful paint prep and ColorBond's Prep Cleaner is one product you should have. A Liquid non-solvent, aqueous-based cleaner, Prep Cleaner removes dirt, grime and oil when readying surfaces for paint. Great for everything from leather to soft plastics, it's been engineered to remove compounds and releasing agents that typically spoil most paint jobs. When it's time for leather or plastic paint prep, ColorBond Prep Cleaner will leave you with a clean surface ready for paint. Recommended for use before the application of all ColorBond products.

Caig Flux Wash cleans and removes fluxes, light oils, and silicon.

• Safe on most plastics
• Evaporates quickly
• Removes wax and grease

Val-U Series Spray, adjustable valve, 5.5 oz.

Caig Heavy Duty Electronic Cleaner cleans electronic equipment and parts.

• 5.5 oz can
• Safe on Most Plastics
• Non-Corrosive
• Fast Drying, Zero Residue
• Non-Ozone Depleting
• VOC Complaint

Plastic-Cure™ is a gap-filling formulation of CA that works best on plastics. It is packaged in a bottle with a brush built into its top, which in many cases is an easier way to apply the CA. As long as brush is put back into the bottle after use, the bristles of the brush will not harden. Care must be taken, however, not to introduce foreign material into the bottle. The brush should not be used, for example, to apply CA to wood that has been freshly sanded. Plastic-Cure will also bond wood, but its brush applicator at times will not be the best way to apply it. Plastic-Cure is superior for the application of false nails and wraps on fingernails, where its brush is the preferred method of application. Uses

• Plastics
• Wood
• Foam
• False nails and wraps on fingernails

Directions: Carefully unscrew the cap.

Potentiometer cleaning caps for use with aerosol cleaners such as DeoxIT. This is a great tool for difficult to clean potentiometers such as those on hollow body guitars and certain amp chassis. The design pushes the spray in through the bushing of the potentiometer removing the need to access the back of the potentiometer. To use: Remove the knob and thread the cleaning cap onto the potentiometer. If there is enough bushing, attach the rubber o-ring first. If not, simply thread the cleaning cap onto the bushing and place a rag around it. Using a rag is recommended with and without the o-ring. Insert the DeoxIT straw into the small hole on the side of the cleaning cap. Cover the open end with your finger and spray. The cleaning solution is directed to the shaft of the pot where it can seep in. You can turn split shaft pots with a screwdriver through the open end to help move the cleaner around inside the pot.

Contact Cleaner Wash, Val-U Series Spray, adjustable valve, 5.5 oz., fast evaporating and safe on plastics.
Used for switches/relays, contacts/connectors, and parts/components.

Get rid of the gunk! If you want to keep your guitar or bass clean as a whistle and looking as good as possible then Dunlop Formula No. 65 Guitar Polish and Cleaner should always be close at hand! Formula No. 65 Polish and Cleaner removes wax build up, dirt, and grease while it polishes and protects the clear coat finish on your axe. This unique formulation will not build up making it perfect for musicians who clean their guitars after every use.

• 4 oz. spray bottle
• Polishes and protects
• Will not build up

Extend string life with Ultraglide 65!
Dunlop Ultraglide 65 String Cleaner and Conditioner is also known as “the squeak eliminator”. This is the #1 way to restore brilliance to your strings and increase string life. Ultraglide 65 conditions your strings with a silky smooth playing surface while shielding against tarnish and corrosion.

• Protects against corrosion and tarnish
• Increases string life
• 2 oz applicator bottle

Make your fretboard happy!
Keep fretboards clean and avoid cracking and drying by conditioning them with Dunlop Fretboard 65 Ultimate Lemon Oil.
Dunlop Fretboard 65 Ultimate Lemon Oil will remove grime and return your fretboard to it’s original luster quickly and easily. And once the dirt and grime are gone Fretboard 65 will keep it away by providing an invisible sealant against stains and moisture.
*Note* - Not for use on maple fretboards.

• Protects your fretboard from cracking and drying
• Moisturizes your fretboard
• Removes dirt, grime, and grease
• 4 oz. bottle

Type Z9, 1 fluid ounce. Silicone base, extra high-efficiency heat transfer. Made in USA. For mounting transistors, diodes, rectifiers, and resistors. Thermal joint compound for any device where efficient cooling is desired.

• For effective transfer of heat between components & heat sinks
• Will not dry or harden
• White paste

Grease-like consistency; opaque white in color; zero bleed; very stable at elevated temperatures; excellent thermal resistance and high thermal conductivity; efficient thermal coupler; effective and positive heat sink sealers and heat transfer agent. The product offers high thermal conductivity, virtually no bleed or evaporation over a wide operating temperature range. It will not harden, dry out or melt after 1,000 hours at 200°C. Meets Mil-C-47009 and Mil-C-47113.

Designed to polish all types of fret wire. Includes 24 × polish pads, 2 × fretboard guards, 1 × finishing cloth

Remove sticky, greasy messes with Goo Gone Original and return your surfaces to their original condition. Works on adhesive, crayon, gum, glue.

• Surface safe - formula will not harm your surfaces
• Removes tape - excellent for removing tape from your surfaces
• Perfect for cleaning - great for cleaning clothing, dinnerware and tables
• Removes stickers- great for removing stickers from gifts or even cars
• Use on - adhesive, gum, crayon, glue

Conductive Carbon Coating for most surfaces (rubber, epoxy, glass, plastic). It is ideal for repairing membrane buttons, keyboard buttons, and other carbon based surfaces. It may also be used as a coating for shielding (EMI) of electronics. Similar products on the market are more expensive, and have multiple containers requiring mixing prior to application. The CaiKote^TM 44 is applied in one step, allowed to dry and is ready for service.