# Tools

Tolex Glue - Brush-on adhesive for applying tolex
Brush-on adhesive ideal for applying tolex. Cleans up with soap and water. No nasty solvents required. Does not stretch or shrink the vinyl. Comes in quarts or gallons. Specifications: Tolex Glue is a non-flammable, Neoprene based, water borne adhesive formulated to bond tolex and vinyl to wood and wood based substrates. Min. use temp: 45°F Freezes at 32°F and lower Shelf Life: 6 Months Directions: Surfaces to be bonded must be clean. Apply a very thin coat to both surfaces. Very porous surfaces may require more than one coat. Second coat should not be applied until first has dried. Allow to 'flash off' for 20-30 minutes. Cloudy areas indicate incomplete drying. This time can be shortened with forced air and/or heat. Position pieces carefully prior to bringing surfaces together as bond is made instantly.
Starting at $32.95 Adhesive - Bob Smith Industries, Insta-Cure Super Thin Bob Smith Industries™ Insta-Cure™ Super Thin Cyanoacrylate. A must have for luthiers! Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds (1-3 sec.). Surfaces to be bonded must be tight fitting (no visible gaps) and should be held together or clamped while you apply the CA around the edges of the seam. For glue applications with small gaps or looser fitting joints the higher viscosity Insta-Cure+™ is recommended. • Water-thin consistency • 1-3 second cure time • For tight fitting applications • Available in 1oz. and 2oz. sizes WARNING: These products are eye and respiratory irritants. Product can bond skin instantly. Keep away from children! Starting at$6.45
Adhesive - Bob Smith Industries, Insta-Cure Gap Filling
Bob Smith Industries™ Insta-Cure+™ Medium Gap Filling Cyanoacrylate. A must have for luthiers! Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps or the parts to be glued don’t fit perfectly. Medium viscosity super glue is the most common glue used in many luthiery applications due to it’s cure time and viscosity. Recommended for binding repair and small poly finish touch ups. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. To speed up curing time use the Insta-Set accelerator!
Starting at $6.45 Adhesive - Bob Smith Industries, Extender Tip for Glue Package of 6 Bob Smith Industries ™ Extender Tip for CA glues. This extender tip can be used with all viscosities (Thin,Medium,Extra Thick) of cyanoacrylate that we offer from Bob Smith Industries™ and is compatible with both available sizes (1oz and 2oz) Extender tips can help you reach difficult spaces and control the flow of glue for more precise application. • Helps focus glue stream • Works with all three CA glue viscosities • Package of 6$3.50
Adhesive - Bob Smith Industries, Maxi-Cure Extra Thick
Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)
Starting at $6.45 Adhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam. • Convenient pump spray (2oz. Starting at$6.45
Threadlocker - Bob Smith Industries, IC-LOC Green
IC-LOC™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-LOC™ Green wicks down into the threads of fasteners using capillary action and has good performance even with oil coated fasteners. Uses
• Bolts
• Screws
• Nuts

Directions: Shake well. Unscrew cap and cut off tip. Apply IC-LOC™ Green to clean preassembled fasteners. Product sets in 10 minutes, with full cure within 24 hours. IC-LOC™ Green prevents the loosening of threaded fasteners from shock and vibration by wicking into threads. Cured temperature range is -60° to +300°F (-51° to +149°C). Locked fasteners are only removable by localized heating and hand tools. Remove residue with a damp cloth. Similar to Loctite Green.
$6.45 Brush - Flat Chip, 2”, 1500, applicator 2 inch flat chip brush great for applying tolex glue or any other purposes. This brush features a 4.75 inch wood handle.$2.95
Adhesive Softener - Bob Smith Industries, Un-Cure
Un-Cure™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of Un-Cure™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastic parts with a razor saw is usually the best option. Works Well On:
• Cyanoacrylates
• Super Glues

