Tools

Instrument and amp jacks are notorious for coming loose. And with a shallow nut and recessed cavity, access can be challenging. Until now, that is. The GrooveTech Jack and Pot Wrench provides three thin-wall sockets - ½", 7/16", and 12mm - in a compact four-inch tool to handle the most common sizes of jacks and pots on instruments, amps, and other audio gear. Add a dab of threadlocker, and you'll probably never have to deal with that loose jack again. Sockets are pro-grade with a dazzling polished chrome finish.

Stripboard made with a phenolic substrate. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This stripboard features a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 40 x 20 holes (20 strips). Each strip is surface treated making soldering easier than most protoboards and also ensures a long shelf life. Features: High-quality 1.6mm phenolic circuit board Corrosion resistant, surface treated copper strips 40 x 20 holes (20 strips) 6.14” x 3.15” Looking for projects? See our Wide Stripboard projects in our Pedal Layouts & Build Guides section for ideas.

Bourns trimmer adjustment tool. This tool is compatible with both the R-VT96Y-X multiturn trimmers and the R-VT62P-X single turn trimmers. The recessed end is especially helpful when used with the 3296Y trimmers to avoid slipping off of the screw adjuster. Features

• Meets UL 94V-0
• Pocket clip
• For use on most trimmer shafts/rotors
• Recessed end for use with extended shafts
• RoHS compliant

Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.

• 4.5” cutting edge
• Double sided (both sides are the same gauge)
• 10 gauges available
• Sold individually*
• Made In Japan

*See S-T213-SET for a set of all 10 sizes.

Bias Master™ set of adapter probes for testing other types of tubes. For use with the S-TBM4-X Bias Master™ system.

Gear duster from Befaco. The Befaco Synth Duster is a great tool for getting dust off of faceplates and other hard to reach spots on your equipment. The super soft bristles can gently clean around pots, jacks, and other hardware.

Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.

• ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
• Precision ground copper tips are plated with iron, nickel and chromium
• ST7 - .031" / 0.79 mm diameter Conical tip
• Tinned with Lead Free alloy

Prototyping circuit board that has a general purpose pad-per-hole pattern making it great for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be easily soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. An anti-tarnish coating protects the copper for a long shelf-life and provides easy soldering.
For fastening your project to a surface see our adhesive standoffs (S-H190)
Features:

• Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
• Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
• 31 x 19 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
• Size 1 = 1.97 x 3.15in (50 x 80mm), 1/16" thick (1.6mm)

Double edge nut files featuring popular guitar gauges specially designed for slotting nuts. Each set of files is specifically designed for guitars of a particular type. This set of three files will cover the work of six and cuts a smooth round bottom slot. Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.

• 4” cutting edge
• Set of 3 files
• Made In Japan

Solid steel crowning files with dual cutting edges for precision fret crowning. These should be in any luthier’s tool kit!

• Made of solid steel
• Soft rubber coating on the handle
• Double sided (both sides are the same size)
• 4-3/16” cutting surface
• Available in three sizes to cover most fret sizes (small,medium,large)

Spring loaded center punch with an adjustable force for aligning pilot holes when drilling into materials. The large handle makes the push-to-strike action simple and accurate. Rotating the red handle adjusts the force amount.

Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.

• 4-1/2” cutting edge
• Double sided (both sides are the same gauge)
• Set of 10 files
• Made In Japan

Set contains one of each size:

• 0.010"
• 0.013"
• 0.016"
• 0.024"
• 0.028"
• 0.032"
• 0.036"
• 0.042"
• 0.046"
• 0.056"

Fret Cutters. Use to trim the ends of new fret wire close to the fingerboard without leaving marks. Made in Japan. Dimensions:

• 190 mm total length
• 27 mm jaw width

Solderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.

Genuine Weller long screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The long screwdriver style is great in situations where additional length is required or for narrow places. These tips are an excellent choice for use with the S-TWE1010 soldering station.

This precise set of 20 feeler gauges in the luthier's workshop can perform a wide variety of functions to measuring with string action to measuring the correct nut slot depths, fret slot width, string to fret clearances, and other hardware installation work, these ground steel feeler gauges are marked in both metric and imperial measurements for easy use.

This electronic component storage box works great for storing caps, pots, resistors and other electronic components. Made of plastic.

Handheld suction type solder remover.

Genuine Weller conical style (round) tips for use with all ET Series compatible soldering irons. The concal style is great for general use and precision soldering on small contacts. These tips are an excellent choice for use with the S-TWE1010 soldering station.

• Sensor hole in the base of tip is fitted with a stainless steel liner
• Prevents the tip from seizing to the sensor

Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP

• PT Series Screwdriver Tip for TC201 Series Iron
• PTA7 - 1.6mm / 0.063" diameter screwdriver tip
• Solid copper, plated with iron all over
• Designed to provide maximum heat transfer from the heater to the tip
• Tinned with lead-free solder
• Use only genuine Weller tips

ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features

• Standard stripboard pattern, with tracks running the length of the board.
• Single-sided high-quality FR4 glass-epoxy circuit board.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering.

Replacement colored cap that fits over the S-F312 top. These are sold individually and the color is randomly selected

Our low profile aluminum understring radius gauges have a precision radiused top and bottom for accurate measurement. The slim shape allows you to take measurements of several radii without removing the strings on your guitar.

• Obtain accurate measurements of your instrument's fretboard radius using the bottom radius of the gauge. The bottom radius can also be used to set pickup polepiece height to the string radius.
• Use the top radius of this gauge to determine the proper height adjustment for the bridge saddles.
• The following gauges are included in this set: 7.25" 9.5" 10" 12" 14" 15" 16" 17" 20"

Contains 6 different tools for all standard adjustments. Tools are Delrin with the exception of the potentiometer adjustment tool which is Nylon.
Tools are:

• 8282 Zenith type Hex/Screwdriver
• 8606 5" Hex wrench
• 9091 Hex iron core tool
• 9300 5" Double sided hex tool
• 9304 Hex screwdriver combination
• 8608 Potentiometer Adjustment Tool