Tools

S-T202 Understring Radius Gauges - 9 Sizes, for Saddle Adjustments
Our low profile aluminum understring radius gauges have a precision radiused top and bottom for accurate measurement. The slim shape allows you to take measurements of several radii without removing the strings on your guitar.
  • Obtain accurate measurements of your instrument's fretboard radius using the bottom radius of the gauge. The bottom radius can also be used to set pickup polepiece height to the string radius.
  • Use the top radius of this gauge to determine the proper height adjustment for the bridge saddles.
  • The following gauges are included in this set: 7.25" 9.5" 10" 12" 14" 15" 16" 17" 20"
$14.00
S-TETCC Soldering iron tip - Weller, sloped, ⅛", for WES51
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWES51.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$4.95
S-T206 Fret Puller - Narrow Jaws
A specialized tool for cleanly pulling out frets. The narrow jaws are designed specifically to allow for a clean grip on frets.
$7.95
S-T205 Fingerboard Guards - 2 Sizes
Designed to protect the fingerboard when doing work on your frets. Comes with 2 sizes (dimension on either side of the fret gap): 1/4" 3/8"
$4.25
S-T214-X Fret Files - for Filing Fret Crowns
Solid steel crowning files with dual cutting edges for precision fret crowning. These should be in any luthier’s tool kit!
  • Made of solid steel
  • Soft rubber coating on the handle
  • Double sided (both sides are the same size)
  • 4-3/16” cutting surface
  • Available in three sizes to cover most fret sizes (small,medium,large)
Starting at $28.95
S-T227 Radius Gauges - 2 Gauges for 8 Radiuses
Solid, high quality stainless steel radius gauges. Use during fingerboard/fret shaping to accurately measure your progress and eliminate mistakes. Can also be used when shaping a nut/saddle or when setting string radius at the bridge. Great for working on compound radius necks. This is an essential tool for a luthier/tech’s bench.
  • Gauge 1 has 7.25", 9.5", 10", and 12" radiuses
  • Gauge 2 has 14", 15", 16", and 20" radiuses
  • Set of 2
$14.00
S-T156 Heat Sink - dissipate heat during soldering
Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.
$1.75
S-T806 The Nibbler - cutter for square holes
Instructions
  • Simply drill 3/8" hole insert cutting head and compress handles.
  • Gives you the ability to make square holes for fuse holders, special connectors displays etc.
  1. Material to be nibbled is placed in the gap between the punch and blade channel.
  2. By squeezing the handles together, the punch will move down into the channel, cutting out a slug of metal.
  3. A scribe line can be followed by looking down on work in this position.
$6.95
On Backorder
S-T210-X Fret/Fingerboard Leveler - for Flat Frets
Fret/Fingerboard leveler (1" x 2" in either 8" or 16" length). Use self-adhesive sandpaper (choosing the appropriate sand paper grit size for the job at hand) and attach it to the one inch surface of this steel beam which has been precision ground for flatness.
Starting at $11.95
S-T235 Precision Router Base - Support for Dremel Tool
A sturdy, adjustable-height support for Dremels.
$49.95
S-T9338 Burnishing Tool - GC Electronics, ¼" wide, steel
Stainless steel strip, microscored to an ultrafine file surface. Remove oxide and corrosion on contacts made of platinum, paladium, moybdenum, gold, tungsten, and silver.
$3.25
S-T203 String Spacing Ruler - Steel
Get accurate string spacing without the use of complicated tools with this easy-to-use String Spacing Ruler. "Mark outer string locations with pencil lines (high and low E strings on guitars), usually about 1/8" in from fingerboard edges. Turn ruler over (use marked side). With wide spacing toward bass side, narrow spacing toward treble side, find group of marks (six for guitar) which best fit your two pencil lines. Use a razor knife or thin mechanical pencil to mark the string positions through the ruler's slots.
$19.95
S-T204 Wrench - Steel, Multi-Spanner
A small, easily-portable tool designed for quick adjustments of various instrument parts (including nuts and thumb wheels), from potentiometers and pickup switches to tuning machines. One end is designed for loosening, the other is designed for tightening. The device has been chamfered and polished to avoid damage to your instrument when used.
