Transformers & Chokes

Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features

• Primary: 4000 turns, #41 wire (lugs 4 & 2)
• Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
• Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
• Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
• Lamination Core Size: 5/8" x 1/2"
• Weight: 7 oz.

Specifications Audio Watts: 8 watts Primary Impendance (Ohms): 10K center-tapped Secondary Impendance (Ohms): 2/4/8 Mounting centers: 2-3/8u-bracket Weight: 1.0 lbs. Cat. No. Dimensions (Inches) A B C D G Mtg. Hole 125H 2.81 1.4 1.7 2.36 0.187

• Over designed for single ended tube output circuits (triode, tetrode or pentode tubes).
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response at least 20 Hz. to 20 Khz. at full rated power (± 1 db max. ref.

• Replacements for Vox Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Developed in response to requests from the Collins Collectors Association"this is a matching audio transformer for older equipment with 600 ohm audio outputdriving modern speakers. Or for "classic" high impedance speakers used with newer equipmentsimply swap primary for secondary (ie...4 or 8 ohm input and 600 ohms out). Key Features Isolation unit: (i.e.

• Open style, chassis mount transformers with a 115V 60Hz primary and a 10V center tapped secondary

• Horizontal mount. For Vertical Mount, see P-T263-X
• Primary 117 VAC, 50/60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).
• For Vertical Mount, see P-T263-X

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120 for 120 V transformers, P-T290-Fender-120-UP for upgraded 120 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.

Studio Grade Impedance Matching, 1140 Series. ​Designed with Nickel alloy cores for high performance and Wide Bandwidth. Frequency Response: 20 Hz – 20 kHz ±0.35 dB, (ref. @ 1 kHz). Low distortion at levels up to +27 dBu @ 20 Hz. Excellent Shielding – Mu Metal enclosures

Open style, chassis mount transformers with a 115V 60Hz or 50/60Hz primary and a 14V center tapped secondary.

• Primary 115 VAC, 60 Hz.
• Secondary 5 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

Replacement for Vox AC30 vintage


Inductance ± 15%
30 H


D.C. Current
100 mA


Features:

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Inductances measured at rated D.C. current.
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Studio Grade Impedance Matching, 1140 Series. ​Designed with Nickel alloy cores for high performance and Wide Bandwidth. Frequency Response: 20 Hz – 20 kHz ±0.35 dB, (ref. @ 1 kHz). Low distortion at levels up to +27 dBu @ 20 Hz. Open Style

• Designed for general purpose or replacement use in push-pull or phase inverter tube driver circuits.
• Should not be used for single ended applications. They have no gap for DC bias current present in SE mode.
• Open style with minimum 5" long primary leads.
• Minimum frequency response 150 Hz. - 15 Khz (+/- 1db max. ref. 1 Khz.) at full rated power.
• Core material is Grain Oriented Silicon Steel.

• Open style, chassis mount transformers with a 115V 60Hz primary and a 50V center tapped secondary.

• Replacements for Yorkville/Traynor Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Specifications:

• Size: 15 VA
• Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
• Secondary VAC RMS Series: 5V @ 3 A
• Secondary VAC RMS Parallel: 2.5V @ 6 A

Features:

• Primary 117/234 VAC, 50/60 Hz.
• Dual secondaries
• Secondaries can be used as; a center tapped secondary, parallel connected or used individually
• Units are designed for use with all windings engaged.
• Open style.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees, C) for extra p

Primary 115 VAC 60 Hz.
Secondary DC current measured with cap. input filter, full wave (two diode) C.T., rectifier circuit.
Enclosed, 4 hole chassis mount.
Minimum 6 long leads.
2" X 2" vertical mounting centers.
Class A insulation (105 degrees C).
Hi-Pot test of 2000 V RMS.
Conservative designs - CSA certified (# LR3902).
3.2lbs
Secondary: 250-0-250 V100 mA
Filament winding 1: 5 V2 A
Filament winding 2: 6.3 V3 A

Studio Grade Impedance Matching, 1140 Series. ​Designed with Nickel alloy cores for high performance and Wide Bandwidth. Frequency Response: 20 Hz – 20 kHz ±0.35 dB, (ref. @ 1 kHz). Low distortion at levels up to +27 dBu @ 20 Hz. Excellent Shielding – Mu Metal enclosures

Dual 117/234 VAC primary, 50/60 Hz. operation. 12 V series, 6 V parallel secondary.mary, 50/60 Hz. operation.

Open style, chassis mount transformers with a 115V 60Hz primary and a 28V center tapped secondary.

Hammond output transformer - replacement for Orange Rocker 30 Specifications: Part No. Pri Ohms Sec Ohms Amplifier Type Watts Bobbin/Paper Winding Equivalent To P-T1750ORF 6,000 C.T. 8, 16 Push-Pull 35 W Bobbin OT199SL

Studio Grade Impedance Matching, 1140 Series. ​Designed with Nickel alloy cores for high performance and Wide Bandwidth. Frequency Response: 20 Hz – 20 kHz ±0.35 dB, (ref. @ 1 kHz). Low distortion at levels up to +27 dBu @ 20 Hz. Excellent Shielding – Mu Metal enclosures

Dual 117/234 VAC primary, 50/60 Hz. operation. 234 V series, 117 V parallel secondary.