Tools

S-T301 Power String Winder - Duck's Deluxe, Colors May Vary
Fits any cordless screwdriver. One size for: guitars, bass, banjos, mandolins, steel guitars, dobors, jazz boxes, etc.
$3.95
S-T251 Neck Support - 2-Way, For guitar
2-Way Neck Support for guitars. This natural wood, swing design neck support is great for any guitar shop front counter or repair bench and can be used for inspection or repairs of different sized guitars/basses with ease. No need for separate neck supports when switching between acoustic and electric guitars!
  • 2 way adjustable height is compatible with acoustic and electric guitars/basses
  • Large (15cmx15cm) square base keeps the guitar stable and steady during repair
  • Natural cork used at guitar contact points.
$55.00
S-T263 Knob & Bushing Puller - for Easy Removal From Guitar
Knob and bushing puller. Has a rubberized bottom rim for protecting the guitar’s surface while removing knobs and tailpiece stud bushings. Includes (6) bolts and (2) flat washers for pulling various bushing threads: • 5/16-20 • 5/16-24 • 5/16-18 • 10-32 • M6 x 1.0 • M5 x 0.8
Roughly 0.65" clearance between the bottom of the knob and the top of the guitar required for knob puller attachment.
$37.00
S-T237 Fret Rocker - for Identifying Uneven Frets
Fret rocker luthier tool. Four precision ground flat edges having lengths: 4.0”, 3.0”, 2.0” and 1.3”. Perfect for finding the source of fret buzz. Place the flat edge over three frets at a time and try to rock the tool. If the tool rocks, you’ve located the uneven fret.
$8.75
S-T203 String Spacing Ruler - Steel
Get accurate string spacing without the use of complicated tools with this easy-to-use String Spacing Ruler. "Mark outer string locations with pencil lines (high and low E strings on guitars), usually about 1/8" in from fingerboard edges. Turn ruler over (use marked side). With wide spacing toward bass side, narrow spacing toward treble side, find group of marks (six for guitar) which best fit your two pencil lines. Use a razor knife or thin mechanical pencil to mark the string positions through the ruler's slots.
$19.95
S-TGTBAS1 Bass Player Tech Kit - CruzTOOLS, GrooveTech
Not wanting to leave bass players out, we developed an alternate kit optimized for low-enders. The hex key set is matched to virtually all bass makes, and the string winder has been removed to save a couple of bucks. Like its guitar brethren, the GrooveTech Bass Kit has top-shelf tools that are lifetime guaranteed, and stored in a pouch that will fit into most gig bags. An Easy Setup Guide will make you comfortable with truss rod, action, pickup, and intonation adjustment.
$59.95
S-T202 Understring Radius Gauges - 9 Sizes, for Saddle Adjustments
Package of 9
Our low profile aluminum understring radius gauges have a precision radiused top and bottom for accurate measurement. The slim shape allows you to take measurements of several radii without removing the strings on your guitar.
  • Obtain accurate measurements of your instrument's fretboard radius using the bottom radius of the gauge. The bottom radius can also be used to set pickup polepiece height to the string radius.
  • Use the top radius of this gauge to determine the proper height adjustment for the bridge saddles.
  • The following gauges are included in this set: 7.25" 9.5" 10" 12" 14" 15" 16" 17" 20"
$14.00
S-F504X Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick Cyanoacrylate
Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
  • Extra thick, gap filling consistency
  • 10-25 second cure time
  • For looser fitting applications where a low viscosity glue is required
  • Available in 1oz. and 2oz. sizes

WARNING*: These products are eye and respiratory irritants. Product can bond skin instantly.
Starting at $4.95
Save 10%
Originally: $5.50
S-F502X Adhesive - Bob Smith Industries, Insta-Cure + Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $4.95
Save 10%
Originally: $5.50
S-T235 Precision Router Base - Support for Dremel Tool
A sturdy, adjustable-height support for Dremels.
$49.95
P-PC-BB400 BreadBoard - Solderless, 400 point pattern
Solderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.
