1. Home
  2. Products
  3. Transformers & Chokes

Transformers & Chokes

products per page
P-TF26477 Transformer - Fender®, Power, for Tone Master
Fender® Original Tone Master Power Transformer. Equivalent to #026477.
$179.95
On Backorder
P-T162XSEA Transformer - Hammond, Output, Single-Ended, 30 W
  • Over designed for single ended tube output circuits (triode, tetrode or pentode tubes).
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response at least 20 Hz. to 20 Khz. at full rated power (± 1 db max. ref.
Starting at $151.64
P-TM9100O Transformer - Marshall, Output, 100 W, for JCM900
Genuine Marshall™ 100 watt output transformer for JCM900 and JCM2000.
$139.95
P-TM45O Transformer - Marshall, Output, for JTM45
Genuine Marshall™ output transformer for JTM45.
$135.00
P-TUBT-2 Transformer - One Electron, Output, 4800 Ω to 16/8/4 Ω
The UBT-2 from One Electron is the same size and power (15 watts) as the UBT-1, but has a higher primary impedance suitable for single tubes running at B+ voltages of 400 to 500 volts, such as: 50, WE 300B,etc.
$129.95
P-TUBT-1 Transformer - One Electron, Output, 1600 Ω to 16/8/4 Ω
The UBT-1 from One Electron is a low-impedance single-ended output transformer intended for parallel combinations of tubes running a B+ voltages of 250 to 325 volts, such as: two or three EL34s (triode connected), three 2A3s, two 300Bs, two 6AS7s, etc., as well as single sweep tubes run in 'enhanced-triode' mode, resulting in 10 to 15 watts of output power.
$125.00
P-TM950O Transformer - Marshall, Output, 50 W, for JCM 900
Genuine Marshall™ output transformer for JCM900 and JCM2000.
$117.80
P-T1650XA Transformer - Hammond, Tube Output, Easy Wire Secondary
  • Designed for push-pull tube output circuits.
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Starting at $112.58
P-TUBT-3 Transformer - One Electron, Output, 3000 Ω to 16/8/4 Ω
The UBT-3 from One Electron is the same size and power (15 watts) as the UBT-1, but has a primary impedance suitable for single or paralleled tubes running at B+ voltages of 300 to 400 volts, such as: 2A3, WE 300B, 50, etc.
$109.95
P-T1750X-VOX Transformer - Hammond, Output, replacement for Vox
  • Replacements for Vox Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $95.44
P-TF36483 Transformer - Fender®, Power, for '59 Bassman Reissue
Fender® Original '59 Bassman Reissue Power Transformer. Equivalent to #036483.
$89.95
P-T1650X Transformer - Hammond, Tube Output, Push-Pull
  • Designed for push-pull tube output circuits.
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Starting at $85.25
P-RC-1 Choke - One Electron, Audio, PRC-1, for Shunt Feed SE Output
The PRC-1 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.
$85.00
P-TM0100 Transformer - Marshall Replacement, Output, 100 W
Great for upgrading later issue Marshall™ amps. Gives great classic sound.
Good replacement for JMP and JCM 800s. for EL34!
$81.95
On Backorder
P-TF37610 Transformer - Fender®, Power, for '65 Twin Reverb Reissue
Made precisely to the original Fender® specifications. Drop-in replacement for '65 Twin Reverb Reissue. Made in the USA. 120V Primary.
$79.95
On Backorder
P-TM050 Transformer - Marshall Replacement, Output, 50 W
Great for upgrading later issue Marshall™ amps. Good replacement for JMP and JCM 800s.
$76.95
P-TF413160 Transformer - Fender, Power, for Deluxe Reverb 120V
Genuine Fender power transformer designed for use in the ‘65 Deluxe Reverb as well as the ‘68 Deluxe. Made to original fender specifications. 120V Primary
$74.95
P-T290-VOX Transformer - Hammond, Guitar Amplifier, replacement for Vox
  • Replacement for Vox amplifiers
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $72.94
P-RC-2 Choke - One Electron, Audio, PRC-2, for Shunt Feed SE Output
The PRC-2 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.
$69.95
P-TF22871 Transformer - Fender® Replacement, Output, 50 W, 4 Ohm
Replacement for Bassman heads. Equivalent to #125A13A & #022871.
$69.95
P-RC-3 Choke - One Electron, Audio, PRC-3, 225H for Preamp Output
The PRC-3 audio choke from One Electron was designed as a plate load for the output of either a high quality line amplifier or a phono preamp.
$69.95
P-T1750ORF Transformer - Hammond, Output, replacement for Orange Rocker 30
Hammond output transformer - replacement for Orange Rocker 30 Specifications: Part No. Pri Ohms Sec Ohms Amplifier Type Watts Bobbin/Paper Winding Equivalent To P-T1750ORF 6,000 C.T. 8, 16 Push-Pull 35 W Bobbin OT199SL
$58.50
P-TF36485 Transformer - Fender®, Output, 50 W, 2 Ω
Fender® Original '59 Bassman Reissue output transformer. Equivalent to #036485.
$51.95
P-T118944 Transformer - Hammond, Radiola III-A Replacement Audio
Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features
  • Primary: 4000 turns, #41 wire (lugs 4 & 2)
  • Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
  • Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
  • Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
  • Lamination Core Size: 5/8" x 1/2"
  • Weight: 7 oz.
$48.25
Don't see what you're looking for? Send us your product suggestions!