Tools

P-PC-SB400 Breadboard - Solderable PCB, 3.00” x 1.90”
The SB400 Solderable PCB BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. The SB400 has the same pattern and spacing as a standard 400 connection point BB400 solderless plug-in breadboard. It has a standard 5-hole strip for each IC pin, just like solderless breadboards plus 4 power rails. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The SB400 has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used. BPS prototyping boards use high-quality FR4 glass epoxy PCBs for long life, with an anti-tarnish protective coating for easy soldering.
$4.95
P-PC-ST2 StripBoard - Single Sided, 3.94” x 3.15”, Mounting Holes
ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$5.50
P-PC-PAD2 PadBoard - Double Sided, Plated Holes, 3.94” x 3.15”, Mounting Holes
The PadBoard-2 prototyping circuit board has a general purpose pad-per-hole pattern which is good for analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. Features
  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 31 x 39 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
  • Size2 = 100 x 80mm (3.94 x 3.15in), 1/16" thick (1.6mm)
$6.85
P-PC-ST3U StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$9.95
P-PC-PAD3U PadBoard - Double Sided, Plated Holes, 6.30” x 3.94”, Mounting Holes
The PadBoard-3U prototyping circuit board has a general purpose pad-per-hole pattern which is good for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. The PCB accepts a 96 pin DIN-41612 VME connector for backplane or board-to-board applications. Holes for ejector latches are provided. Features
  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$12.95
S-TCFOIL-X Tape - Copper Foil, for Shielding, 98ft Length Roll
Conductive copper foil tape for shielding guitar cavities, amplifier cabinets, or elsewhere. This tape features a strong adhesive backing and soldering directly to the surface is easy and results in a strong bond. Sold in 98ft rolls.
Starting at $54.95
S-T-MAGNETIZER Tool - Magnetizer / Demagnetizer
Small magnetizer / demagnetizer for use with hand tools. Simply pass a tool such as a screwdriver through the square hole to magnetize the tool and pass it through the u-shaped channel to demagnetize the tool. Note: When passing through the square cutout to magnetize a tool, be sure to keep the tool from touching the four walls of the magnetizer to ensure a proper magnetization. When using the demagnetizer, the tool can touch the plastic of the channel.
$3.95
S-T-IC-PULLER Tool - IC Extractor / Puller
Hand-held IC extractor for use on a variety of chip sizes. The metal ends hook beneath the chip. When a pinching force is applied to the bends of the plastic, the metal ends clamp onto the chip and pull upward uniformly to avoid bending pins. This tool can be used on widths of 7mm and up.
$3.95
S-T-TIP-CLEANER Tip Cleaner - Wire Type for Soldering Irons
Coiled metal wire type tip cleaner for use with soldering irons. The metal wire cleaner requires no water which reduces temperature drops in the tip compared to using a sponge. The black metal holder is dome shaped to reduce airborne solder droplets when cleaning. The holder has a detachable top and bottom to easily empty when necessary.
$8.59
S-T-SOLDER-STAND Tool - Solder Spool Stand
All-metal solder spool stand with a large metal roller for a smooth reel out. This stand features a handle as well as an eyelet that holds the solder line in a static position for ease of use. Extremely useful for making your soldering jobs quick and easy!
$7.95
S-T1714 Staking Tool - For Small Eyelets
Staking tool for small eyelets such as S-HEYE-B. Directions:
  • Drill hole using #42 drill bit
  • Insert eyelet
  • Flip board over onto a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$13.95
S-T56626 Hex Key Set - Allen®, Fold-up, 7 Piece, Metric
High quality fold-up set of metric hex keys from Allen®. This set is great for easy storage and eliminates misplacing keys.
$11.95
S-T56622 Hex Key Set - Allen®, Fold-up, 9 Piece, SAE
High quality fold-up set of SAE hex keys from Allen®. This set is great for easy storage and eliminates misplacing keys.
