Vacuum Tube Accessories

P-SG11X Grid / Plate Anode Cap - Ceramic for tubes
Diameter listed is the inside diameter. The anode cap is used for making an electrical connection to vacuum tubes which have anode high voltage connection from the top. Its contact resistance is less than 0.01 ohm, insulation resisitance is over 10,000 Mohm. Life time is about 200 cycles.
Starting at $1.15
P-STX-CVR Covers - for Chassis Socket Hole, Steel
Steel plates for covering unused socket holes on modified chassis. These covers provide a safe solution for modifying any chassis. These covers use elongated mounting holes to fit a variety of socket hole sizes. P-ST9-CVR
  • 9 pin (noval) socket hole cover
  • 5mm x 3.5mm mounting holes
  • 27.1mm center to center

P-ST8-CVR
  • 8 pin (octal) socket hole cover
  • 6.5mm x 3.5mm mounting holes
  • 40mm center to center

P-ST8-ST9-CNVRT
  • 8 pin to 9 pin (octal to noval) socket adapter
  • Bottom mount 9 pin socket recommended
$2.75
P-ST8-210M Socket - 8 Pin, 1" Chassis Hole, 1-¼" Mounting Centers
8-pin plastic tube socket commonly used for octal based power, preamp, and rectifier tubes.
  • Bottom mount
  • Includes mounting bracket
  • 1” chassis hole required
  • 1 ¼" mounting centers
$4.06
P-ST9-213 Socket - 9 Pin, Miniature, with Shielded Base
9-pin phenolic tube socket with attached shield base.
  • Top mount
  • 3/4” chassis hole required
  • 1-1/8” mounting centers

Please Note: Tube retainer S-H144 will not work with this socket
$2.19
S-H143 Retainer - Fits KT88 / 6550 Size Tubes
For use with guitar amps and applications where KT88/6550 is suspended upside down in the chassis.
$2.75
P-ST7-816 Socket - 7 Pin, Miniature, Ceramic, with Aluminum Shield
7-pin tube socket commonly used for preamp tubes. Shield Included.
  • Top mount
  • 1-7/8” shield height
  • 5/8” chassis hole required
  • 7/8” mounting centers
  • Includes Shield
$1.13
S-H146 Vacuum Tube Retainer - for 12AX7 Tubes
Mounting Centers = 1", Overall Height = 2.2". Keeps common preamp tubes in place while dampening vibrations to reduce microphonics. Supports a maximum tube height of 2.1 inches
$2.42
P-ST8-500 Socket - 8 Pin, Phenolic, MIP, top mount
8-pin phenolic tube socket commonly used for octal based power, preamp, and rectifier tubes.
  • Top mount
  • 1 3/16" to 1 ¼".chassis hole required
  • 1-1/2” mounting centers

