Transformers & Chokes

Fender

Fender® - Founded in Fullerton California by Leo Fender, Fender Musical Instruments Corp is the world's foremost manufacturer of guitars, basses, amplifiers and related equipment dating back to the 1940's.

Hammond

Hammond Manufacturing offers a full range of transformers, chokes and enclosures.

Triad Magnetics

Triad magnetics is a custom manufacturer of transformers and inductors.
P-T1750X-FENDER Transformer - Hammond, Output, replacement for Fender
  • Replacements for Fender Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $16.60
Save 10%
Originally: $18.44
P-T154-P-T156-X Filter Choke - Hammond, Open Bracket
Features
  • Economical "open bracket" - channel mount.
  • Tolerance of 15% on both inductance & resistance.
  • Inductances measured at rated D.C.
Starting at $11.72
Save 10%
Originally: $13.02
Note:
P-T155B: 6 mH / 2 A
P-T156M: 3 H / 100 mA
P-T156L: 5 H / 75 mA
P-T154G: 9 H / 40 mA (700 ohm)
P-T155C: 60 H / 8 mA
are special order items.
Note: some of these items are special order items.
P-T263-X Transformer - Hammond, High Voltage Plate & Filament, Vertical mount
  • Vertical Mount. For Horizontal Mount, see P-T263-Z
  • Primary 115 VAC, 60 Hz. - except as noted
  • Enclosed, 4 hole, chassis mount.
  • Minimum 6" long leads.
  • Units can be run full wave bridge or full wave C.T.
  • Class A insulation (105 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • Conservative designs - CSA certified (209651).
Starting at $45.05
Save 10%
Originally: $50.06
P-T290-FENDER-120 Transformer - Hammond, Guitar Amplifier, replacement for Fender, 120 V
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.
Starting at $32.62
Save 10%
Originally: $36.25
P-T166X-6D3 Transformer - Hammond, Low Voltage / Filament, Open, 6.3 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 6.3 C.T.
  • Center tapped secondary.
  • Open style, channel bracket, two hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C).
  • Hi-Pot test of 2,000 V RMS.
  • UL listed (# E50394) & CSA certified (# LR3902).
Starting at $9.88
Save 10%
Originally: $10.98
Note:
P-T166J6: 1 A
P-T166K6B: 1.2 A
are special order items.
Note: some of these items are special order items.
P-TF37099 Transformer - Fender®, Reverb, for Pro Reverb
Original Fender® reverb driver for Pro Reverb. Replacement for #037099. Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
$8.95
P-TF36958 Transformer - Fender®, Power, Hot Rod Deluxe
Fender Original Hot Rod Deluxe Power Transformer. Equivalent to #036958.



Specifications



Primary
120 VAC @ 60 Hz (Black - White)


Secondary 1 (Red - Red)
495 VDC unloaded, 440 VDC @ 65.7 mA DC, 388 VDC @ 200 mA DC


