Tools

S-T156 Heat Sink - dissipate heat during soldering
Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.
$1.75
S-TWCC104 Sponge - for Soldering Station
Replacement sponge for the Weller WLC 100 soldering station ( S-TWLC100 ) . Keep your iron tip clean using this genuine Weller replacement sponge. Cleaning a hot soldering iron on a damp sponge causes the solder to contract at a contrasting rate to the soldering iron, helping to remove any solder stuck to the tip. Always be sure the sponge is merely damp rather than soaked in water.
$2.60
S-T22-X Solder wick - GC Braid, multiple sizes
5 feet Long. Great for removing solder from printed circuit boards.
Starting at $3.50
S-T302 Bulb - Solder Sucker
Handheld suction type solder remover.
$3.95
S-T205 Fingerboard Guards - 2 Sizes, for protecting frets
Package of 2
Designed to protect the fingerboard when doing work on your frets. These shields are indispensable when doing any sort of fret work. Being only .010” thick they can bend to accommodate and fingerboard radius. Made of 304 spring stainless steel.
Comes with 2 sizes: 3-1/8" x 7/8" x .010" - 1/4 inch protection on either side of the fret, 3-1/8"" x 0.59" x .010"" - 3/8 inch protection on either side of the fret
$4.25
S-T5000 Jumper Test Lead Set - Clip 35mm, Total Length 24", 22AWG
Package of 10
Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green
$4.40
S-TST1 Soldering iron tip - Weller, screwdriver ~\frac{1}{16}~", for WLC100 / WP35
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.
  • ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
  • Precision ground copper tips are plated with iron, nickel and chromium
  • ST1 - .062" / 1.58 mm wide Screwdriver tip
  • Tinned with Lead Free alloy
$4.50
S-TST7 Soldering iron tip - Weller, conical, for WLC100 / WP35
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.
  • ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
  • Precision ground copper tips are plated with iron, nickel and chromium
  • ST7 - .031" / 0.79 mm diameter Conical tip
  • Tinned with Lead Free alloy
$4.95
S-T247-X Sandpaper - Kovax rolled, 1400 x 64 mm, Self-Adhesive
1.4m, Self adhesive type, 64mm width for S-T229-X sanding blocks.
Starting at $5.25
S-TPTA7 Soldering iron tip - Weller, screwdriver, for WTCPT, 700F
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Screwdriver Tip for TC201 Series Iron
  • PTA7 - 1.6mm / 0.063" diameter screwdriver tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
$5.39
S-TPTP7 Soldering iron tip - Weller, conical, for WTCPT
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Conical Tip for TC201 Series Iron
  • PTP7 - 0.79mm / 0.031" diameter conical tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
$5.39
S-F500X Adhesive - Bob Smith Industries, Insta-Cure Super Thin
Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
  • Water-thin consistency
  • 1-3 second cure time
  • For tight fitting applications
  • Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
Starting at $5.50
S-F502X Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $5.50
S-F504X Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick
Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
Starting at $5.50
S-TST3 Soldering iron tip - Weller, screwdriver ⅛", for WLC100 / WP35
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.
  • ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
  • Precision ground copper tips are plated with iron, nickel and chromium
  • ST3 - .125" / 3.17 mm wide Screwdriver tip
  • Tinned with Lead Free alloy
$5.70
S-T9004 Solder - Kester, 60 / 40, 44 Flux, 66 Core, .031 Dia, .5 oz
Kester 44 60/40 rosin core type. .031" diameter, 0.5 oz
$5.78
S-THHM Tool - Helping Hand with Magnifier, 65mm, 2.5X
Magnifier with 2 ½" lens. Both clamps and magnifier can be removed. Great for precision work on circuit boards, solders and repairs. 6 ball joints for any angle. Simple to adjust thumb screws. Nickel plating fittings. Sturdy iron cast base. Alligator spring clips
$5.95
S-F506X Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray
Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
  • Convenient pump spray (2oz.
Starting at $5.95
S-F508X Adhesive - Bob Smith Industries, Extender Tip for Glue
Package of 6
Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application.
  • Helps focus glue stream
  • Works with all three CA glue viscosities
  • Package of 6
Starting at $5.95
S-TVBV Tool - Vacuum Base Vise, 40mm
Mini vise. Great for securing small, light-weight components like potentiometers, tube sockets and switches while soldering or de-soldering. Clamp opens to 40 mm max.
$6.95
S-T261 Fret Press Inserts - for Pressing Frets, Multiple Radiuses
Fret press inserts. 2.5” width brass inserts fit the S-T259-A and S-T260 fret press cauls. Used to press frets into guitar fret boards as an alternative to hammering.
$6.95
S-T7875B Desoldering pump tip - Weller, replacement for 7874B
Restore the performance of your desoldering pump by replacing the tip. Replacement for S-T7874B.
$6.98
S-CRSF-R80-X Soldering Flux - Caig, Deoxit, Rosin Flux
Low residue, no-spill. Thermal stability enabling excellent wetting and reduced carbonization at soldering temperature. No-clean flux can be removed by wiping with a cloth or with cleaning solvent. Nonflammable and non corrosive. Recommended for electrical and electronic soldering applications.
Starting at $7.15
S-T206 Fret Puller - Narrow Jaws, for removing frets
A specialized tool for cleanly pulling out frets. The narrow jaws are designed specifically to allow for a clean grip on frets. The special flush ground 1/2" jaws can easily bite the frets without damaging the fretboard.
$7.95
Don't see what you're looking for? Send us your product suggestions!