Vacuum Tube Accessories

The YJShort is shorter than the standard YJS converter, allowing for use in amps that do not have room for the standard converters. It is a specialized, current-limiting/voltage-conditioning adapter for use in most 20 to 100 watt amps which use 6L6, EL34, 6550 or 6V6 output tubes

The YJUni is a simple pin-converting adapter for use in most amps with 6V6 or similar based tubes like 6F6, 6G6, 6K6, 6Y6, etc. The YJUni is shorter than standard Yellow Jacket® converters. It is designed for use in lower power output amps (20 watts or less) when no power reduction is desired.

The YJS is a specialized, current-limiting/voltage-conditioning adapter for use in most 20 to 100 watt amps that use 6L6, EL34, 6550 or 6V6 output tubes. The YJS is for amps with fixed bias power tubes. (Fixed bias tubes have their cathode connected directly to ground and a negative DC voltage applied to their control grid).

The YJC is a specialized, current-limiting/voltage-conditioning adapter for use in most 20 to 100 watt amps that use 6L6, EL34, 6550 or 6V6 output tubes. The YJC is for use in amps with cathode-biased power tubes.

Dual socket. 2 rows/12 lugs per row, 4 mounting holes. Board dimensions 5 ¼" x 3". Terminals are not pre-wired.

Single socket, 2 rows/6 lugs per row, 4 mounting holes. Board dimensions 3" x 3". Terminals are not pre-wired.

Includes:

• (1) T-7199-ADT
• (1) T-6GH8A

The YJR is a direct plug-in replacement adapter for use in most amplifiers that use 5AR4/GZ34, 5U4, 5Y3 or similar full-wave rectifier tubes. The YJR converts your amp's vacuum tube rectifier to a solid state rectifier, reducing tube sag for a tighter sound and feel.

This adapter allows you to use 6GH8A or 6U8A tubes in place of the difficult-to-find 7199. Tubes are not included.

Do you have valuable octal type tubes that work fine except the keyway has been broken off the base? Fix it with this simple and inexpensive product. Simply clean the remainder of the broken keyway from the base and slip one of these on. Will stay on by itself, or you can use a dab of silicon to attach if you wish.

8 pin socket saver with bracket. Commonly used in tube testers. Socket savers absorb the main wear and tear from many tube insertions and removals. It's much easier to replace a worn out socket saver than to replace the original socket.

15 x 15" egg crate packing box designed for storing tubes. Supplied unassembled. Each size is capable of holding a different number of tubes. For cartons see S-B127X

4-pin jumbo ceramic bayonet socket used for 211 and 845 tubes.

• Top mount
• 2-13/16" mounting centers
• Available with standard or gold plated pins

Solid State Rectifier Direct plug-in replacement for 5AR4, 5U4 and 5Y3 rectifier vacuum tubes in amplifiers with center tapped secondary power transformer. Use when less 'sag' is desired in the power supply; just switch back to the tube rectifier when 'sag' is desired.

8 pin octal socket saver. Commonly used in tube testers. Socket savers absorb the main wear and tear from many tube insertions and removals. It's much easier to replace a worn out socket saver than to replace the original socket.

Replacement foam tube stabilizer for Fender® Hot Rod Deluxe and Hot Rod Deville amps. This foam block slides over the first two preamp tubes. This genuine Fender® replacement is made in the USA.

8-pin premium ceramic tube socket commonly used for octal based power, preamp, and rectifier tubes. Can be top mounted or bottom mounted, using unique ring mount. Great replacement for Fender, Marshall and others.

• Premium quality
• Convenient top or bottom mount capabilities
• Includes mounting bracket
• 1-1/16” chassis hole required
• 1-7/16” oblong mounting centers

5-pin ceramic plate socket used for 807 tubes.

• Bottom mount
• 1" to 1 ¼" chassis hole required
• 1 ¾" mounting centers
• UY-Base, 5 Pins

7-pin ceramic plate socket used for 6C33B,829B and 3E29 sized tubes. Bossed mounting holes and recessed rivets allow sub-panel mounting .

• Bottom mount
• 1 ¼" chassis hole required
• 1-⅞" x 1-⅞" oblong mounting centers

8-pin phenolic tube socket commonly used for octal based power, preamp, and rectifier tubes.

• Top mount
• 1 3/16" to 1 ¼".chassis hole required
• 1-1/2” mounting centers

*Please Note: The S-H142 tube clip is not compatible with this socket.

7-pin ceramic plate socket used for 813 tubes. Bossed mounting holes and recessed rivets allow sub-panel mounting. Made in China

• Bottom mount
• 1 ¼" chassis hole required
• 1-⅞" x 1-⅞" oblong mounting centers

8-pin phenolic tube socket commonly used for octal based power, preamp, and rectifier tubes.

• Top mount
• 1” to 1-1/8” chassis hole required
• 1-1/2” mounting centers

7-pin ceramic plate socket used for 1625 tubes. Bossed mounting holes and recessed rivets allow sub-panel mounting .

• Bottom mount
• 1”- 1 ¼" chassis hole required
• 1-13/16” oblong mounting centers

Bottom mount ceramic socket has bossed mounting holes and recessed rivets to allow sub-panel mounting. Socket fits 300B, 811 size tubes.