Terminal Boards & Strips

Replacement board for Marshall JCM 2000 DSL 100 amplifiers which frequently have issues with original boards. This replacement can bring your amp back to life!
$209.95

Marshall PC Board for TSL 100 / 122. Rev 20.
$209.95

Genuine Fender® Mid Boost upgrade kit for Strats with active electronics. This circuit is used in the signature Eric Clapton and Buddy Guy strats and is commonly referred to as the Clapton Boost. The Mid Boost knob adjusts gain from 0 dB (no boost) to 25 dB (maximum boosted mids). This boost sounds great clean and adds powerful control to distortion.
$59.95

Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.
$29.43

Dual socket. 2 rows/12 lugs per row, 4 mounting holes. Board dimensions 5 ¼" x 3". Terminals are not pre-wired.
$27.50

Package of 2
Turret board with pre installed turrets designed to be used to build a 5F6A layout or variants. Includes the required 2 pieces - 2mm board
- 5F6A Layout
- Includes 2 pieces
$19.80

Single socket, 2 rows/6 lugs per row, 4 mounting holes. Board dimensions 3" x 3". Terminals are not pre-wired.
$18.95

258 x 76 mm, loaded with 52 turrets, 3 mm board thickness. This is designed for a for a JTM45 board. Our turrets, part number S-HTUR-BX will fit on this board.
$16.46

230 x 70 mm, loaded with 33 turrets,2 mm board thickness. This is designed for a 5E3 board.
$15.36

Turret staking tool for use with our turrets (S-HTUR-SG-2X, S-HTUR-SG-3X, S-HTUR-PR-3S).
For anvil see S-T1717
For smaller staking tool, see S-T1714
Directions:
For anvil see S-T1717
For smaller staking tool, see S-T1714
Directions:
- Drill 1/8" hole
- Insert eyelet
- Flip board over on to a hard service
- Center staking tool over the eyelet
- Strike staking tool with hammer to clamp eyelet to board
$14.39

Turret anvil for use with our turrets (S-HTUR-SG-2X, S-HTUR-SG-3X, S-HTUR-PR-3S).
For staking tool see S-T1715
Directions:
For staking tool see S-T1715
Directions:
- Drill 1/8" hole
- Insert eyelet
- Flip board over on to a hard service
- Center staking tool over the eyelet
- Strike staking tool with hammer to clamp eyelet to board
$14.39

Staking tool for small eyelets such as S-HEYE-B. Directions:
- Drill hole using #42 drill bit
- Insert eyelet
- Flip board over onto a hard service
- Center staking tool over the eyelet
- Strike staking tool with hammer to clamp eyelet to board
$14.39

300mm x 60mm turret board conveniently pre-loaded with 2 rows of 30 turrets. Save yourself some time loading the board and move on to building your project!
- Accepts 2mm turrets.
$13.40

Staking tool set that includes both the anvil and swage/punch. The set works with standard turret and eyelet sizes commonly used in amplifiers. The anvil also can be used with Y style turrets.
$12.55

Package of 5
Mini size terminal strips, 1/16" thick phenolic, tin plated brass solder lugs and brackets on 1/4" centers.
$11.95

300mm x 56mm tagboard with two rows of 28 tags. Each connector features two lugs, one facing inward and one facing outward. This can be helpful when connecting components using the inner lugs which leaves the outside lugs open for wiring. A center row of holes can be used for running wires beneath the board as well as for standoffs.
$10.00

Package of 5
Mini size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets on 1/4" centers.
$9.95

Oversized blank G-10 epoxy boards perfect for custom turret or eyelet boards. The large size can be cut down to make multiple boards. With no predilled holes, builders can make clean custom layouts for their projects.
Starting at $9.95

2 rows/12 lugs per row, 2 mounting holes, 5 ¼" x 1 ¼" board dimensions.
$9.95

200mm x 45mm turret board with two rows of of 20 turrets. These turrets are seamless contact pin style turrets. Each turret features an additional solderpad for adding additional components or wiring. This board has four mounting holes.
$9.87

1 row/12 lugs per row. 2 mounting holes. Board dimensions 5 ¼" x ½".
$7.95

2 rows/6 lugs per row, 2 mounting holes. Board dimensions 3" x 1 ¼".
$7.50

Shatterbox style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Shatterbox pedal. The board is styled after the later version with a printed circuit rather than a stripboard construction. This is the same board that was used in the “split board” version which can be built by cutting the board down the middle to separate the fuzz section from the treble booster section. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws.
$6.95

Zonk Machine style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Zonk Machine pedal. The board is styled after the early version that featured a printed circuit rather than a stripboard construction. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
$6.95