Terminal Boards & Strips

P-H219 Board - Marshall, Replacement for JCM 2000 DSL 100
Replacement board for Marshall JCM 2000 DSL 100
$220.50
Save 10%
Originally: $245.00
On Backorder
S-HEYE-A Eyelets - Brass, .121 x .125 x .200; MT .0095, package of 10
Package of 10
Eyelets, bag of 10 (mounts in 1/8" hole).
$0.72
Save 10%
Originally: $0.80
S-HEYE-B Eyelets - Plated Brass, Small, .089” x .125” x .150”
Package of 10
Tin plated brass eyelets commonly used on vintage style pickups. The small sized eyelets are also great for smaller point-to-point projects such as DIY stomp boxes. The outside diameter of the barrel is 0.089” and the recommended mounting hole is 0.093” using a #42 drill bit.
$0.72
Save 10%
Originally: $0.80
P-HFIBER-A Fiberboard - Vulcanized, 3" x 15", .062" Thick
Vulcanized Fiberboard, used for laying out circuits using eyelets such as S-HEYE-A and our staking tool S-T1715.
  • .062" thick
  • 3" x 15"
$2.21
Save 10%
Originally: $2.45
K-704 Kit - Fender® Stratocaster® Mid Boost Kit
Genuine Fender® Mid Boost upgrade kit for Strats with active electronics. This circuit is used in the signature Eric Clapton and Buddy Guy strats and is commonly referred to as the Clapton Boost. The Mid Boost knob adjusts gain from 0 dB (no boost) to 25 dB (maximum boosted mids). This boost sounds great clean and adds powerful control to distortion.
$47.66
Save 10%
Originally: $52.95
P-ECB-25 PC Board - Dunlop, replacement for Crybaby
Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.
$20.66
Save 10%
Originally: $22.95
P-H217 PCB - Marshall, Valve PCB TSL100 / TSL122, Rev 20
Marshall PC Board for TSL 100 / 122. Rev 20. Marshall Part: M-TL10-60-02-01
$212.63
Save 10%
Originally: $236.25
On Backorder
S-H11X Solder Lug - #6 or #8 Hole, Locking
Package of 10
Locking terminal lugs, #6 or #8 hole, 5/8" length, angled. Package of 10
Starting at $1.35
Save 10%
Originally: $1.50
S-T1715 Staking Tool - for Eyelets and Turrets
Turret staking tool for use with our turrets (S-HTUR-AX, S-HTUR-BX, S-HTUR-P).
For anvil see S-T1717
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$8.96
Save 10%
Originally: $9.95
S-T1714 Staking Tool - For Small Eyelets
Staking tool for small eyelets such as S-HEYE-B. Directions:
  • Drill hole using #42 drill bit
  • Insert eyelet
  • Flip board over onto a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$12.56
Save 10%
Originally: $13.95
P-HTAG-16 Tagboard - 300mm x 16mm, 26 Tags, single row
300mm x 16mm tagboard with a single row of 26 tags. Each connector features two lugs for easy wiring. This board can be used for stand alone projects or can be used to expand the P-HTAG-56. This board features four mounting holes.
$4.73
Save 10%
Originally: $5.25
P-HTAG-56 Tagboard - 300mm x 56mm, 2 x 28 Tags
300mm x 56mm tagboard with two rows of 28 tags. Each connector features two lugs, one facing inward and one facing outward. This can be helpful when connecting components using the inner lugs which leaves the outside lugs open for wiring. A center row of holes can be used for running wires beneath the board as well as for standoffs.
$8.96
Save 10%
Originally: $9.95
P-HTAG-40 Tagboard - 40 Turret Pins, High Quality
200mm x 45mm turret board with two rows of of 20 turrets. These turrets are seamless contact pin style turrets. Each turret features an additional solderpad for adding additional components or wiring. This board has four mounting holes.
$8.84
Save 10%
Originally: $9.82
P-TB8-1-2 Terminal Board - one 8 Pin socket, 2 x 6 lugs
Single socket, 2 rows/6 lugs per row, 4 mounting holes. Board dimensions 3" x 3". Terminals are not pre-wired.
$17.06
Save 10%
Originally: $18.95
P-TB9-1-3 Terminal Board - one 9 Pin socket, 3 x 6 lugs
Single socket. 3 rows/6 lugs per row, 6 mounting holes. Board dimensions 3 ¾" x 3". Terminals are not pre-wired.
$21.83
Save 10%
Originally: $24.25
P-TB9-3-2 Terminal Board - three 9 Pin sockets, 2 x 14 lugs
Three socket. 2 rows/ 14 lugs per row, 6 mounting holes. Board dimensions 6 ¾" x 3". Terminals are not pre-wired. The distance between tube socket centers is 2.18".
$36.23
Save 10%
Originally: $40.25
P-TB8-2-2 Terminal Board - two 8 Pin sockets, 2 x 12 lugs
Dual socket. 2 rows/12 lugs per row, 4 mounting holes. Board dimensions 5 ¼" x 3". Terminals are not pre-wired.
$30.56
Save 10%
Originally: $33.95
P-TB9-2-2 Terminal Board - two 9 Pin sockets, 2 x 12 lugs
Dual socket. 2 rows/12 lugs per row, 4 mounting holes. Board dimensions 5 ¼" x 3". Terminals are not pre-wired.
$24.75
Save 10%
Originally: $27.50
P-TB9-2-3 Terminal Board - two 9 Pin sockets, 3 x 10 lugs
Dual socket. 3 rows/10 lugs per row, 4 mounting holes. Board dimensions 5 ½" x 3 ¾". Terminals are not pre-wired.
$31.46
Save 10%
Originally: $34.95
P-TB9-MK3 Terminal Board - two 9 Pin sockets, for Dynaco Mark III
For Dynaco Mark III. Dual socket, 2 rows/11 lugs per row, 4 mounting holes. Board dimension 4.25" x 3.45". 0.125" thickness.
$23.18
Save 10%
Originally: $25.75
P-TS12-1 Terminal Strip - 1 row, 12 turrets per row
1 row/12 lugs per row. 2 mounting holes. Board dimensions 5 ¼" x ½".
$7.16
Save 10%
Originally: $7.95
P-TS6-1 Terminal Strip - 1 row, 6 turrets per row
1 row/6 lugs per row, 2 mounting holes. Board dimensions 3" x ½".
$4.73
Save 10%
Originally: $5.25
P-0201H Terminal Strip - 2 Lug, 2nd Lug Common, Horizontal
Package of 5
Standard size terminal strip, 1/16" thick bakelite, tin plated steel lugs and brackets on 3/8" centers.
$3.11
Save 10%
Originally: $3.45
P-TS12-2 Terminal Strip - 2 rows, 12 turrets per row
2 rows/12 lugs per row, 2 mounting holes, 5 ¼" x 1 ¼" board dimensions.
$8.96
Save 10%
Originally: $9.95
Don't see what you're looking for? Send us your product suggestions!