Transformers & Chokes

P-T298DT Transformer - Hammond, Line Step Up Isolation, Toroidal, 500 VA
Special Order Item
Capacity: 500 VA
Dimensions: 9" long by 6" wide by 4" height
Features:
  • Primary 120VAC, 50/60 Hz., Secondary 240VAC.
  • Provides circuit isolation.
  • Toroidal transformer for high isolation, low noise, light weight cool operation and low profile.
  • 50 or 60 Hz.
$291.53
Save 11%
Originally: $327.56
Note: special order items require additional lead time. See our page on special order items.
P-T850HA Audio Transformer - Hammond, 150/600Ω, Line Isolation
Special Order Item
  • 150/600 Ohm Primary Impedance
  • 300/1200 Ohm Secondary Impedance
  • Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware.
  • Sealed case and wax potted core internally for stable characteristics and long life.
  • Wide frequency response ± 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, may be down 1 db @ 20 Khz.)
  • Insertion loss of apx. 1 db.
  • Maximum power level +15 dbm. with specified characteristics, or higher levels with reduced low frequency performance.
  • Distortion is apx. 1.5% @ 20 Hz. under full power.
  • Electrostatic shield between pri. & sec. connected to the green lead.
  • Humbucking construction
  • Balanced split windings on pri. & sec. for circuit versatility. Primary may be used as a secondary and vice versa for impedance matching.
  • Lead length: Min. 4"
$130.14
Save 11%
Originally: $146.22
Note: special order items require additional lead time. See our page on special order items.
P-RC-1 Choke - One Electron, Audio, PRC-1, for Shunt Feed SE Output
The PRC-1 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.
$75.65
Save 11%
Originally: $85.00
P-T171X Transformer - Hammond, line isolation / plug & receptacle
Special Order Item
  • Primary 115VAC, 50 / 60 Hz., Secondary 115VAC
  • Provides complete circuit isolation.
  • Electrostatic shield between primary & secondary to greatly attenuate surges and noise.
  • Hi-pot tested to 2 KV RMS.
  • Circuit breaker in primary.
  • Standard 3-wire, grounded plug & receptacle.
  • Input (primary) connected to 5 foot long cord & standard North American plug (NEMA 5-15P).
  • Output (secondary) connected to 1 foot long "pig tail" cord, 3-wire, standard North American grounded receptacle (NEMA 5-15R).
  • North American Mark of Safety - C UL & UL listed (File #E211544)
  • Indoor use only
  • Remember - These units do NOT convert line frequency
Starting at $74.10
Save 11%
Originally: $83.26
Note: special order items require additional lead time. See our page on special order items.
P-T169C Transformer - Hammond, Isolation, 100VA
Special Order Item
Capacity: 100 VA
Features:
  • Primary 115VAC, 60 Hz.
  • Secondary taps @ 90, 100, 110, 115, 120 & 130VAC
  • Electrostatic shield between primary & secondary
  • Connection by flexible leads, 8" minimum length
  • Perfect for critical line voltage needs (examples: older "classic" tube equipment or Japanese 100V equipment).
  • CSA certified (# LR3902)
  • Remember - These units do NOT convert line frequency
$65.21
Save 11%
Originally: $73.27
Note: special order items require additional lead time. See our page on special order items.
P-RC-2 Choke - One Electron, Audio, PRC-2, for Shunt Feed SE Output
The PRC-2 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.
$62.26
Save 11%
Originally: $69.95
P-RC-3 Choke - One Electron, Audio, PRC-3, 225H for Preamp Output
The PRC-3 audio choke from One Electron was designed as a plate load for the output of either a high quality line amplifier or a phono preamp.
$62.26
Save 11%
Originally: $69.95
P-T169XS Transformer - Hammond, Line Isolation
Special Order Item
  • Primary 115VAC, 60 Hz.
  • Secondary 115VAC
  • Electrostatic shield between primary & secondary
  • Connection by flexible leads, 8" minimum length
  • Perfect for circuit isolation or "Classic" bias power supply
  • CSA certified (209651)
  • Remember - These units do NOT convert line frequency
Starting at $51.50
Save 11%
Originally: $57.87
Partially Out of Stock
Note: special order items require additional lead time. See our page on special order items.
P-T266PA6 Transformer - Hammond, Power, Low voltage, 6.3V/6A
Special Order Item
Specifications:
  • Size: 37.8 VA
  • Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
  • Secondary VAC RMS Series: 6.3V @ 6 A
  • Secondary VAC RMS Parallel: 3.15V @ 12 A

