Tools

S-TCPS7 Springs - Xcelite, replacement for S-TCN255
Replacement spring for S-TCN255 (Xcelite curved nose pliers).
$1.00
S-T205 Fingerboard Guards - 2 Sizes, for protecting frets
Package of 2
Designed to protect the fingerboard when doing work on your frets. These shields are indispensable when doing any sort of fret work. Being only .010” thick they can bend to accommodate and fingerboard radius. Made of 304 spring stainless steel.
Comes with 2 sizes: 3-1/8" x 7/8" x .010" - 1/4 inch protection on either side of the fret, 3-1/8"" x 0.59" x .010"" - 3/8 inch protection on either side of the fret
$4.25
S-T247-X Sandpaper - Kovax rolled, 1400 x 64 mm, Self-Adhesive
1.4m, Self adhesive type, 64mm width for S-T229-X sanding blocks.
Starting at $5.25
S-F500X Adhesive - Bob Smith Industries, Insta-Cure Super Thin
Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
  • Water-thin consistency
  • 1-3 second cure time
  • For tight fitting applications
  • Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
Starting at $5.50
S-F502X Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $5.50
S-F504X Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick
Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
Starting at $5.50
S-F506X Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray
Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
  • Convenient pump spray (2oz.
Starting at $5.95
S-F508X Adhesive - Bob Smith Industries, Extender Tip for Glue
Package of 6
Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application.
  • Helps focus glue stream
  • Works with all three CA glue viscosities
  • Package of 6
Starting at $5.95
S-T806 The Nibbler - cutter for square holes
Instructions
  • Simply drill 3/8" hole insert cutting head and compress handles.
  • Gives you the ability to make square holes for fuse holders, special connectors displays etc.
  1. Material to be nibbled is placed in the gap between the punch and blade channel.
  2. By squeezing the handles together, the punch will move down into the channel, cutting out a slug of metal.
  3. A scribe line can be followed by looking down on work in this position.
$6.95
S-T261 Fret Press Inserts - for Pressing Frets, Multiple Radiuses
Fret press inserts. 2.5” width brass inserts fit the S-T259-A and S-T260 fret press cauls. Used to press frets into guitar fret boards as an alternative to hammering.
$6.95
S-T8454 Alignment Kit - GC Electronics, for color TVs
Package of 6
Contains 6 different tools for all standard adjustments. Tools are Delrin with the exception of the potentiometer adjustment tool which is Nylon.
Tools are:
  • 8282 Zenith type Hex/Screwdriver
  • 8606 5" Hex wrench
  • 9091 Hex iron core tool
  • 9300 5" Double sided hex tool
  • 9304 Hex screwdriver combination
  • 8608 Potentiometer Adjustment Tool
$7.95
S-T206 Fret Puller - Narrow Jaws, for removing frets
A specialized tool for cleanly pulling out frets. The narrow jaws are designed specifically to allow for a clean grip on frets. The special flush ground 1/2" jaws can easily bite the frets without damaging the fretboard.
$7.95
S-T207 Feeler Gauge - 20 Sizes, for measuring gaps / clearance
Package of 20
This precise set of 20 feeler gauges in the luthier's workshop can perform a wide variety of functions to measuring with string action to measuring the correct nut slot depths, fret slot width, string to fret clearances, and other hardware installation work, these ground steel feeler gauges are marked in both metric and imperial measurements for easy use.
$8.25
S-T237 Fret Rocker - for Identifying Uneven Frets
Fret rocker luthier tool. Four precision ground flat edges having lengths: 4.0”, 3.0”, 2.0” and 1.3”. Perfect for finding the source of fret buzz. Place the flat edge over three frets at a time and try to rock the tool. If the tool rocks, you’ve located the uneven fret.
$8.75
S-T234 String Spreader - for fret work without unstringing
Package of 2
Those of us who don’t want to fully remove that new set of strings to do some quick spot work on the fret board or nut will love this simple yet effective tool. Simply loosen your strings and place the string spreaders underneath the guitar neck. Bring the strings off the neck and latch them underneath the spreader's ends to allow for quick and easy fret-board work without the need to unstring your instrument. These string spreaders will quickly become a must have in your toolbox!
  • Make room for cleaning, polishing or spot work on frets without removing strings
  • Made of brass with a soft, finish safe, rubber coating
$8.95
S-T204 Wrench - Steel, Multi-Spanner, for guitar components
A small, easily-portable tool designed for quick adjustments of various instrument parts (including nuts and thumb wheels), from potentiometers and pickup switches to tuning machines. One end is designed for loosening, the other is designed for tightening. The device has been chamfered and polished to avoid damage to your instrument when used.
$9.00
S-T304 Magnetic Parts Tray - Dunlop, System 65
Keep all of your parts in one place with this magnetic tray. 4” diameter across the top rim and 2.5” diameter on the base.
$9.85
S-T1715 Staking Tool - for Eyelets and Turrets
Turret staking tool for use with our turrets (S-HTUR-AX, S-HTUR-BX, S-HTUR-P).
For anvil see S-T1717
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$9.95
S-T311 Screwdriver - Dunlop, System 65
The Dunlop System 65 Screwdriver is the perfect small sized tool for a gig bag or case. The four bits include two different Phillips heads and two different flat heads which can cover almost any screw used on guitars and basses.
$9.95
S-T228X Fret Polishing Rubber - Erases Fine Scratches & Marks
Package of 2
Make your frets shine with this fret polishing rubber. Erases fine scratches and marks. Set of 2. Because of the softness of the rubber, the polisher fits to fret arch perfectly and keeps the fingerboard damage to a minimum. Easy to cut for delicate fret work. This is a great rust remover and polisher!
Available in 1000 (tan), 400 (red), or 180 (blue) grit.
Starting at $10.00
S-T213 Nut File - Edge-Cut, for guitars
Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4.5” cutting edge
  • Double sided (both sides are the same gauge)
  • 10 gauges available
  • Sold individually*
  • Made In Japan

*See S-T213-SET for a set of all 10 sizes.
Starting at $11.50
S-T250 Scraper Set - 120mm x 44mm, Standard Set of 2
Package of 2
Luthier tool, set of 2 scrapers for wood working. 0.4mm thickness.
$11.50
S-TGTSC1 String Cutters - CruzTOOLS GrooveTech, for guitar and bass
CruzTOOLS developed the GrooveTech String Cutters specifically for Guitar and Bass strings. Guitar and bass strings are made of hardened stainless steel or nickel with thicknesses as high as 3mm. Ordinary diagonal cutters are designed for soft copper, and thus fail miserably when used on strings. GrooveTech String Cutters were developed specifically for this application, using a proprietary heat-treatment process. Despite its compact five-inch length, even “B” bass strings cut easily and your days of dented blades will be a thing of the past. Vinyl grips feel great in your hands.
$11.95
S-TGTTRX Truss Rod Driver - Cruz Tools, GrooveTech
Vintage-style truss rod nuts have long, thin slots and are made of unhardened steel, so normal slotted screwdrivers will cause damage – as evidenced on many vintage guitars and basses. Cruz Tools developed two screwdrivers specifically for this application. Proper adjustment involves removal of the neck for full nut access, and our Standard Driver provides firm contact over the entire slot width for damage-free adjustment. The Cheater Driver™ allows quick minor adjustment without removing the neck. Both have oversized handles with extra-long shafts for a firm grip and easy access.
$11.95
Don't see what you're looking for? Send us your product suggestions!