Secondary 2 (Brown - Brown)
53.6 VAC @ 1.58 A AC


Secondary 3 (Green - Green)
6.6 VAC @ 3.75 A AC


Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
$58.95
P-T261X6 Transformer - Hammond, Plate & Filament or Bias, 6.3 V auxiliary
  • Primary 115 VAC, 60 Hz.
  • Designed for small power or bias supplies, test equipment, preamps etc.
  • Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
  • Economical , two hole, channel bracket, chassis mount.
  • Minimum 5" long leads.
  • Convenient 6.3 filament/auxiliary winding.
Starting at $30.48
Save 10%
Originally: $33.87
P-T1650X Transformer - Hammond, Tube Output, Push-Pull
  • Designed for push-pull tube output circuits.
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Starting at $76.73
Save 10%
Originally: $85.25
P-T1750X-MARSHALL Transformer - Hammond, Output, replacement for Marshall
  • Replacements for Marshall Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $33.75
Save 10%
Originally: $37.50
P-TF50438 Transformer - Fender®, Output, Hot Rod Deluxe and Blues Deluxe
Fender Original Hot Rod Deluxe and Blues Deluxe output transformer. 40 watts. Equivalent to #050438.
$41.50
P-T125X Transformer - Hammond, Universal Push-Pull
  • Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
  • Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
  • Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
  • Tables provided with transformer listing 90 pre-calculated impedance ratios.
Starting at $33.14
Save 10%
Originally: $36.82
P-T125XSE Transformer - Hammond, Universal Single Ended
  • Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits.
  • Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE).
  • For push-pull output use, see P-T125A - optimized for push-pull tube output circuits.
  • Open style with minimum 12" long primary & secondary leads leads.
  • All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C.
Starting at $41.26
Save 10%
Originally: $45.84
P-C194X Choke - Hammond, replacement for Marshall amps
Features:
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Inductances measured at rated D.C. current.
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
Starting at $19.93
Save 10%
Originally: $22.14
P-TN-68X Transformer - Isolation, 50 VA, 115V, 435 mA, 2 x 115V
An Isolation Power Transformer for isolating equipment from direct connection to the power line. The transformer is constructed with non-concentrically wound coils. The primary and secondary are wound on separate arbors, then assembled on a laminate core side-by-side separated by insulation. This prevents electrical connection, under normal or overload conditions, between the primary and secondary windings.
$15.95
P-TF49969 Transformer - Output, Replacement for Blues Junior, 15 W
Fender Original Blues Junior output transformer.
Equivalent to #049969.
15 watts.
$25.15
P-T166X-2D5 Transformer - Hammond, Low Voltage / Filament, Open, 2.5 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 2.5 C.T.
  • Center tapped secondary.
  • Open style, channel bracket, two hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C).
  • Hi-Pot test of 2,000 V RMS.
  • UL listed (# E50394) & CSA certified (# LR3902).
Starting at $14.80
Save 10%
Originally: $16.44
P-TF49967 Transformer - Fender®, Power, Blues Junior, 15 W
Fender Original Blues Junior Power Transformer. Equivalent to #049967.
$50.95
P-T193X Filter Choke - Hammond, D.C. choke, Enclosed
  • Enclosed, 4-hole mount chokes
  • Tolerance of 15% on both inductance & resistance.
  • Inductances measured at rated D.C. current.
  • Minimum 8" long leads.
  • Units will exhibit less inductance at slightly higher currents or more at lower currents.
  • Perfect for high voltage power supply filtering, case matches power transformers & tube audio output transformers.
  • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
  • For more sizes and voltages (open - bracket mount type) - see P-T154-P-T156-X
  • Operating temperature range is -40C to 85C
Starting at $34.78
Save 10%
Originally: $38.65
P-T300-X Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount
  • Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
    • NOTE: units are designed to operate with BOTH primary windings engaged.
    • See primary wiring information under resources.
  • Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
  • Highpot tested: 2,000 VAC
  • Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
  • Windings: Concentric wound for low stray field and low noise.
  • Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
  • Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
  • Conservative designs - CSA certified (209651).
Starting at $63.20
Save 10%
Originally: $70.22
P-T124X Transformer - Hammond, Audio Interstage, 5 Watt
  • Designed for general purpose or replacement use in push-pull or phase inverter tube driver circuits.
  • Should not be used for single ended applications. They have no gap for DC bias current present in SE mode.
  • Open style with minimum 5" long primary leads.
  • Minimum frequency response 150 Hz. - 15 Khz (+/- 1db max. ref. 1 Khz.) at full rated power.
  • Core material is Grain Oriented Silicon Steel.
Starting at $34.74
Save 10%
Originally: $38.60
P-T119DA Transformer - Hammond, Audio Interstage, 12 Watt
Developed in response to requests from the Collins Collectors Association"this is a matching audio transformer for older equipment with 600 ohm audio outputdriving modern speakers. Or for "classic" high impedance speakers used with newer equipmentsimply swap primary for secondary (ie...4 or 8 ohm input and 600 ohms out). Key Features Isolation unit: (i.e.
$27.14
Save 10%
Originally: $30.16
P-T166X-5 Transformer - Hammond, Low Voltage / Filament, Open, 5 VCT
  • Primary 115 VAC, 60 Hz.
  • Secondary 5 C.T.
  • Center tapped secondary.
  • Open style, channel bracket, two hole chassis mount.
  • Minimum 6" long leads.
  • Dual bobbin design - no electrostatic shield required.
  • Class B insulation (130 degrees, C).
  • Hi-Pot test of 2,000 V RMS.
  • UL listed (# E50394) & CSA certified (# LR3902).
Starting at $18.50
Save 10%
Originally: $20.56
P-T263-Z Transformer - Hammond, High Voltage Plate & Filament, Horizontal mount
  • Horizontal mount. For Vertical Mount, see P-T263-X
  • Primary 117 VAC, 50/60 Hz. - except as noted
  • Enclosed, 4 hole, chassis mount.
  • Minimum 6" long leads.
  • Units can be run full wave bridge or full wave C.T.
  • Class A insulation (105 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • Conservative designs - CSA certified (209651).
  • For Vertical Mount, see P-T263-X
Starting at $60.52
Save 10%
Originally: $67.25
Don't see what you're looking for? Send us your product suggestions!