*Please Note: The S-H142 tube clip is not compatible with this socket.
$4.94
On Backorder
P-ST8-250MT Socket - 8 Pin Octal, Saddle Plate, Black, Top Mount
8-pin plastic tube socket commonly used for octal based power, preamp, and rectifier tubes.
  • Top mount
  • 1-1/16” chassis hole required
  • 1 ½" mounting centers
$3.69
P-ST9-224 Socket - 9 Pin, PC Mount, Black Plastic
9-pin plastic tube socket commonly used for preamp tubes or EL84 power tubes
  • PC mount
  • ¾” chassis hole required (bottom mount)
  • 3/4” tail diameter
$1.39
P-ST9-900 Socket Saver - 9 Pin Miniature, for reducing wear and tear
9 pin miniature socket saver. Commonly used in tube testers. Socket savers absorb the main wear and tear from many tube insertions and removals. It's much easier to replace a worn out socket saver than to replace the original socket.
$4.06
P-SS9-325XL Tube Shield - For 9-Pin, Aluminum, Extra Long
Extra long (70mm) aluminum tube shield for noval tubes. Ideal for tubes that are longer than a standard preamp tube such as the 6CG7, 12BH7, etc.
  • Includes shield base
  • Designed for longer than standard pre-amp tubes
  • Sold individually
  • Compatible with P-ST9-212
$1.55
P-ST8-801 Socket - 8 Pin Octal, Ceramic, with Separate Retaining Ring
8-pin ceramic tube socket commonly used for octal based power, preamp, and rectifier tubes. Great replacement for Fender, Marshall and others.
  • Convenient top or bottom mount capabilities
  • Includes mounting bracket
  • Spade type pins
  • 1-1/16” to 1-1/8” chassis hole required
  • 1-7/16” oblong mounting centers
$1.95
S-H143-RING Ring for Retainer - rubber, fits KT88 and 6550 Tubes
Rubber ring for retainer S-H143 fits KT88 and 6550 tubes. Dampens vibration.
$0.68
P-ST8-1000 Socket Saver - 8-Pin, for reducing wear and tear on tube sockets
8 pin octal socket saver. Commonly used in tube testers. Socket savers absorb the main wear and tear from many tube insertions and removals. It's much easier to replace a worn out socket saver than to replace the original socket.
$9.95
T-SSR01 Solid State Rectifier - For 5AR4, 5U4, 5Y3 Tubes
Solid State Rectifier Direct plug-in replacement for 5AR4, 5U4 and 5Y3 rectifier vacuum tubes in amplifiers with center tapped secondary power transformer. Use when less 'sag' is desired in the power supply; just switch back to the tube rectifier when 'sag' is desired.
$9.95
P-SS9-325-X Tube shield - for 9-pin miniature, aluminum, multiple colors
Colors Available:
Protect your preamp tubes and customize them to suit your style with these colorful aluminum tube shields.
Starting at $1.18
P-ST9-223 Socket - 9 Pin, Standoff Ceramic PC Mount
9-pin ceramic tube socket with stand-off mounting. commonly used for preamp tubes or EL84 power tubes.
  • Standoff, PC mount
  • 0.822” outer diameter
  • 3/4” tail diameter
$2.19
P-ST9-610 Socket - 9 Pin, ¾" mounting hole, top mount
9-pin Micalex tube socket commonly used for preamp tubes or EL84 power tubes. Applicable for use with all types of electronic equipment using vacuum tubes.
  • Top mount
  • 3/4” chassis hole required
  • 1” mounting centers
$3.69
S-H145 Vacuum Tube Retainer - Belton, for EL84s, High Quality
Retainer (Belton). for use with EL84 tubes, mounts to chassis. Steel plate with nickel plating and natural coil spring. Note: these retainers are for specialized socket below chassis mounting. (See mounting drawing below.) The springs are too short for standard sockets mounted level with the chassis surface.
$1.95
P-SS9-600 Tube Shield - Belton, Push Twist for Socket P-ST9-AWS
2" tall, for use with P-ST9-AWS. Push/twist to chassis, no mounting centers. Belton manufacture. Aluminum sleeve with natural coil spring. Spring length: 26mm
$2.75
P-YJR Solid State Rectifier - Yellow Jacket® YJR, For 5AR4, 5U4, 5Y3
The YJR is a direct plug-in replacement adapter for use in most amplifiers that use 5AR4/GZ34, 5U4, 5Y3 or similar full-wave rectifier tubes. The YJR converts your amp's vacuum tube rectifier to a solid state rectifier, reducing tube sag for a tighter sound and feel. The tube rectifier can easily be swapped back in when sag is desired. This Yellow Jacket® is a solid state device and as such does not come with vacuum tubes.
  • Converts most audio amplifiers which use a vacuum tube rectifier 5AR4/GZ34, 5U4 or 5Y3 to a solid state device.
  • Safe for all common amplifiers and transformers.

All Yellow Jacket® converters have a one year warranty against manufacturer defects.
$14.95
P-ST4-194 Socket - 4 Pin, Ceramic, Chassis Mount
4-pin ceramic tube socket.
  • Bottom mount
  • 1-1/4” chassis hole required
  • 1-1/2” mounting centers
$3.13
P-ST9-400 Socket - 9 Pin, Miniature, Ceramic, Chassis Mount
9-pin tube socket commonly used for preamp tubes or EL84 power tubes
  • Bottom mount
  • 1-15/16” shield height
  • 25/32”/ .76” chassis hole required
  • 1-1/8” mounting centers
$1.56
Don't see what you're looking for? Send us your product suggestions!