Transformers & Chokes

Capacity: 500 VA
Dimensions: 9" long by 6" wide by 4" height
Features:

• Primary 120VAC, 50/60 Hz., Secondary 240VAC.
• Provides circuit isolation.
• Toroidal transformer for high isolation, low noise, light weight cool operation and low profile.
• 50 or 60 Hz.

Dual 117/234 VAC primary, 50/60 Hz. operation. 80 V series, 40 V parallel secondary.

Capacity: 500VA Features:

• Single winding does not provide isolation, for use where equipment is already isolated and only voltage change is required.
• World wide applications, 50 or 60 Hz.

Dual 117/234 VAC primary, 50/60 Hz. operation. 48 V series, 24 V parallel secondary.

• Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
  
  • NOTE: units are designed to operate with BOTH primary windings engaged.
  • See primary wiring information under resources.
• Bias Tap: 50 VAC tap from high voltage secondary C.T.

• Replacements for Marshall amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

• Primary 115VAC, 50 / 60 Hz., Secondary 115VAC
• Provides complete circuit isolation.
• Electrostatic shield between primary & secondary to greatly attenuate surges and noise.
• Hi-pot tested to 2 KV RMS.
• Circuit breaker in primary.
• Standard 3-wire, grounded plug & receptacle.
• Input (primary) connected to 5 foot long cord & standard North American plug (NEMA 5-15P).
• Output (secondary) connected to 1 foot long "pig tail" cord, 3-wire, standard North American grounded receptacle (NEMA 5-15R).
• North American Mark of Safety - C UL & UL listed (File #E211544)
• Indoor use only
• Remember - These units do NOT convert line frequency

• Designed for drop in replacement of original units. Upgraded units with variable voltage.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120 for 120 V basic transformers, P-T290-FENDER-240 for 240 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.

• Primary 115 VAC, 50 / 60 Hz.
• At 2,000 VAC and above, secondary leads are through rubber bushings
• Units can be run full wave bridge or full wave C.T.
• V.A. is a C.C.S. rating
• Current ratings are CCS (Continuous Commercial Service) & ICAS ratings (Intermittent Commercial or Amateur Service).
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Class A insulation (105 degrees C).
• Hi-Pot test at a minimum of twice secondary voltage
• Conservative designs - CSA certified (209651).

• Replacement for Vox amplifiers
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Dual 117/234 VAC primary, 50/60 Hz. operation. 120 V series, 60 V parallel secondary.

• Replacement for Yorkville/Traynor amplifiers
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Part No. Primary Secondary 1 Secondary 2 Secondary 3 Yorkville / Traynor Amp Yorkville / Traynor Part No VAC Hz. P-T290TRA 120 V 60 Hz. 320 V @ 600 mA 60 V @ 50 mA 6.3 V.C.T. @ 9 A 100 Watt Bass A-1380 P-T290TRB 120 V 60 Hz. 620 V @ 115 mA 6.3 V.C.T. @ 115 mA YBA2-B A-1314 P-T291JX 120 V 60 Hz. 320 V @ 500 mA 60 V @ 20 mA 6.65 V.C.T.

Low Voltage, Filament High Current, Chassis Mount. 115 V primary.

• Replacement for Ampeg amplifiers
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Part No.
Primary
Ampeg Model Names
Ampeg Part No
Bobbin/Paper Wound


VAC
Hz.




P-T291GX
120 V
60 Hz.
B25
12XA
Bobbin


P-T290CAZ
117 V
60 Hz.
Gemini VI 25W
PT 113
Bobbin


P-T290ETX
120 V
60 Hz.
Super Echo Twin
PT 109
Bobbin


P-T291HX
110 / 115 / 230 V
50 / 60 Hz.
V50H
94-270-030
Bobbin

Dual 117/234 VAC primary, 50/60 Hz. operation. 180 V series, 90 V parallel secondary.dary.

Primary 115 VAC 60 Hz.
Secondary DC current measured with cap. input filter, full wave (two diode) C.T., rectifier circuit.
Enclosed, 4 hole chassis mount.
Minimum 6 long leads.
2" X 2" vertical mounting centers.
Class A insulation (105 degrees C).
Hi-Pot test of 2000 V RMS.
Conservative designs - CSA certified (# LR3902).
3.2lbs
Secondary: 250-0-250 V100 mA
Filament winding 1: 5 V2 A
Filament winding 2: 6.3 V3 A

• Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
  
  • NOTE: units are designed to operate with BOTH primary windings engaged.
  • See primary wiring information under resources.
• Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
• Highpot tested: 2,000 VAC
• Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
• Windings: Concentric wound for low stray field and low noise.
• Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
• Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
• Conservative designs - CSA certified (209651).

• Horizontal mount. For Vertical Mount, see P-T263-X
• Primary 117 VAC, 50/60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).
• For Vertical Mount, see P-T263-X

Capacity: 100 VA
Features:

• Primary 115VAC, 60 Hz.
• Secondary taps @ 90, 100, 110, 115, 120 & 130VAC
• Electrostatic shield between primary & secondary
• Connection by flexible leads, 8" minimum length
• Perfect for critical line voltage needs (examples: older "classic" tube equipment or Japanese 100V equipment).
• CSA certified (# LR3902)
• Remember - These units do NOT convert line frequency

• Universal primary with taps for 100, 120, 220 or 240 VAC, 50 / 60 Hz. (Except the 260A6 which is 117V, 50/60 Hz only)
• Designed for preamps, low power amps, general replacement, test equipment, etc.
• Economical, open frame, chassis mount - two hole (.187 dia. = G) channel bracket (figure #1) or four hole mounting (figure #2).
• Units include a Faraday shield between the primary and secondary windings. Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries.
• Minimum 5" long leads.
• For more selection check out our P-T300-X series of universal plate & filament transformers.

Open style, chassis mount transformers with a 117V 50/60Hz primary and a 72V center tapped secondary.

• Primary 115VAC, 60 Hz.
• Secondary 115VAC
• Electrostatic shield between primary & secondary
• Connection by flexible leads, 8" minimum length
• Perfect for circuit isolation or "Classic" bias power supply
• CSA certified (209651)
• Remember - These units do NOT convert line frequency

• Primary 115 VAC, 60 Hz.
• Secondary 60 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

Open style, chassis mount transformers with a 117V 50/60Hz primary and a 48V center tapped secondary.