Tools

S-H190-X Standoff - 0.18", Adhesive
Low-profile adhesive standoffs with a 0.180" standoff height that securely attaches your PCB to a flat surface. The post inserts into a 0.125” mounting hole and includes a locking tab that secures the PCB when inserted. It can be used with 1/16” or 1/32” thick PCBs. The 0.6 x 0.6” square base is offset to allow the base to be underneath the board when the mounting hole is close to the PCB edge and the offset base provides a large sticking surface while permitting the PCB to be mounted in tight spaces or close to walls. This can be useful when working with small enclosures. High-quality 3M™ brand double-sided tape secures the standoff to a flat surface. These standoffs are available in packs of 8, 24, or 100 pieces Features:
  • Low profile 0.180" standoff height.
  • Offset base allows use when holes are close to the PCB edge.
Starting at $2.25
P-PC-ST1 StripBoard - Single Sided, Size 1, Uncut
Prototyping circuit board with a standard long strip pattern where tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads and the board has 0.1" hole spacing for DIP integrated circuits/ headers as well as other parts. Higher quality than traditional stripboard, the holes are drilled, not punched.
$2.95
P-PC-PAD1 PadBoard - Size 1, Double Sided, Plated Holes
Prototyping circuit board that has a general purpose pad-per-hole pattern making it great for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be easily soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. An anti-tarnish coating protects the copper for a long shelf-life and provides easy soldering.
For fastening your project to a surface see our adhesive standoffs (S-H190-X)
Features:
  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
  • 31 x 19 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
  • Size 1 = 1.97 x 3.15in (50 x 80mm), 1/16" thick (1.6mm)
$2.95
P-PC-PR1590B ProtoBoard - Fits 1590B, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590B die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590B enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190-X) Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 2 mounting holes.
  • PCB Size 2.05 x 4.05 in (52.1 x 102.9 mm)
$3.40
S-T205 Fingerboard Guards - 2 Sizes, for protecting frets
Package of 2
Designed to protect the fingerboard when doing work on your frets. These shields are indispensable when doing any sort of fret work. Being only .010” thick they can bend to accommodate and fingerboard radius. Made of 304 spring stainless steel.
Comes with 2 sizes: 3-1/8" x 7/8" x .010" - 1/4 inch protection on either side of the fret, 3-1/8"" x 0.59" x .010"" - 3/8 inch protection on either side of the fret
$4.25
P-PC-SB404 BreadBoard - Solderable PCB, 400 point pattern
Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts.
The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
$4.50
P-PC-BB400 BreadBoard - Solderless, 400 point pattern
Solderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.
$4.75
S-T247-X Sandpaper - Kovax rolled, 1400 x 64 mm, Self-Adhesive
1.4m, Self adhesive type, 64mm width for S-T229-X sanding blocks.
Starting at $5.25
P-PC-PR1590BB ProtoBoard - Fits 1590BB, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590BB die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590BB enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190-X). Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 4 mounting holes.
  • PCB Size 3.20 x 4.25 in (81.3 x 108.0 mm)
$5.50
S-F500X Adhesive - Bob Smith Industries, Insta-Cure Super Thin
Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended.
  • Water-thin consistency
  • 1-3 second cure time
  • For tight fitting applications
  • Available in 1oz. and 2oz. sizes

WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children!
Starting at $5.50
S-F502X Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $5.50
S-F504X Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick
Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
Starting at $5.50
S-F506X Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray
Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
  • Convenient pump spray (2oz.
Starting at $5.95
S-F508X Adhesive - Bob Smith Industries, Extender Tip for Glue
Package of 6
Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application.
  • Helps focus glue stream
  • Works with all three CA glue viscosities
  • Package of 6
Starting at $5.95
S-T261 Fret Press Inserts - for Pressing Frets, Multiple Radiuses
Fret press inserts. 2.5” width brass inserts fit the S-T259-A and S-T260 fret press cauls. Used to press frets into guitar fret boards as an alternative to hammering.
$6.95
S-T206 Fret Puller - Narrow Jaws, for removing frets
A specialized tool for cleanly pulling out frets. The narrow jaws are designed specifically to allow for a clean grip on frets. The special flush ground 1/2" jaws can easily bite the frets without damaging the fretboard.
$7.95
S-T207 Feeler Gauge - 20 Sizes, for measuring gaps / clearance
Package of 20
This precise set of 20 feeler gauges in the luthier's workshop can perform a wide variety of functions to measuring with string action to measuring the correct nut slot depths, fret slot width, string to fret clearances, and other hardware installation work, these ground steel feeler gauges are marked in both metric and imperial measurements for easy use.
$8.25
S-T237 Fret Rocker - for Identifying Uneven Frets
Fret rocker luthier tool. Four precision ground flat edges having lengths: 4.0”, 3.0”, 2.0” and 1.3”. Perfect for finding the source of fret buzz. Place the flat edge over three frets at a time and try to rock the tool. If the tool rocks, you’ve located the uneven fret.
$8.75
S-T234 String Spreader - for fret work without unstringing
Package of 2
Those of us who don’t want to fully remove that new set of strings to do some quick spot work on the fret board or nut will love this simple yet effective tool. Simply loosen your strings and place the string spreaders underneath the guitar neck. Bring the strings off the neck and latch them underneath the spreader's ends to allow for quick and easy fret-board work without the need to unstring your instrument. These string spreaders will quickly become a must have in your toolbox!
  • Make room for cleaning, polishing or spot work on frets without removing strings
  • Made of brass with a soft, finish safe, rubber coating
$8.95
S-T204 Wrench - Steel, Multi-Spanner, for guitar components
A small, easily-portable tool designed for quick adjustments of various instrument parts (including nuts and thumb wheels), from potentiometers and pickup switches to tuning machines. One end is designed for loosening, the other is designed for tightening. The device has been chamfered and polished to avoid damage to your instrument when used.
$9.00
S-W604X ZipWire - Jumper Cable Kit
Package of 120
The ZipWire™ Kit provides a convenient way to connect the signals in your projects. The wires can be unzipped for individual wires as needed and the color-coding can be used to organize power, ground and other signal types to keep your circuit organized. The rainbow colored ribbon cable provides the 10 standard electrical colors.
Starting at $9.50
S-T304 Magnetic Parts Tray - Dunlop, System 65
Keep all of your parts in one place with this magnetic tray. 4” diameter across the top rim and 2.5” diameter on the base.
$9.85
S-T228X Fret Polishing Rubber - Erases Fine Scratches & Marks
Package of 2
Make your frets shine with this fret polishing rubber. Erases fine scratches and marks. Set of 2. Because of the softness of the rubber, the polisher fits to fret arch perfectly and keeps the fingerboard damage to a minimum. Easy to cut for delicate fret work. This is a great rust remover and polisher!
Available in 1000 (tan), 400 (red), or 180 (blue) grit.
Starting at $10.00
S-T213 Nut File - Edge-Cut, for guitars
Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4.5” cutting edge
  • Double sided (both sides are the same gauge)
  • 10 gauges available
  • Sold individually*
  • Made In Japan

*See S-T213-SET for a set of all 10 sizes.
Starting at $11.50
Don't see what you're looking for? Send us your product suggestions!