Synth & Eurorack Parts / DIY

Our Synth & Eurorack Parts / DIY category is a curated list of items that are commonly found in synth/eurorack projects. The items and filters here do not represent our full lineup of parts. If you don't see what you are looking for, check out our main categories or send us a suggestion and we'll look into adding it.
C-CX-500 Capacitor - 500V, Ceramic Disc, ± 10%
Radial ceramic capacitor.
  • Voltage rating: 500VDC
  • Tolerance: ± 10%
Starting at $0.25
W-QP-518MA 3.5mm Jack - Qingpu, Eurorack, Mono, Switched Tip, PC Mount
PCB mounted 3.5mm mono jacks commonly found in DIY Eurorack projects. These are the newest version from Qingpu Electronics featuring a square bushing plate for added durability. Hardware sold separately. See accessory items below.
$0.45
P-H5415X Switch - Carling, Mini Toggle, DPDT, 3 Position, Lugs, Short Bat
Carling mini-toggle switch, DPDT, 3 position, ¼" mounting hole diameter, 0.354" bushing length.
  • 0.354" bushing length
  • 3-Position
  • ¼" mounting hole diameter
  • Double pole/Double throw (DPDT)
  • Solder lugs
Starting at $3.95
P-RBTDR-1H-X Reverb Module - Accutronics Belton, Digi-Log, horizontal mount
A great digital reverb sound that easily replaces a spring reverberation unit. Simple interface requires only input, output, +5V, and ground. Output requires no external capacitors.
Starting at $11.01
Save 15%
Originally: $12.95
P-QPT2399 Integrated Circuit - PT2399, Echo / Delay
PT2399 echo/delay chip used in many DIY and commercial pedals. The PT2399 is in a DIP 16 package. Minimal external components are required for use and delay time is set with resistance.
$1.95
C-CDD002-1000 Capacitor - 0.002uF, 1000V, Ceramic Disc, ± 10%
0.002uF ceramic disc capacitor rated for up to 1kV, ± 10% tolerance.
$0.25
P-PC-ST3U StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$8.35
On Backorder
P-KEY-FELT Felt Strip - 51.5", for Korg & Yamaha Keyboards
For Yamaha DX7, DX7 II, FX20, Korg M1, Trinity and T Series.
$5.65
P-H544 Switch - Carling, Mini Toggle, SPDT, On-On, PC Mount, right angle
Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount Features:
  • SPDT ( Single Pole/ Double Throw) On-On switch
  • 0.275" bushing length
  • 0.270” bat length
  • ¼" chassis hole diameter
  • Right angle, PC Mount terminals

Note: On-On switches may sometimes be referred to as On-None-On.
$2.75
P-L400 LED Bezel - with included 3mm Red LED
Bezel Assembly with 3mm Red LED. Required hole size: 0.25". Washer and hex nut included. LED Specifications: Color Red Lens Diam 3 mm Overall Height 5.4 mm Lens Type Diffused Luminous Intensity Min. 3.6 mCd @If (test) 10 mA Wavelngth (Peak) 568 nm V(FM) Max.(V) Forward Voltage 2.7 V @I(F) (test) 10 mA Min Operating Temp -30° Max Operating Temp 80°
$0.85
S-HS-M3-X Screw - M3, Phillips, Pan Head, Machine
Package of 5
Phillips panhead machine screw, M3 metric, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
See S-HS-M3-6-X for colored 6mm M3 screws.
Starting at $0.75
R-VC-FLATWASHER Washer - CTS, Flat, for Potentiometers
Package of 10
Flat washer for 3/8" bushing. Perfect fit for CTS potentiometers. Package of 10.
$1.25
W-QP-NUT-H Nut - Hex, for mounting Qingpu 3.5mm jacks
Hex nut for W-QP-419GR and W-QP-518MA 3.5mm jacks.
See W-QP-NUT-K for the knurled, slotted version of this nut.
