Transformers & Chokes

Molded powdered iron core.
1-1/4 long axial leads.
High inductance & high current.
L measured at 1 Khz. Inductance: 250 µH20% tolerance
DC resistance ohms: .17
Self Resonant Frequency (MHz): 1.5
Maximum DC current amps: 2.5
Coil diameter (in): .43
Core Length (in): 1.25
1-1/4 long axial leads.
High inductance & high current.
L measured at 1 Khz. Inductance: 250 µH20% tolerance
DC resistance ohms: .17
Self Resonant Frequency (MHz): 1.5
Maximum DC current amps: 2.5
Coil diameter (in): .43
Core Length (in): 1.25
$1.65

Replacement choke for the Fender® part numbers 125C3A and 022707 as used in the Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb, 1964 Blackface 6G15 Reverb, and others. This choke is rated 4H 50mA DC.
$11.95

Replacement choke for the Fender® part numbers 125C1A, 022699, and 036468 as used in the Bandmaster, Dual Showman, Pro Reverb, Twin Reverb, Super Reverb, and others. This choke is rated 4H 90mA DC.
$18.95

Replacement for Fender Bandmaster, Dual Showman, Pro Reverb, Twin Super Equivalent to Manufacturer part number 125C1A & 022699 Specifications:
Features:
- Inductance ± 15%: 4 H
- D.C. Current: 90 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs.
$25.98

Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications: Inductance ± 15% 4 H D.C. Current 50 mA Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$21.95

Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
Starting at $28.95

Replacement for Vox AC30 reissue
Inductance ± 15%
5 H
D.C. Current
150 mA
Features:
Inductance ± 15%
5 H
D.C. Current
150 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$52.00

Replacement for Vox AC30 vintage
Inductance ± 15%
30 H
D.C. Current
100 mA
Features:
Inductance ± 15%
30 H
D.C. Current
100 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$47.48
16H @ 40 mA guitar amplifier replacement for Vox TB35C2 Tony Bruno. Physically, parts were designed to look similar to original factory units (where possible). Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
$29.10

The PRC-3 audio choke from One Electron was designed as a plate load for the output of either a high quality line amplifier or a phono preamp.
$49.95

- Enclosed, 4-hole mount chokes
- Tolerance of 15% on both inductance & resistance.
- Inductances measured at rated D.C. current.
- Minimum 8" long leads.
- Units will exhibit less inductance at slightly higher currents or more at lower currents.
- Perfect for high voltage power supply filtering, case matches power transformers & tube audio output transformers.
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
- For more sizes and voltages (open - bracket mount type) - see P-T154-P-T156-X
- Operating temperature range is -40C to 85C
Starting at $47.57
Save 10%
Originally: $52.95

Features
- Economical "open bracket" - channel mount.
- Tolerance of 15% on both inductance & resistance.
- Inductances measured at rated D.C.
Starting at $16.75

Special Order Item
- Both series operate on 50/60 Hz current
- Low profile, split bobbin design.
- Dual winding secondaries, non-concentrically wound
- Units are designed so that all windings must be used
- Low primary to secondary coupling - no electrostatic shield required.
- High insulation - Hipot of 2,500V RMS.
- Class B insulation - 130 degrees C.
- c UL us recognized
Starting at $10.19

Includes: 3 pole, 3 position rotary switch (3P3T), 1/4" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with 1/4" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and 1/4" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
$11.95

Small 42TM018 audio transformers with a 10KΩ:600Ω impedance. This transformer is a popular choice for pickup simulators in various effects such as fuzz pedals. The leads are soft metal wire and can be adjusted to fit a variety of applications. RoHS compliant. Rated for 200mW.
$4.75

Small 42TM022 audio transformers with a 1.5KΩ:600Ω impedance. This transformer is a popular choice for octavia style builds as well as ring modulators. The leads are soft metal wire and can be adjusted to fit a variety of applications. RoHS compliant. Rated for 200mW.
$5.65

Equivalent to Stancor A53-C. 1:3 ratio overall. Center tapped secondary may be used for push-pull grids.Specifications Max. Primary Current: 10 mA Impedance Primary to Secondary (Ohms): 10,000 to 90,000
$16.95

Coil assembly for P-T156. Use your own iron to preserve mechanical fit. Coil window is 1/2 x ½".
$15.65

Genuine Fender power transformer designed for use in the ‘65 Deluxe Reverb as well as the ‘68 Deluxe. Made to original fender specifications. 120V Primary
$74.95

Replacement for Bassman heads. Equivalent to #125A13A & #022871.
$53.58
Save 23%
Originally: $69.95

Fender® Original '59 Bassman Reissue output transformer. Equivalent to #036485.
$61.35

Fender Original Hot Rod Deluxe and Blues Deluxe output transformer. 40 watts. Equivalent to #050438.
$59.95

Fender Original Blues Junior Power Transformer. Equivalent to #049967.
$50.95

Fender® Original '59 Bassman Reissue Power Transformer. Equivalent to #036483.
$96.95