Terminal Boards & Strips

Replacement board for Marshall JCM 2000 DSL 100
$245.00

Package of 10
Eyelets, bag of 10 (mounts in 1/8" hole).
$0.80

Package of 10
Tin plated brass eyelets commonly used on vintage style pickups. The small sized eyelets are also great for smaller point-to-point projects such as DIY stomp boxes. The outside diameter of the barrel is 0.089” and the recommended mounting hole is 0.093” using a #42 drill bit.
$0.80

Vulcanized Fiberboard, used for laying out circuits using eyelets such as S-HEYE-A and our staking tool S-T1715.
- .062" thick
- 3" x 15"
$2.45

Genuine Fender® Mid Boost upgrade kit for Strats with active electronics. This circuit is used in the signature Eric Clapton and Buddy Guy strats and is commonly referred to as the Clapton Boost. The Mid Boost knob adjusts gain from 0 dB (no boost) to 25 dB (maximum boosted mids). This boost sounds great clean and adds powerful control to distortion.
$52.95

Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.
$22.95

Marshall PC Board for TSL 100 / 122. Rev 20. Marshall Part: M-TL10-60-02-01
$236.25

Package of 10
Locking terminal lugs, #6 or #8 hole, 5/8" length, angled. Package of 10
Starting at $1.50

Turret staking tool for use with our turrets (S-HTUR-AX, S-HTUR-BX, S-HTUR-P).
For anvil see S-T1717
Directions:
For anvil see S-T1717
Directions:
- Drill 1/8" hole
- Insert eyelet
- Flip board over on to a hard service
- Center staking tool over the eyelet
- Strike staking tool with hammer to clamp eyelet to board
$9.95

Staking tool for small eyelets such as S-HEYE-B. Directions:
- Drill hole using #42 drill bit
- Insert eyelet
- Flip board over onto a hard service
- Center staking tool over the eyelet
- Strike staking tool with hammer to clamp eyelet to board
$13.95

300mm x 16mm tagboard with a single row of 26 tags. Each connector features two lugs for easy wiring. This board can be used for stand alone projects or can be used to expand the P-HTAG-56. This board features four mounting holes.
$5.25

300mm x 56mm tagboard with two rows of 28 tags. Each connector features two lugs, one facing inward and one facing outward. This can be helpful when connecting components using the inner lugs which leaves the outside lugs open for wiring. A center row of holes can be used for running wires beneath the board as well as for standoffs.
$9.95

200mm x 45mm turret board with two rows of of 20 turrets. These turrets are seamless contact pin style turrets. Each turret features an additional solderpad for adding additional components or wiring. This board has four mounting holes.
$9.82

Single socket, 2 rows/6 lugs per row, 4 mounting holes. Board dimensions 3" x 3". Terminals are not pre-wired.
$18.95

Single socket. 3 rows/6 lugs per row, 6 mounting holes. Board dimensions 3 ¾" x 3". Terminals are not pre-wired.
$24.25

Dual socket. 2 rows/12 lugs per row, 4 mounting holes. Board dimensions 5 ¼" x 3". Terminals are not pre-wired.
$33.95

Dual socket. 2 rows/12 lugs per row, 4 mounting holes. Board dimensions 5 ¼" x 3". Terminals are not pre-wired.
$27.50

Dual socket. 3 rows/10 lugs per row, 4 mounting holes. Board dimensions 5 ½" x 3 ¾". Terminals are not pre-wired.
$34.95

For Dynaco Mark III. Dual socket, 2 rows/11 lugs per row, 4 mounting holes. Board dimension 4.25" x 3.45". 0.125" thickness.
$25.75

1 row/12 lugs per row. 2 mounting holes. Board dimensions 5 ¼" x ½".
$7.95

1 row/6 lugs per row, 2 mounting holes. Board dimensions 3" x ½".
$5.25

Package of 5
Standard size terminal strip, 1/16" thick bakelite, tin plated steel lugs and brackets on 3/8" centers.
$3.45

2 rows/12 lugs per row, 2 mounting holes, 5 ¼" x 1 ¼" board dimensions.
$9.95

2 rows/6 lugs per row, 2 mounting holes. Board dimensions 3" x 1 ¼".
$7.50