Transformers & Chokes

• Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
  
  • NOTE: units are designed to operate with BOTH primary windings engaged.
  • See primary wiring information under resources.
• Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
• Highpot tested: 2,000 VAC
• Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
• Windings: Concentric wound for low stray field and low noise.
• Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
• Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
• Conservative designs - CSA certified (209651).

• Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
  
  • NOTE: units are designed to operate with BOTH primary windings engaged.
  • See primary wiring information under resources.
• Bias Tap: 50 VAC tap from high voltage secondary C.T.

• Primary 115 VAC, 50 / 60 Hz.
• At 2,000 VAC and above, secondary leads are through rubber bushings
• Units can be run full wave bridge or full wave C.T.
• V.A. is a C.C.S. rating
• Current ratings are CCS (Continuous Commercial Service) & ICAS ratings (Intermittent Commercial or Amateur Service).
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Class A insulation (105 degrees C).
• Hi-Pot test at a minimum of twice secondary voltage
• Conservative designs - CSA certified (209651).

Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with hardware. Includes wire leads (minimum length of 4"). Frequency response +/- 0.5 db max. from 50 Hz. to 15 Khz. Insertion loss of apx. 1 db. Maximum power level +15 dbm. (except 841A, 842A & 844A which are +20 dbm) with specified characteristics, or higher levels with reduced low frequency performance.

Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware. Sealed case and wax potted core internally for stable characteristics and long life. Wide frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, may be down 1 db @ 20 Khz.) Insertion loss of apx. 1 db.

• Vertical mount, split bobbin design.
• Non-concentric wound.
• Low primary to secondary coupling - no electrostatic shield required.
• High insulation - Hipot of 2,000V RMS.
• Class B insulation - 130 degrees C.
• CSA certified (File # LR3902) and UL recognized (File #E207860).

• Operate on 50/60 Hz current
• Low profile, split bobbin design.
• Dual winding secondaries, non-concentrically wound
• Units are designed so that all windings must be used
• Low primary to secondary coupling - no electrostatic shield required.
• Universal dual primary 115/230V
• High insulation - Hipot of 2,500V RMS.
• Class B insulation - 130 degrees C.

Open style, chassis mount transformers with a 115V 60Hz primary and a 9V center tapped secondary.

Open style, chassis mount transformers with a 117V 50/60Hz primary and a 24V secondary.

Open style, chassis mount transformers with a 117V 50/60Hz primary and a 25V secondary.

Secondary VAC: 10V C.T.
Current: 5 A
VA Rating: 50
Features:

• Single Primary 115VAC
• Operates on 50/60 Hz.
• Combination solder or quick connect terminals.
• Split bobbin construction eliminates the need for an electrostatic shield.
• Hi-pot tested to 2 KV RMS.
• Economical open style, channel frame - chassis mount design
• UL recognized & CSA certified.

Secondary VAC: 12.6V C.T.
Current: 4 A
VA Rating: 50.4
Features:

• Dual Primary 115/230VAC
• Operates on 50/60 Hz.
• Combination solder or quick connect terminals.
• Split bobbin construction eliminates the need for an electrostatic shield.
• Hi-pot tested to 2 KV RMS.
• Economical open style, channel frame - chassis mount design
• UL recognized & CSA certified.

Low profile mounting, dual - split bobbin design. 12VA.

European plug type Used in: Austria; Belgium; Finland; France; Germany; Middle East; Netherlands; Norway; Parts of Africa, Asia ,South America, China, Tahiti and Caribbean; Sweden Features:

• For use with Hammond transformers
• Heavy duty design with plastic shell & double wipe contacts.
• Indoor use only.
• Allows for ground connection between equipment and international power sources.
• Adaptors do not affect voltages, they are a mechanical device only to match foreign "pin-outs" of receptacles and/or plugs.