$9.00
S-T229-X Two-Way Sanding Block - for Fret Sanding
Two-way sanding block for sanding frets at two sizes. Multiple options are available. Sandpaper not included.
Starting at $15.95
S-T212-E Nut Files - Double Edge, for Electric Guitars, 3 Sizes
Double edge nut files featuring popular electric guitar gauges specially designed for slotting nuts. This set of three files will cover the work of six and cuts a smooth round bottom slot. Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4” cutting edge
  • 6 gauges: .010"/ .026-.013"/ .036"-.017"/ .046"
  • Set of 3 files
  • Made In Japan
$60.95
S-T1715 Staking Tool - for Eyelets and Turrets
Turret staking tool.
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$9.95
S-T207 Feeler Gauge - 20 Sizes
Set of 20 feeler gauges to measure gap widths.
Includes:
  • (.0015" / .04 mm)
  • (.002" / .05 mm)
  • (.0025" / .06 mm)
  • (.003" / .08 mm)
  • (.004" / .10 mm)
  • (.005" / .13 mm)
  • (.006" / .15 mm)
  • (.008" / .20 mm)
  • (.010" / .25 mm)
  • (.012" / .30 mm)
  • (.014" / .35 mm)
  • (.016" / .40 mm)
  • (.018" / .45 mm)
  • (.020" / .50 mm)
  • (.022" / .55 mm)
  • (.024" / .60 mm)
  • (.026" / .65 mm)
  • (.028" / .70 mm)
  • (.030" / .75 mm)
  • (.032" / .80 mm)
$8.25
S-T228X Fret Polishing Rubber - Erases Fine Scratches & Marks
Make your frets shine with this fret polishing rubber. Erases fine scratches and marks. Set of 2. Available in 1000 (tan), 400 (red), or 180 (blue) grit.
Starting at $10.00
S-T212-B Nut Files - Double Edge, for Bass Guitars, 3 Sizes
Double edge nut files featuring popular bass guitar gauges specially designed for slotting nuts. This set of three files will cover the work of six and cuts a smooth round bottom slot.
Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4” cutting edge
  • 6 gauges: .045" / .085"- .065" / .105"- .075" / .130"
  • Set of 3 files
  • Made In Japan
$67.00
S-T8454 Alignment Kit - GC Electronics, for color TVs
Contains 6 different tools for all standard adjustments. Tools are Delrin with the exception of the potentiometer adjustment tool which is Nylon.
Tools are:
  • 8282 Zenith type Hex/Screwdriver
  • 8606 5" Hex wrench
  • 9091 Hex iron core tool
  • 9300 5" Double sided hex tool
  • 9304 Hex screwdriver combination
  • 8608 Potentiometer Adjustment Tool
$7.95
S-TETR Soldering iron tip - Weller, 1.6mm, screwdriver, for WES51
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWES51.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$4.95
S-T9004 Solder - Kester, ~\frac{60}{40}~, 44 Flux, 66 Core, .031 Dia, .5 OZ
Kester 44 60/40 rosin core type. .031" diameter, 0.5 oz
$5.78
S-T237 Fret Rocker - for Identifying Uneven Frets
Fret rocker luthier tool. Four precision ground flat edges having lengths: 4.0”, 3.0”, 2.0” and 1.3”. Perfect for finding the source of fret buzz. Place the flat edge over three frets at a time and try to rock the tool. If the tool rocks, you’ve located the uneven fret.
$8.75
S-T18-530 Alignment Kit - GC Electronics, for CB
Contains
  • 5009 Duplex no-metal screwdriver
  • 5097 K-tran tool
  • 8271 core aligner
  • 8282 Zenith alignment tool
  • 9091 hex iron core tool
  • 9440 transistor tool
  • 8276 Duplex aligner
  • 9304 double end tool
$15.60
Don't see what you're looking for? Send us your product suggestions!