Tools

S-T-MAGNETIZER Tool - Magnetizer / Demagnetizer
Small magnetizer / demagnetizer for use with hand tools. Simply pass a tool such as a screwdriver through the square hole to magnetize the tool and pass it through the u-shaped channel to demagnetize the tool. Note: When passing through the square cutout to magnetize a tool, be sure to keep the tool from touching the four walls of the magnetizer to ensure a proper magnetization. When using the demagnetizer, the tool can touch the plastic of the channel.
$3.95
S-TVBV Vise - Vacuum base, 40 mm, for securing small components
Mini vise. Great for securing small, light-weight components like potentiometers, tube sockets and switches while soldering or de-soldering. Clamp opens to 40 mm max.
$6.95
S-TMT1 Tip - Weller, Replacement for SP23 and SP23D
Package of 2
MT1 - 0.031" / 0.8 mm Conical Tip For Weller SP23 / SP25 Series Irons. Package of 2
  • Consumer tip series from Weller
  • MT series tips are plated with Electroless Nickel for ease of wetting during soldering
  • 10/24" Thread in tips for SP23 / SP25 series soldering irons
$8.65
S-T266 Fret Setter - 10 cm long, for reseating without unstringing
The contact surface of this solid brass tool fits over the crown of a fret and reseats loose fret ends without unstringing the instrument. Place the end of the tool on the crown of the fret and tap with a hammer. Also works well for pressing loose fret ends down while supergluing.
$12.95
P-PC-ST3U StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$8.35
S-T227 Radius Gauges - 2 Gauges for 8 Radiuses
Package of 2
Solid, high quality stainless steel radius gauges. Use during fingerboard/fret shaping to accurately measure your progress and eliminate mistakes. Can also be used when shaping a nut/saddle or when setting string radius at the bridge. Great for working on compound radius necks. This is an essential tool for a luthier/tech’s bench.
  • Gauge 1 has 7.25", 9.5", 10", and 12" radiuses
  • Gauge 2 has 14", 15", 16", and 20" radiuses
  • Set of 2
$14.00
P-PC-SB404 Breadboard - Solderable PCB, 3.75” x 1.85”, Mounting Holes
Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
$4.50
S-T223 Fret Cutter - 190mm, for Trimming Fret Wire
Fret Cutters. Use to trim the ends of new fret wire close to the fingerboard without leaving marks. Made in Japan. Dimensions:
  • 190 mm total length
  • 27 mm jaw width
$37.95
S-TET-SCREWDRIVER-L Soldering Iron Tip - Weller, hollow core, long screwdriver type, ET Series
Genuine Weller long screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The long screwdriver style is great in situations where additional length is required or for narrow places. These tips are an excellent choice for use with the S-TWE1010 soldering station.
$5.45
S-TGTSC1 String Cutters - CruzTOOLS GrooveTech, for guitar and bass
CruzTOOLS developed the GrooveTech String Cutters specifically for Guitar and Bass strings. Guitar and bass strings are made of hardened stainless steel or nickel with thicknesses as high as 3mm. Ordinary diagonal cutters are designed for soft copper, and thus fail miserably when used on strings. GrooveTech String Cutters were developed specifically for this application, using a proprietary heat-treatment process. Despite its compact five-inch length, even “B” bass strings cut easily and your days of dented blades will be a thing of the past. Vinyl grips feel great in your hands.
$11.95
P-PC-ST2 StripBoard - Single Sided, 3.94” x 3.15”, Mounting Holes
ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$4.55
S-F316-BRUSH Brush - Flat Chip, 2”, 1500, applicator
2 inch flat chip brush great for applying tolex glue or any other purposes. This brush features a 4.75 inch wood handle.
$2.25
S-T1714 Staking Tool - For Small Eyelets
Staking tool for small eyelets such as S-HEYE-B. Directions:
  • Drill hole using #42 drill bit
  • Insert eyelet
  • Flip board over onto a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$13.95
P-PC-PR1590B ProtoBoard - Fits 1590B, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590B die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590B enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190-X) Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 2 mounting holes.
  • PCB Size 2.05 x 4.05 in (52.1 x 102.9 mm)
$3.40
S-B300-X Storage Box - for electronic components
This electronic component storage box works great for storing caps, pots, resistors and other electronic components. Made of plastic.
Starting at $6.25
S-T213-SET Nut File - Edge-Cut, for guitar, 10 sizes
Package of 10
Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4-1/2” cutting edge
  • Double sided (both sides are the same gauge)
  • Set of 10 files
  • Made In Japan

Set contains one of each size:
  • 0.010"
  • 0.013"
  • 0.016"
  • 0.024"
  • 0.028"
  • 0.032"
  • 0.036"
  • 0.042"
  • 0.046"
  • 0.056"
$119.95
S-T303 Guitar Setup Mat - Dunlop, System 65
Work on your guitars without the worry of scratching the finish. This thick neoprene mat measures 17 7/8” x 23 ¾”. The tight webbing on the surface ensures no marring and helps keep debris from sticking to the mat.
$15.25
S-T-CHISEL-X Chisel - Flat, Japanese, Steel, Tataki-Nomi
High quality made in Japan flat chisels for luthier work. These chisels have a blade hardness of HRC63 and a total length of 225mm. The hardwood handle features a flat end for hammering,
Starting at $16.95
S-T-IC-PULLER Tool - IC Extractor / Puller
Hand-held IC extractor for use on a variety of chip sizes. The metal ends hook beneath the chip. When a pinching force is applied to the bends of the plastic, the metal ends clamp onto the chip and pull upward uniformly to avoid bending pins. This tool can be used on widths of 7mm and up.
$3.95
S-T248-X Wood Saw Rasp - High Carbon Steel, coarse side & fine side
Wood rasp - one coarse side for heavy work and one fine side for detailed work
Starting at $21.35
S-T253 Nut Slotting Gauge - Digital, luthier tool
Digital Nut Slotting Gauge. Accurately measure the guitar string height over the first fret with the digital version of this handy luthier’s tool. Display measurements in inches or mm with an accuracy of 0.0005” (0.01 mm). Includes one 1.5V alkaline button cell battery and miniature Philips head screwdriver.
$66.95
S-T-SN390 Vise - PCB Holder, Benchtop, Adjustable Width
Benchtop PCB holder with an adjustable width that can fit PCBs up to 200x140mm. This holder has a sturdy base and the 360° rotation allows easy access to both sides of the board when working. The arms are slotted for different thicknesses allowing for secure clamping of 1.2mm, 1.8mm, 2mm, and 3mm PCBs.
$21.95
S-T216 Fret File - for leveling across multiple frets
For filing straight across multiple frets to ensure that they are level.
$17.75
S-T217-X Saddle File - for Acoustic Guitar Saddle Slots
File for use in filing the saddle of acoustic guitars. Available in 2mm or 3mm options.
$12.75
Don't see what you're looking for? Send us your product suggestions!