Transformers & Chokes

- Replacements for Fender Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $18.44

- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers
Warning: Not all amplifier models of the same name use the same transformer model.
Starting at $36.25

Features
- Economical "open bracket" - channel mount.
- Tolerance of 15% on both inductance & resistance.
- Inductances measured at rated D.C.
Starting at $13.02

- Vertical Mount. For Horizontal Mount, see P-T263-Z
- Primary 115 VAC, 60 Hz. - except as noted
- Enclosed, 4 hole, chassis mount.
- Minimum 6" long leads.
- Units can be run full wave bridge or full wave C.T.
- Class A insulation (105 degrees C).
- Hi-Pot test of 2,000V RMS.
- Conservative designs - CSA certified (209651).
Starting at $50.06

Equivalent to Stancor A53-C. 1:3 ratio overall. Center tapped secondary may be used for push-pull grids.Specifications Max. Primary Current: 10 mA Impedance Primary to Secondary (Ohms): 10,000 to 90,000
$16.95

Replacement for Fender Bandmaster, Dual Showman, Pro Reverb, Twin Super Equivalent to Manufacturer part number 125C1A & 022699 Specifications:
Features:
- Inductance ± 15%: 4 H
- D.C. Current: 90 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs.
$17.86

- Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 6.3V center tapped secondary.
Starting at $10.02

- Replacements for Marshall Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $37.50

Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications: Inductance ± 15% 4 H D.C. Current 50 mA Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$16.42

Replacement for Fender Super Reverb, Pro Reverb, Bandmaster, and Tweed Bassman. Includes rectifier tap.
Equivalent to #125P5D & #022798.
Equivalent to #125P5D & #022798.
$79.95

Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
Starting at $22.14

- Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
- Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
- Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
- Tables provided with transformer listing 90 pre-calculated impedance ratios.
Starting at $36.82

- Primary 115 VAC, 60 Hz.
- Designed for small power or bias supplies, test equipment, preamps etc.
- Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
- Economical , two hole, channel bracket, chassis mount.
- Minimum 5" long leads.
- Convenient 6.3 filament/auxiliary winding.
Starting at $33.87

Fender Original Hot Rod Deluxe and Blues Deluxe output transformer. 40 watts. Equivalent to #050438.
$41.50

- Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits.
- Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE).
- For push-pull output use, see P-T125A - optimized for push-pull tube output circuits.
- Open style with minimum 12" long primary & secondary leads leads.
- All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C. core saturation.
- Primary impedance range from 2,500 to 10,000 Ohms.
- Secondary impedance range from 4 to 32 Ohms.
Part No.
Audio Power
Max D.C. Bias
Dimensions (Inches)
A
B
C
D
E
G Mtg.
Starting at $45.84

Specifications Output 8 W Primary Impedance 4,000 to 9,000 Ω Mounting Centers 2.375" Weight 0.7 lbs
$21.39

Replacement for Fender Deluxe, Deluxe Reverb. Equivalent to #125P23B. Note: Does not fit Reissue '65 Reverb.
$74.50

- Designed for push-pull tube output circuits.
- Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
- Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Starting at $85.25

- Replacements for Marshall amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $96.50

An Isolation Power Transformer for isolating equipment from direct connection to the power line. The transformer is constructed with non-concentrically wound coils. The primary and secondary are wound on separate arbors, then assembled on a laminate core side-by-side separated by insulation. This prevents electrical connection, under normal or overload conditions, between the primary and secondary windings.
$15.95

Fender Original Hot Rod Deluxe Power Transformer. Equivalent to #036958.
Specifications
Primary
120 VAC @ 60 Hz (Black - White)
Secondary 1 (Red - Red)
495 VDC unloaded, 440 VDC @ 65.7 mA DC, 388 VDC @ 200 mA DC
Secondary 2 (Brown - Brown)
53.6 VAC @ 1.58 A AC
Secondary 3 (Green - Green)
6.6 VAC @ 3.75 A AC
Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
Specifications
Primary
120 VAC @ 60 Hz (Black - White)
Secondary 1 (Red - Red)
495 VDC unloaded, 440 VDC @ 65.7 mA DC, 388 VDC @ 200 mA DC
Secondary 2 (Brown - Brown)
53.6 VAC @ 1.58 A AC
Secondary 3 (Green - Green)
6.6 VAC @ 3.75 A AC
Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
$58.95

Coil assembly for P-T156. Use your own iron to preserve mechanical fit. Coil window is 1/2 x ½".
$14.75

Replacement for Fender Vibrolux and Tremolux Blackface AA763 (1963-1966).
Equivalent to #125P26A & # 036483. 35 Watts.
Equivalent to #125P26A & # 036483. 35 Watts.
$69.95

A good upgrade for later issue Marshall amplifiers. Good replacement for JMP and JCM 800s for EL34!
$86.95