$4.75
S-TGTGTR1 Tech Kit - CruzTOOLS GrooveTech, for Guitar Player
Guitar players may know a little about truss rods and action, but few actually attempt adjustment. That's a shame, because a good setup will improve your performance. The GrooveTech provides everything you need to work on your guitar, plus an Easy Setup Guide that takes the mystery out of the process. Eleven hex keys are color-coded gold for metric and black for inch sizes, and long pattern for easy access. All truss rod sizes are ball end. Also included is a thickness gauge, ruler, capo, cutters, string winder, and 6-in-1 screwdriver.
$59.95
P-PC-SB404 BreadBoard - Solderable PCB, 400 point pattern
Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts.
The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
$4.50
S-F500X Adhesive - Bob Smith Industries, Insta-Cure Super Thin
Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
  • Water-thin consistency
  • 1-3 second cure time
  • For tight fitting applications
  • Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
Starting at $4.95
Save 10%
Originally: $5.50
S-B300 Electronic Component Storage Box - large
This electronic component storage box works great for storing caps, pots, resistors and other electronic components. 10 different compartments, made of plastic, measures 8.25" x 4.25".
$10.95
S-B301 Electronic Component Storage Box - small
This electronic component storage box works great for storing caps, pots, resistors and other electronic components. 8 different compartments, made of plastic, measures 5" x 3.375".
$6.25
S-T9000X Solder - Kester 44, 1 lb spool
(60/40 Rosin Core) - ..031" or .050" Diameter, 1 lb Spool, contains lead alloy.
Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades.
An outstanding performance feature of this flux is the “instant-action” wetting behavior.
$31.95
S-T170M Cutters - Xcelite, Shearcutter, General Purpose
5" Overall Length, 3/4" Jaw Length. Great for cutting wire and component leads, etc. Product Features:
  • Low profile, general-purpose cutter
  • Superior blade by-pass shear cutting action
  • Better cuts with half the effort
  • Greatly reduced mechanical shock delivered to the work
  • Features red grips
  • Flush cuts soft wire up to 20 AWG (0.8mm)
$10.25
S-T1715 Staking Tool - for Eyelets and Turrets
Turret staking tool.
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$9.95
S-TST1 Soldering iron tip - Weller, screwdriver ~\frac{1}{16}~", for WLC100/WP35
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.
  • ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
  • Precision ground copper tips are plated with iron, nickel and chromium
  • ST1 - .062" / 1.58 mm wide Screwdriver tip
  • Tinned with Lead Free alloy
$4.25
S-TST3 Soldering iron tip - Weller, screwdriver ⅛", for WLC100/WP35
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.
  • ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
  • Precision ground copper tips are plated with iron, nickel and chromium
  • ST3 - .125" / 3.17 mm wide Screwdriver tip
  • Tinned with Lead Free alloy
$5.50
S-TST7 Soldering iron tip - Weller, conical, for WLC100/WP35
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.
  • ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
  • Precision ground copper tips are plated with iron, nickel and chromium
  • ST7 - .031" / 0.79 mm diameter Conical tip
  • Tinned with Lead Free alloy
$4.95
S-T806 The Nibbler - cutter for square holes
Instructions
  • Simply drill 3/8" hole insert cutting head and compress handles.
  • Gives you the ability to make square holes for fuse holders, special connectors displays etc.
  1. Material to be nibbled is placed in the gap between the punch and blade channel.
  2. By squeezing the handles together, the punch will move down into the channel, cutting out a slug of metal.
  3. A scribe line can be followed by looking down on work in this position.
$6.95
P-PC-PAD1 PadBoard - Size 1, Double Sided, Plated Holes
Prototyping circuit board that has a general purpose pad-per-hole pattern making it great for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be easily soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. An anti-tarnish coating protects the copper for a long shelf-life and provides easy soldering.
For fastening your project to a surface see our adhesive standoffs (S-H190-X)
Features:
  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
  • 31 x 19 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
  • Size 1 = 1.97 x 3.15in (50 x 80mm), 1/16" thick (1.6mm)
$2.95
Don't see what you're looking for? Send us your product suggestions!