Transformers & Chokes

P-H1600-A Switch - Rotary Impedance Selector, for Hammond 1600A series
Includes: 3 pole, 3 position rotary switch, ¼" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with ¼" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and ¼" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G) (See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
$11.95
P-RC-1 Choke - One Electron, Audio, PRC-1, for Shunt Feed SE Output
The PRC-1 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.
$85.00
P-RC-2 Choke - One Electron, Audio, PRC-2, for Shunt Feed SE Output
The PRC-2 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.
$69.95
P-RC-3 Choke - One Electron, Audio, PRC-3, 225H for Preamp Output
The PRC-3 audio choke from One Electron was designed as a plate load for the output of either a high quality line amplifier or a phono preamp.
$69.95
P-T118944 Transformer - Hammond, Radiola III-A Replacement Audio
Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features
  • Primary: 4000 turns, #41 wire (lugs 4 & 2)
  • Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
  • Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
  • Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
  • Lamination Core Size: 5/8" x 1/2"
  • Weight: 7 oz.
$48.25
P-T125H Transformer - Hammond, Output, 8 W, 10k Primary
Specifications Audio Watts: 8 watts Primary Impendance (Ohms): 10K center-tapped Secondary Impendance (Ohms): 2/4/8 Mounting centers: 2-3/8u-bracket Weight: 1.0 lbs. Cat. No. Dimensions (Inches) A B C D G Mtg. Hole 125H 2.81 1.4 1.7 2.36 0.187
$37.00
P-T125J Transformer - Hammond, Output, 8 W, 2.5k or 4k Primary
Specifications Audio Watts: 8 Primary Impendance (Ohms): 2.5k/4K center-tapped Secondary Impendance (Ohms): 6/8 - 3.2/4 Mounting centers: 2-13/16u-bracket Weight: 1.0 lb.
$36.99
P-T125X Transformer - Hammond, Universal Push-Pull
  • Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
  • Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
  • Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
  • Tables provided with transformer listing 90 pre-calculated impedance ratios.
Starting at $36.82
P-T125XSE Transformer - Hammond, Universal Single Ended
  • Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits.
  • Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE).
  • For push-pull output use, see P-T125A - optimized for push-pull tube output circuits.
  • Open style with minimum 12" long primary & secondary leads leads.
  • All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C. core saturation.
  • Primary impedance range from 2,500 to 10,000 Ohms.
  • Secondary impedance range from 4 to 32 Ohms.



Part No.
Audio Power
Max D.C. Bias
Dimensions (Inches)


A
B
C
D
E
G Mtg.
Starting at $45.84
P-T162XSEA Transformer - Hammond, Output, Single-Ended, 30 W
  • Over designed for single ended tube output circuits (triode, tetrode or pentode tubes).
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response at least 20 Hz. to 20 Khz. at full rated power (± 1 db max. ref.
$159.23
P-T1650X Transformer - Hammond, Tube Output, Push-Pull
  • Designed for push-pull tube output circuits.
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Starting at $85.25
P-T1650XA Transformer - Hammond, Tube Output, Easy Wire Secondary
  • Designed for push-pull tube output circuits.
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Starting at $96.51
P-T1750ORF Transformer - Hammond, Output, replacement for Orange Rocker 30
Hammond output transformer - replacement for Orange Rocker 30 Specifications: Part No. Pri Ohms Sec Ohms Amplifier Type Watts Bobbin/Paper Winding Equivalent To P-T1750ORF 6,000 C.T. 8, 16 Push-Pull 35 W Bobbin OT199SL
$58.50
P-T1750X-FENDER Transformer - Hammond, Output, replacement for Fender
  • Replacements for Fender Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $18.44
P-T1750X-MARSHALL Transformer - Hammond, Output, replacement for Marshall
  • Replacements for Marshall Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $37.50
P-T1750X-VOX Transformer - Hammond, Output, replacement for Vox
  • Replacements for Vox Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $95.44
P-T1750X-YORKVILLE Transformer - Hammond, Output, replacement for Yorkville / Traynor
  • Replacements for Yorkville/Traynor Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $43.43
P-T290-MARSHALL Transformer - Hammond, Guitar Amplifier, replacement for Marshall
  • Replacements for Marshall amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $96.50
P-T290-VOX Transformer - Hammond, Guitar Amplifier, replacement for Vox
  • Replacement for Vox amplifiers
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $72.95
P-T290-YORKVILLE Transformer - Hammond, Guitar Amplifier, replacement for Yorkville / Traynor
  • Replacement for Yorkville/Traynor amplifiers
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Part No. Primary Secondary 1 Secondary 2 Secondary 3 Yorkville / Traynor Amp Yorkville / Traynor Part No VAC Hz. P-T290TRA 120 V 60 Hz. 320 V @ 600 mA 60 V @ 50 mA 6.3 V.C.T. @ 9 A 100 Watt Bass A-1380 P-T290TRB 120 V 60 Hz. 620 V @ 115 mA 6.3 V.C.T. @ 115 mA YBA2-B A-1314 P-T291JX 120 V 60 Hz. 320 V @ 500 mA 60 V @ 20 mA 6.65 V.C.T.
Starting at $76.50
P-T291 Transformer - Output, 8 W, 4kΩ - 9kΩ impedance
Specifications Output 8 W Primary Impedance 4,000 to 9,000 Ω Mounting Centers 2.375" Weight 0.7 lbs
$21.39
P-T31 Transformer - Output, 8 W, Single Ended
Specifications
  • Power: 8 W
  • Primary Impedance: 5,000 Ω single-ended
  • Secondary Impedance: 8 Ω
  • Primary DC Resistance (Red to Blue): 230 Ω
  • Mounting Centers: 2.375"
  • Mounting Type: U-bracket
  • Weight: 0.7 lbs
$15.50
P-TF22848-X Transformer - Fender® Replacement, Output, 35 W
Replacement for Pro Reverb, Tremolux, Vibrolux, Bandmaster, and Vibroverb. Equivalent to #125A6A & #022848.
Starting at $43.00
P-TF22871 Transformer - Fender® Replacement, Output, 50 W, 4 Ohm
Replacement for Bassman heads. Equivalent to #125A13A & #022871.
$69.95
Don't see what you're looking for? Send us your product suggestions!