Tools

S-ZVT1000 Valve Tester - Orange, VT-1000
The compact and extremely easy to use VT1000 is a fully automatic valve tester, which performs a wide range of tests quickly and accurately. The benefits of using the VT1000 are clear and wide reaching; users can quickly and simply match and test valves, plus receive a reliable health check as to whether their valves are good, bad or worn.
Orange Amps developed the world's first fully automatic, portable, digital valve tester, the VT1000, to make it easy to test amp valves. Until now testing valves with little or no knowledge of valve theory was difficult, expensive and often unreliable.
$444.11
Save 11%
Originally: $499.00
S-TBM4-X Bias Master™ - TAD, tube tester, with 4 probes
Bias Master™ system BM4 Measures Bias current of the vacuum tubes in your amp. Includes 4 probes and english/german operation manual. The Bias Master™ allows you to monitor the bias current safely and easily. While adjusting the Bias control pot of your amp, the Bias Master™ shows the actual result. This lets you set and evaluate the full reasonable biasing range your amp and tubes offer to find and set your personal perfect choice.
$200.21
Save 11%
Originally: $224.95
S-MRFGEN Generator - Lodestar, RF Signal
Compact solid state RF signal generator designed for the hobbyist, service bench and technical instruction. The generator is most suited for checking and aligning the IF circuit and tuners in AM, FM, and TVs. 100 kHz to 150 MHz in 6 bands and up to 450 MHz on third harmonics.
Features:
  • Wide frequency range- 100 Khz to 150 MHz
  • With 1 KHz oscillator purpose of modulation
  • High Stability
  • Output control- 0dB/-20dB/-40dB and fine adjuster
  • Frequency accuracy + or - 5%
  • RF output- 100mV rms appx. (up to 35MHz unloaded)
  • Output control- High-low switch, fine adjust
  • Audio output 1 KHz min., 2V rms
  • Modulation: Internal: 1 KHz (AM) 30% appx., External: 50 Hz ~ 20 KHz at <1V rms input
$158.42
Save 11%
Originally: $178.00
S-MAFGEN Generator - Lodestar, Audio Frequency
The oscillation frequency range of this audio generator is between voice frequency band and super voice frequency band. Square and sine wave. 10K ohm input impedance, 10 V rms maximum input voltage. 600 ohm output impedance. Equipped with synchronized input terminals, enabling the high power output signas to be accurately controlled by small signals. comes with test lead and ground lead. 5.9" high x 9.8" wide x 5.1"deep.
$157.49
Save 11%
Originally: $176.95
S-T262 Fret Slotting Miter Box - for guiding fret saws
Use this Fret Slotting Miter Box to accurately cut fret slots with a fretting handsaw. The ball-bearing guides make sawing easier and faster; they hold your fret saw perpendicular to the fingerboard and can be adjusted to match the blade precisely. You can quickly slot any board up to 3"" (76.2mm) wide, with adjustable depth of cut for any fret wire. You always have an unobstructed view of your work.
Made of rugged aluminum and 12" (304.8mm) long, this miter box has convenient mounting holes for firm attachment to your workbench, the mounting screws and spanners are included. Instructions also included.
$120.15
Save 11%
Originally: $135.00
S-T265 Fret Leveling File - Diamond, 600 grit, Wooden Grip
600 grit diamond fret leveling file used for leveling frets and beveling fret ends. Comfortable wooden handle.
$106.80
Save 11%
Originally: $120.00
S-T213-SET Nut File - Edge-Cut, for guitar, 10 sizes
Package of 10
Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4-1/2” cutting edge
  • Double sided (both sides are the same gauge)
  • Set of 10 files
  • Made In Japan

Set contains one of each size:
  • 0.010"
  • 0.013"
  • 0.016"
  • 0.024"
  • 0.028"
  • 0.032"
  • 0.036"
  • 0.042"
  • 0.046"
  • 0.056"
$106.76
Save 11%
Originally: $119.95
S-T259-A Fret Press - Handheld, 4 cauls
Handheld fret press is a professional fretting tool that gives you finer control over the pressure needed to seat a fret into the slot - you can actually feel it seating! It eliminates complicated clamping setups, so your press-in fret jobs go faster. There's a self-leveling upper caul that adjusts easily to any neck. Used with radius inserts (S-T261) to press frets into guitar fret boards. This method is preferred by many as an alternative to hammering the frets in. Includes 4 interchangeable support cauls.
$97.86
Save 11%
Originally: $109.95
S-T236 Fret File - 600 grit, 3 radiuses, diamond, for Crowns
600 grit diamond-plated file. 3 different, (small, medium, large) radiuses in one file. 130mm file length, 230mm total.
$93.41
Save 11%
Originally: $104.95
S-TWSA350 Bench top smoke absorber - Weller
Keep those fumes out of your face while soldering with this benchtop smoke absorber.
  • Removes flux fumes from soldering workbench
  • Great for workspaces using more active fluxes used with lead-free solder
  • Fumes are absorbed by the replaceable carbon-activated filter
  • Includes one replacement filter (S-TWSA350F)
  • Stand allows the smoke absorber to be adjusted to varying angles
  • Fan is quiet and will not add significant noise to the workspace
  • ESD safe
  • Air Flow Volume: 1370 l/min
  • Wattage: 20 watts
$88.96
Save 11%
Originally: $99.95
S-T239 Fret Saw Guide - for Ensuring Straight Cuts
Three neodymium magnets on each end to ensure a straight cut at a right angle. The saw guide can adjust 0mm to 4.7mm slot depth by sliding the frame. The slide frame side has scale marks representing 1mm of depth. For use with S-T254.
