Transformers & Chokes

Specifications

• Primary: 115 VAC, 60 Hz
• Secondary: 6.3 VCT, 16 A
• Mounting Centers: 2" x 2.19", vertical

Key Features

• Center tapped secondary
• Enclosed, 4 hole chassis mount
• Minimum 6" long leads
• Dual bobbin design - no electrostatic shield required
• Class B insulation (130 degrees, C)
• Hi-Pot test of 2,000 V RMS
• UL listed (# E50394) & CSA certified (# LR3902)

Replacement for Dual Showman, Twin Reverb Equivalent to manufacturer part number #125A29A and #022889 Warning: Not all amplifier models of the same name use the same transformer model.

Specifications Audio Watts: 8 watts Primary Impendance (Ohms): 10K center-tapped Secondary Impendance (Ohms): 2/4/8 Mounting centers: 2-3/8u-bracket Weight: 1.0 lbs. Cat. No. Dimensions (Inches) A B C D G Mtg. Hole 125H 2.81 1.4 1.7 2.36 0.187

• Designed for push-pull tube output circuits.
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.

• Designed for push-pull tube output circuits.
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.

Replacement for Bassman Equivalent to manufacturer part number #125A13A and #022871 Warning: Not all amplifier models of the same name use the same transformer model.

The BFT-1B from One Electron was designed to power a stereo amplifier using UBT-1's in each channel but will also power an 80 watt push-pull tube amplifier. The BFT-1B is slightly larger than earlier versions of the BFT-1, allowing lower flux density and cooler operation. The tapped high-voltage windings and three filament windings provide flexibility in design. An electrostatic shield between the primaries and secondaries reduces power-line noise coupling. The primary arrangements allows use on virtually any power grid in the world.

Fender® Original '59 Bassman Reissue output transformer. Equivalent to #036485.

• Inductance: 15 H
• D.C. Current: 30 mA
• Resistance: 1026 ohms
• Maximum Operating Voltage: 400 V
• Features
  
  • Economical "open bracket" - channel mount.
  • Tolerance of 15% on both inductance & resistance.
  • Inductances measured at rated D.C.

• Inductance: 1 H
• D.C. Current: 300 mA
• Resistance: 40 ohms
• Maximum Operating Voltage: 400 V
• Features
  
  • Economical "open bracket" - channel mount.
  • Tolerance of 15% on both inductance & resistance.
  • Inductances measured at rated D.C.

Specifications

• Primary: 115 VAC, 60 Hz
• Secondary: 6.3 VCT, 10 A
• Mounting Centers: 2" x 1.69", vertical

Key Features

• Center tapped secondary
• Enclosed, 4 hole chassis mount
• Minimum 6" long leads
• Dual bobbin design - no electrostatic shield required
• Class B insulation (130 degrees, C)
• Hi-Pot test of 2,000 V RMS
• UL listed (# E50394) & CSA certified (# LR3902)

Replacement for Vox AC30 vintage
Specifications:

• Inductance ± 15%: 30 H
• D.C. Current: 100 mA

Features:

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Inductances measured at rated D.C. current.
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Replacement for JMP, JCM800 Specifications

• Primary: 3,200 C.T.Ω
• Secondary: 4Ω, 8Ω, 16Ω
• Power: 50 W
• Amp Type: Push-Pull

Features:

• >Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Specifications:

• Size: 59 VA
• Dual Primary: 115 VAC, 125 VAC, 60 Hz.
• A.C. High Voltage Secondary RMS: 550V.C.T.

Specifications:

• Size: 198 VA
• Dual Primary: 115 VAC, 125 VAC, 60 Hz.
• A.C. High Voltage Secondary RMS: 750V.C.T. @ 201mA
• Filament Winding #1: 5 V C.T. @ 3 A
• Filament Winding #2: 6.3 V C.T.

• Universal Primary - 100, 110, 120, 200, 220, 240 VAC 50/60 Hz.
• High voltage secondary designed for full wave center tapped use.
• 50 VAC bias tap from high voltage secondary C.T.
• Black epoxy painted to match our P-T1650 series of output transformers.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000 V RMS.
• Windings are concentric wound for low stray field and low noise.

Secondary: 300-0-300 V, 201 mA Filament winding 1 : 5 VCT, 3 A Filament winding 2 : 6.3 VCT, 5 A Mounting centers: 3" x 2.81" vertical mount Weight: 8

Replacement for Bassman heads. Equivalent to #125A13A & #022871.

Genuine Marshall™ output transformer for JTM45.

Genuine Marshall™ 100 watt output transformer for JCM900 and JCM2000.

• Inductance: 2 H
• D.C. Current: 100mA
• Resistance: 175 ohms
• Maximum Operating Voltage: 300 V

Features

• Economical "open bracket" - channel mount.
• Tolerance of 15% on both inductance & resistance.
• Inductances measured at rated D.C. current.
• Minimum 5" long leads.
• Units will exhibit less inductance at slightly higher currents or more inductance at lower currents.
• Perfect for high voltage power supply filtering.
• Every unit is Hipot tested (100%) at 1,500 VAC
• Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Part No.: Inductance ± 15%: D.C.

Replacement for Marshall Plexi JCM 800.
Specifications:

• Inductance ± 15%: 40 H
• D.C. Current: 50 mA

Features:

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Inductances measured at rated D.C. current.
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

• Designed for push-pull tube output circuits.
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.

• Designed for push-pull tube output circuits.
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.

Replacement for Tweed Bassman, Super Reverb Equivalent to manufacturer part number #125A9A and #022855 Warning: Not all amplifier models of the same name use the same transformer model.