Directions: Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water.
$4.69 Adhesive Remover - Bob Smith Industries, Insta-Clean Insta-Clean™ is ideal for removing price stickers and their adhesive residue. Insta-Clean™ will also remove scuff marks that regular household cleaners won't touch. Works on all surfaces, including: glass, cardboard, plastic, fiberglass and everything else. Uses • Stickers • Sticker Residue • Residue on Glass • Residue on Fiberglass Directions: Spray directly onto the sticker to be removed. Let stand for 1 to 5 minutes and then peel off sticker and wipe clean.$4.69
Adhesive Remover - Goo Gone, Original, 8 fl. oz.
Remove sticky, greasy messes with Goo Gone Original and return your surfaces to their original condition. Works on adhesive, crayon, gum, glue.
• Surface safe - formula will not harm your surfaces
• Removes tape - excellent for removing tape from your surfaces
• Perfect for cleaning - great for cleaning clothing, dinnerware and tables
• Removes stickers- great for removing stickers from gifts or even cars
• Use on - adhesive, gum, crayon, glue
$9.95 Adhesive - Bob Smith Industries, Insta-Flex+ Insta-Flex+™ clear rubber toughened has similar qualities to Bob Smith Industries black IC-2000™ but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000™ that gives the CA its black color also contributes to its unsurpassed strength. Since Insta-Flex+™ has this carbon removed, its strength is a little less than IC-2000™ but still superior to standard CA's. When esthetics are important and a flexible bond is required, Insta-Flex+™ is your best choice. It forms superior bonds to soft urethane and vinyl plastics. Both Insta-Flex+™ and Insta-Flex+™ work well when bonding R/C car tires.$10.30
Adhesive - Bob Smith Industries, Super-Gold+
Super-Gold+™ is foam-safe, odorless super glue. Super glues can produce fumes that can be irritating to the eyes and nose. While not toxic, some people can become sensitized to these fumes. Super-Gold+™ is BSI’s odorless form of Cyanoacrylate that gives the same high performance characteristics as BSI’s Insta-Cure+ without the irritating fumes. Super-Gold+ will not fog clear plastic and glass, which can occur with the use of standard Cyanoacrylates. It can also be used on all foams.
Starting at $16.95 Adhesive - Bob Smith Industries, IC-GEL IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as Max-Cure™. IC-GEL™, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL™ can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL™ that you want. IC-GEL™ is an excellent putty for plastic models. It will fill any void and can be formed to many shapes.$12.25
Adhesive - Bob Smith Industries, Plastic-Cure
Plastic-Cure™ is a gap-filling formulation of CA that works best on plastics. It is packaged in a bottle with a brush built into its top, which in many cases is an easier way to apply the CA. As long as brush is put back into the bottle after use, the bristles of the brush will not harden. Care must be taken, however, not to introduce foreign material into the bottle. The brush should not be used, for example, to apply CA to wood that has been freshly sanded. Plastic-Cure will also bond wood, but its brush applicator at times will not be the best way to apply it. Plastic-Cure is superior for the application of false nails and wraps on fingernails, where its brush is the preferred method of application. Uses
• Plastics
• Wood
• Foam
• False nails and wraps on fingernails

Directions: Carefully unscrew the cap.
$8.45 Adhesive - Krylon, 9090, High Strength Spray Adhesive, 11 oz Krylon 9090 high strength spray adhesive. This fast-acting adhesive has a variable volume controlled web spray pattern that offers high contact strength. • Superior, permanent bond • High contact strength • Bonds heavy-duty materials like wood, metal, plastic, glass, laminate and more • Dries in 30 minutes For use on: Wood, Metal, Plastic, Glass, Paper, Papier-mâché, Plaster, Ceramic Application conditions: Best results when temperatures are 55° F to 75°F and humidity is below 60%. Applying outside this range may impact finish Indoor/outdoor: Interior/Exterior$16.95
Don't see what you're looking for? Send us your product suggestions!