Dunlop is a manufacturer of picks, pedals, and accessories for over 50 years.

Bob Smith Industries

Super glues and adhesives made in the USA.
S-F500X Adhesive - Bob Smith Industries, Insta-Cure Super Thin
Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
  • Water-thin consistency
  • 1-3 second cure time
  • For tight fitting applications
  • Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
Starting at $5.50
S-F502X Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $5.50
S-F504X Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick
Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
Starting at $5.50
S-F506X Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray
Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
  • Convenient pump spray (2oz.
Starting at $5.95
S-F508X Adhesive - Bob Smith Industries, Extender Tip for Glue
Package of 6
Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application.
  • Helps focus glue stream
  • Works with all three CA glue viscosities
  • Package of 6
Starting at $5.95
S-T304 Magnetic Parts Tray - Dunlop, System 65
Keep all of your parts in one place with this magnetic tray. 4” diameter across the top rim and 2.5” diameter on the base.
S-T306 Flashlight - Dunlop, System 65 gig
The Dunlop System 65 Gig Light is a high lumen, road ready flashlight. At 3.7” in length it easily fits in a gig bag or pocket and can be safely secured with its metal belt clip. This flash light has three different modes that can be accessed by lightly tapping the power switch: high beam, low beam, and strobe. The beam can also be focused by adjusting the lens providing up to 100 yards of visible light with a tight focus. This waterproof flashlight runs on a single AA battery which is included.
S-T311 Screwdriver - Dunlop, System 65
The Dunlop System 65 Screwdriver is the perfect small sized tool for a gig bag or case. The four bits include two different Phillips heads and two different flat heads which can cover almost any screw used on guitars and basses.
S-T312 String Cutters - Dunlop, System 65
The Dunlop System 65 String Cutter can cut through any strings. It will cut through .130” thick bass strings just as easily as a .010” guitar string. This is a great tool to keep nearby, easily fitting in a case or gig bag.
S-T307 Multi Tool - Dunlop, System 65
The Dunlop System 65 Multi Tool is a compact tool that can cover the gamut of setup work for guitars and basses. Whether it’s a pickup height issue, truss rod adjustment, or a tweak in the action, this multitool can do it all.
S-T309 String Action Gauge - Dunlop, System 65
The Dunlop System 65 String Action Gauge is a precision measurement tool for setups and adjustments. The gauge includes both metric and imperial measurements on opposite sides.
S-T308 Uni-Wrench - Dunlop, System 65
The Dunlop System 65 Uni-Wrench is great tool for tightening and loosening any threaded nut on a guitar or bass. This includes pots, jacks, bridge posts, rounded knurled nuts on selector switches and more.
S-T303 Guitar Setup Mat - Dunlop, System 65
Work on your guitars without the worry of scratching the finish. This thick neoprene mat measures 17 7/8” x 23 ¾”. The tight webbing on the surface ensures no marring and helps keep debris from sticking to the mat.
S-T310 Fret Collars - Dunlop, System 65
Package of 2
The Dunlop System 65 Fret Collars include everything you need for a quick fret polish without the need for taping the entire neck. Two sizes of flexible steel collars are included, 0.125 and .080.
S-T300 Neck Cradle - Dunlop, Maintenance Station
The self-aligning cradle rotates to provide full support to the back or front of the neck for increased stability during repairs or maintenance work.
Don't see what you're looking for? Send us your product suggestions!