Vacuum Tube Accessories

P-STABLE Tube Stabilizer - Fender®, Hot Rod Series
Replacement foam tube stabilizer for Fender® Hot Rod Deluxe and Hot Rod Deville amps. This foam block slides over the first two preamp tubes. This genuine Fender® replacement is made in the USA.
$11.95
P-SP4-477 Tube Base - 4 pin replacement, 1.36" diameter
Replacement 4-pin tube base for use with tubes such as the 811A or 300B.
$4.95
P-SS9-162 Tube Shield - 9 Pin Miniature, 1-½" Tall with Bayonet Base
Made in China. Aluminum tube shield (with base), spring loaded, for short 9 pin miniature tubes like NOS 6386 with 1.50" seated height. (Too short to fit more common 9 pin miniature tubes like 12AX7 with 1.94" seated height).
$1.65
P-TB8-1-2 Terminal Board - one 8 Pin socket, 2 x 6 lugs
Single socket, 2 rows/6 lugs per row, 4 mounting holes. Board dimensions 3" x 3". Terminals are not pre-wired.
$18.95
P-SAYJUNI-X Tube Converter - Yellow Jacket® YJUni, for low-power amps
The YJUni is a simple pin-converting adapter for use in most amps with 6V6 or similar based tubes like 6F6, 6G6, 6K6, 6Y6, etc. The YJUni is shorter than standard Yellow Jacket® converters. It is designed for use in lower power output amps (20 watts or less) when no power reduction is desired.
$29.95
P-SP8-478 Tube Base - 8 Pin, Gold Coated Pins, 1.20" diameter
8 pin tube base with gold pins.
Outer Diameter: 1.20"
Inner Diameter: 1.16"
Height (not including pins or keyway): 0.79"
$4.55
SET-TV7-CALIBRATION Vacuum Tube Set - for calibrating TV-7 Testers
This is a set of measured vacuum tubes for use in TV-7 vacuum tube tester calibration. The values for each vacuum tube will be measured and included for the purpose of calibrating your own TV-7 tester at home. Steps for this calibration can be found online. Three tubes will be included:
  • 6L6
  • 6AU6
  • 12AT7

These tubes are tested at the following settings: Tube Filament Settings Bias Shunt Range 6L6 6.3 HS5-3481 23 0 D Tube Filament Settings Bias Shunt Range 6AU6 6.3 ET1-5672 16 0 B Tube Filament Settings Bias Shunt Range 12AT7 12.6 EV7-6080 10 0 C Note that brands are not guaranteed to match photograph.
$75.00
P-ST7-310 Socket - 7 Pin, Large, Ceramic Plate for 6C33C
7-pin ceramic plate socket used for 6C33B,829B and 3E29 sized tubes. Bossed mounting holes and recessed rivets allow sub-panel mounting .
  • Bottom mount
  • 1 ¼" chassis hole required
  • 1-⅞" x 1-⅞" oblong mounting centers
$5.55
P-ST7-813 Socket - 7 Pin, Large, Ceramic for 813, Chinese
7-pin ceramic plate socket used for 813 tubes. Bossed mounting holes and recessed rivets allow sub-panel mounting. Made in China
  • Bottom mount
  • 1 ¼" chassis hole required
  • 1-⅞" x 1-⅞" oblong mounting centers
$5.30
P-ST9-AWS-C Socket - 9 Pin, Ceramic, for Auto-Wave Soldering
9-pin ceramic tube socket for auto-wave soldering applications.
Measurements:
  • Center PCB hole diameter -0.73"
  • Mounting pin diameters - (9 holes at 1.00") and (3 holes at 1.26")
$3.30
P-SP8-477 Tube Base - 8 Pin, Gold Coated Pins, 1.57" diameter
8 pin tube base with gold coated pins.
Outer Diameter: 1.57"
Inner Diameter: 1.52"
Height (not including pins or keyway): 0.80"
$4.30
Don't see what you're looking for? Send us your product suggestions!