Features:
  • Primary 117/234 VAC, 50/60 Hz.
  • Dual secondaries
  • Secondaries can be used as; a center tapped secondary, parallel connected or used individually
  • Units are designed for use with all windings engaged.
  • Open style.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C) for e
$42.48
Save 11%
Originally: $47.73
Note: special order items require additional lead time. See our page on special order items.
P-T266N12 Transformer - Hammond, Power, Low voltage, 12.6V/4A
Special Order Item
Specifications:
  • Size: 50.4 VA
  • Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
  • Secondary VAC RMS Series: 12.6V @ 4 A
  • Secondary VAC RMS Parallel: 6.3V @ 8 A

Features:
  • Primary 117/234 VAC, 50/60 Hz.
  • Dual secondaries
  • Secondaries can be used as; a center tapped secondary, parallel connected or used individually
  • Units are designed for use with all windings engaged.
  • Open style.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C) for ex
$36.11
Save 11%
Originally: $40.57
Note: special order items require additional lead time. See our page on special order items.
P-T193X Filter Choke - Hammond, D.C. choke, Enclosed
  • Enclosed, 4-hole mount chokes
  • Tolerance of 15% on both inductance & resistance.
  • Inductances measured at rated D.C. current.
  • Minimum 8" long leads.
  • Units will exhibit less inductance at slightly higher currents or more at lower currents.
  • Perfect for high voltage power supply filtering, case matches power transformers & tube audio output transformers.
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
  • For more sizes and voltages (open - bracket mount type) - see P-T154-P-T156-X
  • Operating temperature range is -40C to 85C
Starting at $34.40
Save 11%
Originally: $38.65
Partially Out of Stock
Note:
P-T193T: 0.05 H / 2 A
P-T193N: 3 H / 500 mA
P-T193P: 5 H / 500 mA
P-T193G: 10 H / 150 mA
P-T193M: 10 H / 300 mA
P-T193Q: 10 H / 500 mA
P-T193B: 12 H / 100 mA
P-T193C: 20 H / 100 mA
are special order items.
Note: some of these items are special order items.
P-T266G36 Transformer - Hammond, Power, Low voltage, 36V/0.5A
Special Order Item
Specifications:
  • Size: 18 VA
  • Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
  • Secondary VAC RMS Series: 36V @ 0.5 A
  • Secondary VAC RMS Parallel: 18V @ 1 A

Features:
  • Primary 117/234 VAC, 50/60 Hz.
  • Dual secondaries
  • Secondaries can be used as; a center tapped secondary, parallel connected or used individually
  • Units are designed for use with all windings engaged.
  • Open style.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C) for extra
$33.99
Save 11%
Originally: $38.19
Note: special order items require additional lead time. See our page on special order items.
P-T266M16 Transformer - Hammond, Power, Low voltage, 16V/3A
Special Order Item
Specifications:
  • Size: 48 VA
  • Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
  • Secondary VAC RMS Series: 16V @ 3 A
  • Secondary VAC RMS Parallel: 8V @ 6 A

Features:
  • Primary 117/234 VAC, 50/60 Hz.
  • Dual secondaries
  • Secondaries can be used as; a center tapped secondary, parallel connected or used individually
  • Units are designed for use with all windings engaged.
  • Open style.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C) for extra pr
$33.99
Save 11%
Originally: $38.19
Note: special order items require additional lead time. See our page on special order items.
P-C194D Choke - Hammond, Replacement for Vox AC30 reissue
Replacement for Vox AC30 reissue


Inductance ± 15%
5 H


D.C. Current
150 mA


Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$33.49
Save 11%
Originally: $37.63
P-T266J14 Transformer - Hammond, Power, Low voltage, 14V/1A
Special Order Item
Specifications:
  • Size: 14 VA
  • Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
  • Secondary VAC RMS Series: 14V @ 1 A
  • Secondary VAC RMS Parallel: 7V @ 2 A