$11.95
S-T56606 Hex Key Set - Allen®, Long Arm, 9 Piece, Metric
High quality set of long arm metric hex keys from Allen®. This set includes 9 keys in a hinged holder for easy storage.
$11.50
S-T56603 Hex Key Set - Allen®, Long Arm, 13 Piece, SAE
High quality set of long arm SAE hex keys from Allen®. This set includes 13 keys in a hinged holder for easy storage.
$12.99
S-T-RX Tool - Precision Devices, Lead Former, Various Sizes
High quality, made in USA lead formers. These are great tools for bending component leads to fit various footprints. The radiused ends provide a right angle bend that does not stress the metal lead. These lead formers are made of high impact ABS plastic.
$4.95
P-GWRENCH-3 Allen wrenches - set of three sizes
Package of 3
Allen wrench set of three: 2.5mm, 3mm, 4mm
$4.25
S-B300-X Storage Box - for electronic components
This electronic component storage box works great for storing caps, pots, resistors and other electronic components. Made of plastic.
Starting at $6.25
S-MAFGEN Generator - Lodestar, Audio Frequency
The oscillation frequency range of this audio generator is between voice frequency band and super voice frequency band. Square and sine wave. 10K ohm input impedance, 10 V rms maximum input voltage. 600 ohm output impedance. Equipped with synchronized input terminals, enabling the high power output signas to be accurately controlled by small signals. comes with test lead and ground lead. 5.9" high x 9.8" wide x 5.1"deep.
$184.95
S-MRFGEN Generator - Lodestar, RF Signal generator
Compact solid state RF signal generator designed for the hobbyist, service bench and technical instruction. The generator is most suited for checking and aligning the IF circuit and tuners in AM, FM, and TVs. 100 kHz to 150 MHz in 6 bands and up to 450 MHz on third harmonics.
Features:
  • Wide frequency range- 100 Khz to 150 MHz
  • With 1 KHz oscillator purpose of modulation
  • High Stability
  • Output control- 0dB/-20dB/-40dB and fine adjuster
  • Frequency accuracy + or - 5%
  • RF output- 100mV rms appx. (up to 35MHz unloaded)
  • Output control- High-low switch, fine adjust
  • Audio output 1 KHz min., 2V rms
  • Modulation: Internal: 1 KHz (AM) 30% appx., External: 50 Hz ~ 20 KHz at <1V rms input
$178.00
S-T100X Wire Stripper / Cutter - Xcelite, 5", with Cushion Grip Handle
5" wire stripper & cutter with cushion grip handles. Features:
  • Cuts and strips both solid and stranded wire cleanly, neatly.
  • Adjustable screw stop for different wire sizes.
  • Hardened with ground blades.
  • Red plastic-coated cushion grip provides maximum leverage.
  • Strips 8AWG - 22AWG wire.
$15.75
S-T105SCGV Wire Stripper / Cutter - Xcelite, 6", with Spring and Lock
6" stripper, cutter with spring and lock, cushion grip handles, carded. Features
  • Wire cutting and stripping edges conveniently located in front of pivot
  • Allows use in tight places
  • Needle nose pliers add wire pulling and bending capabilities
  • Scissors-action stripper for cleaner, faster and more accurate stripping
  • Serrated edge
  • Includes work-speeding automatic spring and lock
  • Red cushion grip handle provides maximum leverage
  • For copper and aluminum wire 10 - 22 AWG
$26.50
S-T156 Heat Sink - dissipate heat during soldering
Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.
$1.75
S-T170M Cutters - Xcelite, Shearcutter, General Purpose
5" Overall Length, 3/4" Jaw Length. Great for cutting wire and component leads, etc. Product Features:
  • Low profile, general-purpose cutter
  • Superior blade by-pass shear cutting action
  • Better cuts with half the effort
  • Greatly reduced mechanical shock delivered to the work
  • Features red grips
  • Flush cuts soft wire up to 20 AWG (0.8mm)
$13.95
Don't see what you're looking for? Send us your product suggestions!