1. Home
  2. Products
  3. Transformers & Chokes

Transformers & Chokes

products per page
P-T1750X-FENDER Transformer - Hammond, Output, replacement for Fender
  • Replacements for Fender Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $18.44
P-T167S10 Transformer - Hammond, Low Voltage / Filament, Enclosed, 10 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 10 C.T.
  • All secondaries center tapped, VAC (RMS)
  • Enclosed, 4 hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • UL listed (# E50394) & CSA certified (209651).
$55.43
P-T1182-6 Transformer - Hammond, Toroidal Power, 6V / 12V secondary
Dual 117/234 VAC primary, 50/60 Hz. operation. 12 V series, 6 V parallel secondary.mary, 50/60 Hz. operation.
Starting at $45.24
P-T300-X Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount
  • Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
    • NOTE: units are designed to operate with BOTH primary windings engaged.
    • See primary wiring information under resources.
  • Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
  • Highpot tested: 2,000 VAC
  • Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
  • Windings: Concentric wound for low stray field and low noise.
  • Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
  • Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
  • Conservative designs - CSA certified (209651).
Starting at $73.89
P-T266J14 Transformer - Hammond, Power, Low voltage, 14V/1A
Specifications:
  • Size: 14 VA
  • Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
  • Secondary VAC RMS Series: 14V @ 1 A
  • Secondary VAC RMS Parallel: 7V @ 2 A

Features:
  • Primary 117/234 VAC, 50/60 Hz.
  • Dual secondaries
  • Secondaries can be used as; a center tapped secondary, parallel connected or used individually
  • Units are designed for use with all windings engaged.
  • Open style.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C) for extra pr
$32.56
P-T166-8 Transformer - Hammond, Low Voltage / Filament, Open, 8.5 VCT
Open style, chassis mount transformers with a 115V 60Hz primary and an 8V or 8.5V secondary.
Starting at $20.67
Note:
P-T166G8:4
P-T166J8:8.5
P-T166L8:17
are special order items.
Note: some of these items are special order items.
P-TM9100O Transformer - Marshall, Output, 100 W, for JCM900
Genuine Marshall™ 100 watt output transformer for JCM900 and JCM2000.
$139.95
P-TF413160 Transformer - Fender, Power, for Deluxe Reverb 120V
Genuine Fender power transformer designed for use in the ‘65 Deluxe Reverb as well as the ‘68 Deluxe. Made to original fender specifications. 120V Primary
$74.95
On Backorder
P-T166-6 Transformer - Hammond, Low Voltage / Filament, Open, 6.3 VCT
  • Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 6.3V center tapped secondary.
Starting at $10.02
Note: P-T166K6: 7.56 is a special order item.
P-T166-18 Transformer - Hammond, Low Voltage / Filament, Open, 18 VCT
  • Open style, chassis mount transformers with a 115V 60Hz or 50/60Hz primary and an 18V center tapped secondary.
Starting at $8.75
Note:
P-T166B18:0.54
P-T166E18:5.4
P-T166J18:18
P-T166K18:27
are special order items.
Note: some of these items are special order items.
P-T166-80 Transformer - Hammond, Low Voltage / Filament, Open, 80 VCT
Open style, chassis mount transformers with a 115V 60Hz primary and an 80V center tapped secondary.
$31.00
P-T166-12-NOTAP Transformer - Hammond, Low Voltage / Filament, Open, 12 V no tap
Special Order Item
Open style, chassis mount transformers with a 117V 50/60Hz primary and a 12V secondary.
Starting at $12.41
Note: special order items require additional lead time. See our page on special order items.
P-C194A Choke - Hammond, for Fender Deluxe, Deluxe Reverb, etc.
Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications: Inductance ± 15% 4 H D.C. Current 50 mA Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$16.42
P-T169XS Transformer - Hammond, Isolation, 115V
  • Primary 115VAC, 60 Hz.
  • Secondary 115VAC
  • Electrostatic shield between primary & secondary
  • Connection by flexible leads, 8" minimum length
  • Perfect for circuit isolation or "Classic" bias power supply
  • CSA certified (209651)
  • Remember - These units do NOT convert line frequency
Starting at $60.19
P-T1182-12 Transformer - Hammond, Toroidal Power, 12V / 24V secondary
Dual 117/234 VAC primary, 50/60 Hz. operation. 24 V series, 12 V parallel secondary.
Starting at $45.85
P-TBFT-1B Transformer - One Electron, BFT-1B, Power
The BFT-1B from One Electron was designed to power a stereo amplifier using UBT-1's in each channel but will also power an 80 watt push-pull tube amplifier. The BFT-1B is slightly larger than earlier versions of the BFT-1, allowing lower flux density and cooler operation. The tapped high-voltage windings and three filament windings provide flexibility in design. An electrostatic shield between the primaries and secondaries reduces power-line noise coupling. The primary arrangements allows use on virtually any power grid in the world.
$225.00
P-T266M16 Transformer - Hammond, Power, Low voltage, 16V/3A
Specifications:
  • Size: 48 VA
  • Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
  • Secondary VAC RMS Series: 16V @ 3 A
  • Secondary VAC RMS Parallel: 8V @ 6 A

Features:
  • Primary 117/234 VAC, 50/60 Hz.
  • Dual secondaries
  • Secondaries can be used as; a center tapped secondary, parallel connected or used individually
  • Units are designed for use with all windings engaged.
  • Open style.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C) for extra pr
$34.73
P-TM950P Transformer - Marshall, Power, 50 W, for JCM 900
Genuine Marshall™ 50 watt power transformer for JCM900.
$115.00
P-T290-MARSHALL Transformer - Hammond, Guitar Amplifier, replacement for Marshall
  • Replacements for Marshall amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $96.50
P-T167G120 Transformer - Hammond, Low Voltage / Filament, Enclosed, 120 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 120 C.T.
  • All secondaries center tapped, VAC (RMS)
  • Enclosed, 4 hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • UL listed (# E50394) & CSA certified (209651).
$47.95
P-T167X-25 Transformer - Hammond, Low Voltage / Filament, Enclosed, 25 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 25 C.T.
  • All secondaries center tapped, VAC (RMS)
  • Enclosed, 4 hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • UL listed (# E50394) & CSA certified (209651).
Starting at $33.78
P-T166-120 Transformer - Hammond, Low Voltage / Filament, Open, 120 VCT
Open style, chassis mount transformers with a 115V 60Hz primary and a 120V center tapped secondary.
$26.87
P-T166-25-NOTAP Transformer - Hammond, Low Voltage / Filament, Open, 25 V no tap
Special Order Item
Open style, chassis mount transformers with a 117V 50/60Hz primary and a 25V secondary.
$18.40
Note: special order items require additional lead time. See our page on special order items.
P-C194D Choke - Hammond, Replacement for Vox AC30 reissue
Replacement for Vox AC30 reissue


Inductance ± 15%
5 H


D.C. Current
150 mA


Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$37.63
Don't see what you're looking for? Send us your product suggestions!