$72.94
Save 11%
Originally: $81.95
S-T9000-LFX Solder - Kester 48, .031", Flux 66, Lead-free 1 lb Spool
Lead free solder, Sn96.5Ag3.0Cu0.5, 031" diameter, rosin flux, core 66. Kester SAC305 48 Activated Rosin Flux for cored solder wire was developed for lead-free applications to enable soldering of most common metals.
Starting at $71.20
Save 11%
Originally: $80.00
S-T1095 Heat gun - Weller, Ungar 1095
UNGAR brand Electric Industrial heat gun with dual temperature. Can be used for applying heat shrinking products, curing epoxy, softening adhesives, drying, molding plastics, heating liquids, etc.
  • Dual temperature settings
  • 3-way switch: Hi-Off-Low
  • 3-wire grounded power cord, 6 feet
  • Wattage: 1000W
  • Temperature Ranges: 1200F - 740F
$67.60
Save 11%
Originally: $75.95
S-TBMA2-X Probes - TAD, for Bias Master™, set of 2
Package of 2
Bias Master™ set of adapter probes for testing other types of tubes. For use with the S-TBM4-X Bias Master™ system.
Starting at $63.63
Save 11%
Originally: $71.50
S-T233-X Drill Bit - two step, for installing vintage tuners
Two-step drill bit for drilling two-step holes. HSS material. Can be used to install vintage type tuners.
$62.26
Save 11%
Originally: $69.95
S-T257 Fret Bender - for creating radius in or flattening Fret Wire
Multi-functional Fret Bender - bend or staighten either bulk fretwire or pre-cut short piece fret wire precisely and quickly! For bending fret wire, crank a length of fretwire through the fret bender, and it comes out curved and ready to install in a radiused fretboard. Get a perfect bend on enough wire for a whole guitar in just seconds. Precisely radiused fretwire makes your fretwork fast, accurate, and professional.
Can be mounted to a workbench by using the two 5/16” bolt holes.
$62.26
Save 11%
Originally: $69.95
S-T224-SET Wrench Set - Boxed Set, assorted sizes
Package of 78
Includes 12 pieces each of 1.27mm, 1.5mm, 2.0mm, 2.5mm, 6 pieces each of 3.0mm, 4.0mm, 5.0mm, 7.0mm, 8.0mm
$60.48
Save 11%
Originally: $67.95
S-T703X Punch - Greenlee, Chassis, for punching round holes
Round hole punches for use in mild steel up to 16 gauge. Make professional chassis punches on your projects. Absolutely no returns unless punch is defective!
Starting at $59.59
S-T211-X Fret File - Diamond, offset, for dressing and shaping frets
Diamond fret file with offset shape for more comfortable fret dressing and improved clearance over the guitar body at high frets. Both full length concave filing grooves (for medium and wide fretwire) uniformly coated with micro industrial diamond particle.
Starting at $59.59
Save 11%
Originally: $66.95
S-T253 Nut Slotting Gauge - Digital
Digital Nut Slotting Gauge. Accurately measure the guitar string height over the first fret with the digital version of this handy luthier’s tool. Display measurements in inches or mm with an accuracy of 0.0005” (0.01 mm). Includes one 1.5V alkaline button cell battery and miniature Philips head screwdriver.
$59.59
Save 11%
Originally: $66.95
S-TWP35 Soldering iron - Weller, WP35, controlled output
  • Input Voltage: 120
  • Power Consumption: 35 watts
  • Tip Temperature: 850ºF
  • Heating Element Type: Nichrome wound, fiberglass and ceramic insulated
  • Lightweight handle with cushion grip for ease of use and comfort
  • Comes with 1/8" screwdriver tip
  • Stand (S-TPH60) sold separately
  • Three wire grounded power cord for your safety
  • UL listed
Stand sold separately (S-TPH60)
$56.03
Save 11%
Originally: $62.95
S-T264 File - Diamond, for Frets, Straight
Double sided diamond fret file. Easily the best choice for fret crowning, diamond files cut in two directions (push and pull) rather than one with no chatter giving you a smoother fret after the crowning process File cutting surface is impregnated with diamonds to give you a smooth cut with long lasting durability.
  • Made of solid steel with diamond cutting surface.
  • Soft rubber coating on the handle
  • 5-3/4” cutting surface
  • Double sided to cover different fret sizes
$56.03
Save 11%
Originally: $62.95
S-TGTBAS1 Bass Player Tech Kit - CruzTOOLS, GrooveTech
Not wanting to leave bass players out, we developed an alternate kit optimized for low-enders. The hex key set is matched to virtually all bass makes, and the string winder has been removed to save a couple of bucks. Like its guitar brethren, the GrooveTech Bass Kit has top-shelf tools that are lifetime guaranteed, and stored in a pouch that will fit into most gig bags. An Easy Setup Guide will make you comfortable with truss rod, action, pickup, and intonation adjustment.
$53.36
Save 11%
Originally: $59.95
S-TGTGTR1 Tech Kit - CruzTOOLS GrooveTech, for Guitar Player
Guitar players may know a little about truss rods and action, but few actually attempt adjustment. That's a shame, because a good setup will improve your performance. The GrooveTech provides everything you need to work on your guitar, plus an Easy Setup Guide that takes the mystery out of the process. Eleven hex keys are color-coded gold for metric and black for inch sizes, and long pattern for easy access. All truss rod sizes are ball end. Also included is a thickness gauge, ruler, capo, cutters, string winder, and 6-in-1 screwdriver.
$53.36
Save 11%
Originally: $59.95
Don't see what you're looking for? Send us your product suggestions!