Vacuum Tube Accessories

8-pin ceramic tube socket commonly used for octal based power, preamp, and rectifier tubes. Can be top mounted or bottom mounted, using unique ring mount. Great replacement for Fender, Marshall and others.

• Convenient top or bottom mount capabilities
• Includes mounting bracket
• 1-1/16” to 1-1/8” chassis hole required
• 1-7/16” oblong mounting centers

8-pin plastic tube socket commonly used for octal based power, preamp, and rectifier tubes.

• 1-1/8” / 1.14” chassis hole required
• Snap-in Mounting

*Uses P-SH12-1-31 or P-SH2-104-2

9-pin ceramic tube socket with center shield commonly used for preamp tubes or EL84 power tubes

• Top mount
• 3/4” chassis hole required
• 1-1/8” mounting centers

8-pin plastic tube socket commonly used for octal based power, preamp, and rectifier tubes.

• Bottom mount
• Includes mounting bracket
• 1” chassis hole required
• 1 ¼" mounting centers

This adapter allows you to convert 6GH8A tubes to use instead of the hard to find 7199, 6GH8A not included.
Find the 6GH8A Tube Here

Diameter listed is the inside diameter. The anode cap is used for making an electrical connection to vacuum tubes which have anode high voltage connection from the top. Its contact resistance is less than 0.01 ohm, insulation resisitance is over 10,000 Mohm. Life time is about 200 cycles.

9-pin tube socket commonly used for preamp tubes or EL84 power tubes

• Bottom mount
• 1-15/16” shield height
• 25/32”/ .76” chassis hole required
• 1-1/8” mounting centers

Assortment of metal 'stand off' spacers. 20 pieces.

5-pin ceramic plate socket used for 807 tubes.

• Bottom mount
• 1" to 1 ¼" chassis hole required
• 1 ¾" mounting centers

9-pin plastic tube socket commonly used for preamp tubes or EL84 power tubes

• PC mount
• ¾” chassis hole required (bottom mount)
• 3/4” tail diameter

8 pin octal tube base, brown.
Inside Diameter = 1 3/16"
Height = 7/8"

9-pin ceramic tube socket commonly used for preamp tubes or EL84 power tubes

• Bottom, PC mount
• ¾” chassis hole required
• ¾” tail diameter
• Available with standard or gold pins

8-pin phenolic tube socket commonly used for octal based power, preamp, and rectifier tubes.

• Top mount
• 1 3/16" to 1 ¼".chassis hole required
• 1-1/2” mounting centers

*Please Note: The S-H142 tube clip is not compatible with this socket.

9-pin ceramic tube socket with attached shield base commonly used for preamp tubes or EL84 power tubes (without shield)

• Top mount
• 7/8” chassis hole required
• 1-1/8” mounting centers
• P-SS9-325 and P-SS9-325XL are compatible tube shields.

7-pin ceramic plate socket used for 1625 tubes. Bossed mounting holes and recessed rivets allow sub-panel mounting .

• Bottom mount
• 1”- 1 ¼" chassis hole required
• 1-13/16” oblong mounting centers

9-pin ceramic tube socket with gold pins commonly used for preamp tubes or EL84 power tubes

• PC mount
• 7/8” tail diameter
• Gold pins

When hole in chassis is too large to mount Type s sockets directly to chassis with wavy washer, this adapter can be used. 1 3/16" dia. opening in plate, 1 ½" to about 1 7/8" mounting centers can be used. Socket is secured to plate with wavy washer.

8-pin premium ceramic tube socket commonly used for octal based power, preamp, and rectifier tubes. Can be top mounted or bottom mounted, using unique ring mount. Great replacement for Fender, Marshall and others.

• Premium quality
• Convenient top or bottom mount capabilities
• Includes mounting bracket
• 1-1/16” chassis hole required
• 1-7/16” oblong mounting centers

9-pin ceramic tube socket with stand-off mounting. commonly used for preamp tubes or EL84 power tubes.

• Standoff, PC mount
• 0.822” outer diameter
• 3/4” tail diameter

Dual socket. 3 rows/10 lugs per row, 4 mounting holes. Board dimensions 5 ½" x 3 ¾". Terminals are not pre-wired.

9-pin ceramic PC mount tube socket commonly used for preamp tubes or EL84 power tubes

• Standoff, PC mount
• 0.70” outer diameter
• 3/4” tail diameter

7-pin ceramic plate socket used for 6C33B,829B and 3E29 sized tubes. Bossed mounting holes and recessed rivets allow sub-panel mounting .

• Bottom mount
• 1 ¼" chassis hole required
• 1-⅞" x 1-⅞" oblong mounting centers

Ceramic Tube socket used for octal power tubes, PC mount

• Chassis hole: 1” to 1-1/4” depending on mounting (Top: 1” to 1-1/8”, Bottom: 1-1/4”)
• Mounting Centers: 1-1/2” with oblong mounting holes
• PC mount pins