Transformers & Chokes

Power transformer replacement for the Fender® part number 64526 as used in the 5E3 Deluxe Amp. This transformer accounts for modern mains voltage and will provide a B+ voltage of ~370VDC with 120VAC on the primary in a standard 5E3 build paired with the P-TGO-002 output transformer. This upgraded transformer also features a center tap on the 6.3V filament. Features

• Provides vintage correct DC voltages in stock 5E3 builds
• 330V (660 VCT) B+ at 120mA
• Center tapped 6.3V filament at 2A
• 5V filament supply at 2A
• For 120V 60Hz primary
• Standard 2.8125" x 2.25” mounting centers

• Primary 115VAC, 50 / 60 Hz., Secondary 115VAC
• Provides complete circuit isolation.
• Electrostatic shield between primary & secondary to greatly attenuate surges and noise.
• Hi-pot tested to 2 KV RMS.
• Circuit breaker in primary.
• Standard 3-wire, grounded plug & receptacle.
• Input (primary) connected to 5 foot long cord & standard North American plug (NEMA 5-15P).
• Output (secondary) connected to 1 foot long "pig tail" cord, 3-wire, standard North American grounded receptacle (NEMA 5-15R).
• North American Mark of Safety - C UL & UL listed (File #E211544)
• Indoor use only
• Remember - These units do NOT convert line frequency

Open style, chassis mount transformers with a 115V 60Hz primary and an 80V center tapped secondary.

• Primary 115 VAC, 50 / 60 Hz.
• At 2,000 VAC and above, secondary leads are through rubber bushings
• Units can be run full wave bridge or full wave C.T.
• V.A. is a C.C.S. rating
• Current ratings are CCS (Continuous Commercial Service) & ICAS ratings (Intermittent Commercial or Amateur Service).
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Class A insulation (105 degrees C).
• Hi-Pot test at a minimum of twice secondary voltage
• Conservative designs - CSA certified (209651).

• Replacement for Vox amplifiers
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Dual 117/234 VAC primary, 50/60 Hz. operation. 24 V series, 12 V parallel secondary.

Secondary VAC: 10V C.T.
Current: 5 A
VA Rating: 50
Features:

• Single Primary 115VAC
• Operates on 50/60 Hz.
• Combination solder or quick connect terminals.
• Split bobbin construction eliminates the need for an electrostatic shield.
• Hi-pot tested to 2 KV RMS.
• Economical open style, channel frame - chassis mount design
• UL recognized & CSA certified.

Open style, chassis mount transformers with a 117V 50/60Hz primary and a 12V secondary.

Primary 115 VAC 60 Hz.
Secondary DC current measured with cap. input filter, full wave (two diode) C.T., rectifier circuit.
Enclosed, 4 hole chassis mount.
Minimum 6 long leads.
2" X 2" vertical mounting centers.
Class A insulation (105 degrees C).
Hi-Pot test of 2000 V RMS.
Conservative designs - CSA certified (# LR3902).
3.2lbs
Secondary: 250-0-250 V100 mA
Filament winding 1: 5 V2 A
Filament winding 2: 6.3 V3 A

Open style, chassis mount transformers with a 115V 60Hz primary and a 120V center tapped secondary.

• Both series operate on 50/60 Hz current
• Low profile, split bobbin design.
• Dual winding secondaries, non-concentrically wound
• Units are designed so that all windings must be used
• Low primary to secondary coupling - no electrostatic shield required.
• High insulation - Hipot of 2,500V RMS.
• Class B insulation - 130 degrees C.
• c UL us recognized

• Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
  
  • NOTE: units are designed to operate with BOTH primary windings engaged.
  • See primary wiring information under resources.
• Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
• Highpot tested: 2,000 VAC
• Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
• Windings: Concentric wound for low stray field and low noise.
• Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
• Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
• Conservative designs - CSA certified (209651).

Dual 117/234 VAC primary, 50/60 Hz. operation. 36 V series, 18 V parallel secondary.

Secondary VAC: 12.6V C.T.
Current: 4 A
VA Rating: 50.4
Features:

• Dual Primary 115/230VAC
• Operates on 50/60 Hz.
• Combination solder or quick connect terminals.
• Split bobbin construction eliminates the need for an electrostatic shield.
• Hi-pot tested to 2 KV RMS.
• Economical open style, channel frame - chassis mount design
• UL recognized & CSA certified.

Open style, chassis mount transformers with a 117V 50/60Hz primary and a 25V secondary.

• Primary 115 VAC, 60 Hz.
• Secondary 60 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

35VA chassis mount Power Transformer for isolating equipment from direct connection to the power line. It is constructed with non-concentrically wound coils. The primary and secondary are wound on separate arbors, then assembled on a laminate core side-by-side separated by insulation. This prevents electrical connection under normal or overload conditions between the primary and secondary windings. These units are designed with 1500V isolation between winding to winding and between winding and core. Materials and construction are rated for Class B insulation system.

Open style, chassis mount transformers with a 115V 60Hz primary and a 35V center tapped secondary.

Fender Original Hot Rod Deluxe Power Transformer. Equivalent to #036958.



Specifications



Primary
120 VAC @ 60 Hz (Black - White)


Secondary 1 (Red - Red)
495 VDC unloaded, 440 VDC @ 65.7 mA DC, 388 VDC @ 200 mA DC


Secondary 2 (Brown - Brown)
53.6 VAC @ 1.58 A AC


Secondary 3 (Green - Green)
6.6 VAC @ 3.75 A AC


Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.

Dual 117/234 VAC primary, 50/60 Hz. operation. 48 V series, 24 V parallel secondary.

• Universal primary with taps for 100, 120, 220 or 240 VAC, 50 / 60 Hz. (Except the 260A6 which is 117V, 50/60 Hz only)
• Designed for preamps, low power amps, general replacement, test equipment, etc.
• Economical, open frame, chassis mount - two hole (.187 dia. = G) channel bracket (figure #1) or four hole mounting (figure #2).
• Units include a Faraday shield between the primary and secondary windings. Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries.
• Minimum 5" long leads.
• For more selection check out our P-T300-X series of universal plate & filament transformers.

• Primary 115 VAC, 60 Hz.
• Designed for small power or bias supplies, test equipment, preamps etc.
• Economical , two hole, channel bracket, chassis mount.
• Minimum 5" long leads.
• Convenient 12.6 filament/auxiliary winding.

• Open style, chassis mount transformers with a 115V 60Hz primary and a 50V center tapped secondary.

Open style, chassis mount transformers with a 115V 60Hz primary and a 28V center tapped secondary.