See W-QP-WASHER for compatible washer
$0.09
P-Q-SSIDAB2140 Integrated Circuit - DAB2140, Multi-Mode VCF, Sound Semiconductor
The Sound Semiconductor DAB2140 is a pre-soldered DIP converter for the SSI2140. This board features the SSI2140 and two decoupling caps for the V+ and V- inputs. The pinout is labelled on the board and matches the SSOP pinout. This adapter features a 20 pin DIP base with a .600 in. width. The pins are standard male headers so 2.54mm female headers are recommended for socketing the board. For the SSOP version, please see P-Q-SSI2140. A refresh of a classic design, the FatKeys™ SSI2140 preserves mojo of the beloved SSM2040 and adds temperature compensation of gm cells and the exponential control port. A "Q VCA" is provided to allow easy resonance control as well as various options for Q compensation.
$19.95
R-VAMXA Potentiometer - Alpha, Audio, Knurled Shaft, 16mm
Miniature Alpha pot for guitars. Audio taper.
$1.50
P-QTL082 Op-Amp - TL082, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP
Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.
$0.21
P-K379X Knob - Plastic, Set Screw, Vertical Line, 0.525" Diameter
Colors Available:
Small plastic control knob with set screw and brass insert. This knob features a radial-brushed metal top and a stylish vertical knurl. The style is similar to the Boss middle knobs used on many pedals. Fits ¼” (6.35mm) pot shafts.
$0.85
S-W3024TC-X-50 Wire - Weico, 24AWG Stranded, Top Coat Pre-Tinned, 300V, 50 Feet
Colors Available:
High quality 24AWG wire from Weico featuring a topcoat of solder over the strands. This wire is pre-tinned in the sense that a coating of solder is already applied, bonding the individual strands together so no additional tinning is required. This wire is ready to go as soon as it is cut and stripped making assembly that much easier. Rated at 300V and offered in a variety of colors, this wire is a great option for a variety of different projects.
$7.50
P-MSTACT Switch - Korg, Momentary Tactile Switch, Under Knob P8012S
Korg Tact switch under knob P8012S. SPST momentary, 0.25in. width.
$4.25
On Backorder
P-RBTSE-99FX DSP Module - Accutronics, 99 Effects (Reverb, Chorus, Delay, +)
The BTSE-99FX Effect board provides 99 different digital audio effects to be used in many audio applications that require sound enhancement. Equipped with a superb quality digital effects processing engine which adds that extra punch needed to make sounds truly stand out. Applications:
  • Guitar/ Keyboard/Bass amplifiers and combos
  • Audio mixing consoles / Powered mixing consoles
  • Stand -alone stereo effect units for studio and PA usage
  • Effects pedals
$32.00
P-Q-SSI2130 Integrated Circuit - SSI2130, VCO, Sound Semiconductor
The FatKeys™ SSI2130 Voltage Controlled Oscillator provides beautiful triangle, sawtooth, pulse, and square waveforms with unprecedented temperature stability; and adds an on-chip mixer, low distortion sine wave generator, through-zero FM/PM capability and more in an ultra-compact PCB footprint.
$8.95
S-HSO-M3-X Standoff - M3, Male-Female, Aluminum, 5.5mm Diameter
  • Finish/Plating: Clear Iridite
  • Material: Aluminum
  • OD: 5.5mm
  • Shape: Hex (Metric)
  • Style: M-F Standoff
  • Thread Depth(D): 8mm
  • Thread Length (TL): 8mm
  • Thread: M3
  • Type: Threaded Standoffs
Starting at $0.60
P-ECB-67 Knob - Dunlop, MXR, small knurled, aluminum
Genuine Dunlop replacement small knurled knob for MXR pedals. Push -on style knob designed for use with coarse knurled shafts.
$2.35
W-QP-WASHER Washer - Flat, for use on Qingpu Jacks
Flat washer for W-QP-419GR and W-QP-518MA 3.5mm jacks.
$0.09
Don't see what you're looking for? Send us your product suggestions!