Vacuum Tube Accessories

This adapter allows you to convert 6GH8A tubes to use instead of the hard to find 7199, 6GH8A not included.
Find the 6GH8A Tube Here

Includes:

• (1) T-7199-ADT
• (1) T-6GH8A

Washer fits around the socket in in order to hold it to the chassis. for 8 pin sockets.

Washer fits around sockets to hold them to chassis.

Cartons to hold tube egg crates S-B123, S-B124, S-B125, and S-B126. All sizes will fit the crates, but you may want additional vertical clearance for taller tubes. See S-B120X for the tube egg crate inserts

15 x 15" egg crate packing box designed for storing tubes. Supplied unassembled. Each size is capable of holding a different number of tubes. For cartons see S-B127X

Diameter listed is the inside diameter. The anode cap is used for making an electrical connection to vacuum tubes which have anode high voltage connection from the top. Its contact resistance is less than 0.01 ohm, insulation resisitance is over 10,000 Mohm. Life time is about 200 cycles.

Do you have valuable octal type tubes that work fine except the keyway has been broken off the base? Fix it with this simple and inexpensive product. Simply clean the remainder of the broken keyway from the base and slip one of these on. Will stay on by itself, or you can use a dab of silicon to attach if you wish.

When hole in chassis is too large to mount Type s sockets directly to chassis with wavy washer, this adapter can be used. 1 3/16" dia. opening in plate, 1 ½" to about 1 7/8" mounting centers can be used. Socket is secured to plate with wavy washer.

Black plastic 8-pin plug. This is the bottom portion of an octal tube base including all 8 pins and guide key between pins 1 and 8.

Retainer (Belton). for use with EL84 tubes, mounts to chassis. Steel plate with nickel plating and natural coil spring. Note: these retainers are for specialized socket below chassis mounting. (See mounting drawing below.) The springs are too short for standard sockets mounted level with the chassis surface.

For use with guitar amps and applications where tube is suspended upside down in chassis. Use with suspended 5881, 6L6 and EL34 tubes.

For use with guitar amps and applications where KT88/6550 is suspended upside down in the chassis.

Mounting Centers = 1", Overall Height = 2.2". Keeps common preamp tubes in place while dampening vibrations to reduce microphonics. Supports a maximum tube height of 2.1 inches

Tube retainer for EL84. for use with guitar amps and applications where the tube is suspended upside down in the chassis. Supports a maximum tube height of 2.8 inches

Rubber ring for retainer S-H141 fits EL34/5881 and 6L6GC tubes. Outer Diameter: 1.38" Inner Diameter: 1.00" Thickness: 0.16"

Rubber ring for retainer S-H143 fits KT88 and 6550 tubes. Dampens vibration.

Bottom mount ceramic socket has bossed mounting holes and recessed rivets to allow sub-panel mounting. Socket fits 300B, 811 size tubes.

4-pin ceramic bayonet socket used for 300B and 811 tubes.

• Top mount
• 2" mounting centers

4-pin ceramic tube socket.

• Bottom mount
• 1-1/4” chassis hole required
• 1-1/2” mounting centers

4-pin jumbo ceramic bayonet socket used for 211 and 845 tubes.

• Top mount
• 2-13/16" mounting centers
• Available with standard or gold plated pins

5-pin ceramic plate socket used for 807 tubes.

• Bottom mount
• 1" to 1 ¼" chassis hole required
• 1 ¾" mounting centers

7-pin ceramic plate socket used for 1625 tubes. Bossed mounting holes and recessed rivets allow sub-panel mounting .

• Bottom mount
• 1”- 1 ¼" chassis hole required
• 1-13/16” oblong mounting centers

7-pin ceramic plate socket used for 813 tubes. Bossed mounting holes and recessed rivets allow sub-panel mounting. Made in China

• Bottom mount
• 1 ¼" chassis hole required
• 1-⅞" x 1-⅞" oblong mounting centers