Tools

Replacement spring for S-TCN255 (Xcelite curved nose pliers).

Butyrate shaft 6-1/8" long with 1/8" wide steel tips. Tip on one end recessed.

• Material: Conductive Nylon Metal
• End: 1/8"
• End 2: 1/8"

Low-profile adhesive standoffs with a 0.180" standoff height that securely attaches your PCB to a flat surface. The post inserts into a 0.125” mounting hole and includes a locking tab that secures the PCB when inserted. It can be used with 1/16” or 1/32” thick PCBs. The 0.6 x 0.6” square base is offset to allow the base to be underneath the board when the mounting hole is close to the PCB edge and the offset base provides a large sticking surface while permitting the PCB to be mounted in tight spaces or close to walls. This can be useful when working with small enclosures. High-quality 3M™ brand double-sided tape secures the standoff to a flat surface. These standoffs are available in packs of 8, 24, or 100 pieces Features:

• Low profile 0.180" standoff height.
• Offset base allows use when holes are close to the PCB edge.

2 inch flat chip brush great for applying tolex glue or any other purposes. This brush features a 4.75 inch wood handle.

Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.

Prototyping circuit board with a standard long strip pattern where tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads and the board has 0.1" hole spacing for DIP integrated circuits/ headers as well as other parts. Higher quality than traditional stripboard, the holes are drilled, not punched.

Replacement sponge for the Weller WLC 100 soldering station ( S-TWLC100 ) and others. Keep your iron tip clean using this genuine Weller replacement sponge. Cleaning a hot soldering iron on a damp sponge causes the solder to contract at a contrasting rate to the soldering iron, helping to remove any solder stuck to the tip. Always be sure the sponge is merely damp rather than soaked in water.

Prototyping circuit board that has a general purpose pad-per-hole pattern making it great for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be easily soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. An anti-tarnish coating protects the copper for a long shelf-life and provides easy soldering.
For fastening your project to a surface see our adhesive standoffs (S-H190-X)
Features:

• Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
• Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
• 31 x 19 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
• Size 1 = 1.97 x 3.15in (50 x 80mm), 1/16" thick (1.6mm)

Prototyping circuit board (PCB) designed to fit the Hammond 1590B die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590B enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190-X) Features:

• Single-sided high-quality FR4 glass-epoxy circuit board.
• Convenient 2-hole pattern provides an easy way to connect parts.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
• 0.042" holes are drilled on 0.1" (2.54mm) centers. 2 mounting holes.
• PCB Size 2.05 x 4.05 in (52.1 x 102.9 mm)

Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application.

• Helps focus glue stream
• Works with all three CA glue viscosities
• Package of 6

5 foot long desoldering braid. Great for removing solder from printed circuit boards or other electronic equipment.

Small magnetizer / demagnetizer for use with hand tools. Simply pass a tool such as a screwdriver through the square hole to magnetize the tool and pass it through the u-shaped channel to demagnetize the tool. Note: When passing through the square cutout to magnetize a tool, be sure to keep the tool from touching the four walls of the magnetizer to ensure a proper magnetization. When using the demagnetizer, the tool can touch the plastic of the channel.

Handheld suction type solder remover.

Hand-held IC extractor for use on a variety of chip sizes. The metal ends hook beneath the chip. When a pinching force is applied to the bends of the plastic, the metal ends clamp onto the chip and pull upward uniformly to avoid bending pins. This tool can be used on widths of 7mm and up.

The SB400 Solderable PCB BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. The SB400 has the same pattern and spacing as a standard 400 connection point BB400 solderless plug-in breadboard. It has a standard 5-hole strip for each IC pin, just like solderless breadboards plus 4 power rails. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The SB400 has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used. BPS prototyping boards use high-quality FR4 glass epoxy PCBs for long life, with an anti-tarnish protective coating for easy soldering.

Fits any adjustable drill or adjustable screwdriver. One size for: guitars, bass, banjos, mandolins, steel guitars, dobros, jazz boxes, etc.

• Precision molded solid body
• No more manual winding ... string your instrument in minutes!
• Direct drive to the tuning keys
• Plastic, will not scratch tuner buttons.
• The ultimate restringing tool for effortless string replacement

Color pictured is an example. Actual color may vary

Designed to protect the fingerboard when doing work on your frets. These shields are indispensable when doing any sort of fret work. Being only .010” thick they can bend to accommodate and fingerboard radius. Made of 304 spring stainless steel.
Comes with 2 sizes: 3-1/8" x 7/8" x .010" - 1/4 inch protection on either side of the fret, 3-1/8"" x 0.59" x .010"" - 3/8 inch protection on either side of the fret

Allen wrench set of three: 2.5mm, 3mm, 4mm

Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.

ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features

• Standard stripboard pattern, with tracks running the length of the board.
• Single-sided high-quality FR4 glass-epoxy circuit board.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering.

Solderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.

Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green

Stainless steel strip, microscored to an ultrafine file surface. Remove oxide and corrosion on contacts made of platinum, paladium, moybdenum, gold, tungsten, and silver.
Commonly used to remove oxidation from electronic contact surfaces such as switches or connectors, restoring the connection and revitalizing the surface.

High quality, made in USA lead formers. These are great tools for bending component leads to fit various footprints. The radiused ends provide a right angle bend that does not stress the metal lead. These lead formers are made of high impact ABS plastic.