# Tools

#### Bob Smith Industries

TAD is a German company established in 1993 which selects and matches electronic tubes and manufactures musical instrument accessories.
Bias Master™ - TAD, tube tester, with 4 probes
Bias Master™ system BM4 Measures Bias current of the vacuum tubes in your amp. Includes 4 probes and english/german operation manual. The Bias Master™ allows you to monitor the bias current safely and easily. While adjusting the Bias control pot of your amp, the Bias Master™ shows the actual result. This lets you set and evaluate the full reasonable biasing range your amp and tubes offer to find and set your personal perfect choice.
$224.95 Adhesive - Bob Smith Industries, Insta-Cure Super Thin Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended. • Water-thin consistency • 1-3 second cure time • For tight fitting applications • Available in 1oz. and 2oz. sizes WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children! Starting at$5.50
Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $5.50 Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506) Starting at$5.50
Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray
Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
• Convenient pump spray (2oz.
Starting at $5.95 Probes - TAD, for Bias Master™, set of 2 Package of 2 Bias Master™ set of adapter probes for testing other types of tubes. For use with the S-TBM4-X Bias Master™ system. Starting at$71.50
Adhesive - Bob Smith Industries, Extender Tip for Glue
Package of 6
Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application.
• Helps focus glue stream
• Works with all three CA glue viscosities
• Package of 6
Starting at \$5.95
Don't see what you're looking for? Send us your product suggestions!