Features:
  • Primary 117/234 VAC, 50/60 Hz.
  • Dual secondaries
  • Secondaries can be used as; a center tapped secondary, parallel connected or used individually
  • Units are designed for use with all windings engaged.
  • Open style.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C) for extra pr
$31.86
Save 11%
Originally: $35.80
Note: special order items require additional lead time. See our page on special order items.
P-T266J48 Transformer - Hammond, Power, Low voltage, 48V/1A
Special Order Item
Specifications:
  • Size: 48 VA
  • Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
  • Secondary VAC RMS Series: 48V @ 1 A
  • Secondary VAC RMS Parallel: 24V @ 2 A

Features:
  • Primary 117/234 VAC, 50/60 Hz.
  • Dual secondaries
  • Secondaries can be used as; a center tapped secondary, parallel connected or used individually
  • Units are designed for use with all windings engaged.
  • Open style.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C) for extra p
$31.86
Save 11%
Originally: $35.80
Note: special order items require additional lead time. See our page on special order items.
P-C194C Choke - Hammond, replacement for Marshall Plexi JCM800
Replacement for Marshall Plexi JCM 800.


Inductance ± 15%
40 H


D.C. Current
50 mA


Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$31.26
Save 11%
Originally: $35.12
P-C194E Choke - Hammond, Replacement for Vox AC30 vintage
Replacement for Vox AC30 vintage


Inductance ± 15%
30 H


D.C. Current
100 mA


Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$30.58
Save 11%
Originally: $34.36
P-T109L Transformer - Hammond, 2W Audio Miniature Epoxy Potted
Special Order Item
Features:
  • Perfect for audio input, line matching, isolation or output transformer applications.
  • 2 watt (± 1.5 dB, 300 Hz. - 50 kHz.).
  • Epoxy potted in an attractive black molded case, Pin type P.C. board mount (min. 0.187" length).
  • Power level ratings are maximum at lowest frequency rating
  • Power can be increased slightly at higher frequencies.
  • Will withstand soldering for 10 sec. @ 260 degrees C, ambient temp. 85 degrees C max.
$29.49
Save 11%
Originally: $33.14
Note: special order items require additional lead time. See our page on special order items.
P-T229D40 Transformer - Hammond, Power, Low Voltage PC Mount
Special Order Item
Size: 48 VA
Secondary Series: 40V C.T. @ 1.2A
Secondary Parallel: 20V @ 2.4 A
Features:
  • Low profile mounting, dual - split bobbin design.
  • Low primary to secondary coupling, balanced windings, no electrostatic shield required and low EMF radiation due to semi-toroidal design.
  • Universal dual primary 115/230V - 50/60 Hz.
  • High insulation - Hipot of 1,750V RMS.
  • Class B insulation - 130 degrees C.
  • C UL US recognized.
$27.01
Save 11%
Originally: $30.35
Note: special order items require additional lead time. See our page on special order items.
P-T266G14 Transformer - Hammond, Power, Low voltage, 14V/0.5A
Special Order Item
Specifications:
  • Size: 7 VA
  • Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
  • Secondary VAC RMS Series: 14V @ 0.5 A
  • Secondary VAC RMS Parallel: 7V @ 1 A

Features:
  • Primary 117/234 VAC, 50/60 Hz.
  • Dual secondaries
  • Secondaries can be used as; a center tapped secondary, parallel connected or used individually
  • Units are designed for use with all windings engaged.
  • Open style.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C) for extra p
$25.49
Save 11%
Originally: $28.64
Note: special order items require additional lead time. See our page on special order items.
P-TM800-C-CE Filter Choke - Marshall Replacement, for JCM800
Replacement filter choke for Marshall JCM800s.
$22.21
Save 11%
Originally: $24.95
P-C194G Choke - Hammond, Replacement for Marshall Plexi
Replacement for Marshall Plexi Specifications:
  • Inductance ± 15%: 3 H
  • D.C. Current: 250 mA

Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$19.70
Save 11%
Originally: $22.14
P-TN-51X Transformer - Line Isolation, 35 VA, 115V, 300 mA, 1 x 115V
35VA chassis mount Power Transformer for isolating equipment from direct connection to the power line. It is constructed with non-concentrically wound coils. The primary and secondary are wound on separate arbors, then assembled on a laminate core side-by-side separated by insulation. This prevents electrical connection under normal or overload conditions between the primary and secondary windings. These units are designed with 1500V isolation between winding to winding and between winding and core. Materials and construction are rated for Class B insulation system.
$19.54
Save 11%
Originally: $21.95
Don't see what you're looking for? Send us your product suggestions!