Switches

GCB-95 switch. This is a large double pole double throw (DPDT) effect/bypass switch for MXR and Cry Baby pedals, featuring the Dunlop “D” logo.

ECB233 boost / distortion kick switch. Original Dunlop replacement part. Used in the SW95 Crybaby Slash Wah. Through hole PCB mount.

This is a small double pole double throw (DPDT) effect / bypass switch for MXR pedals. Genuine Dunlop replacement part. Six pin through hole PCB mount.

Dunlop® Electronic Components DPDT latching footswitch with solder lugs for MXR, Cry Baby, and other effects pedals.

The LEHLE SWITCH BTN is a momentary foot switch. It is housed in an M12 threaded enclosure made of stainless steel. Thanks to the gold plated contact material its life span is at least one million switching cycles electrically and mechanically. Hardware included.

The LEHLE MODULE SW is a true bypass switching unit with relay and an active pop suppression function controlled by an intelligent microcontroller circuit, thereby allowing the LEHLE MODULE SW to switch even faster than mechanical switches, noise-free and without wear.

Includes: 3 pole, 4 position rotary switch, ¼" output jack and black chicken head knob. Hammond 1600 series transformers all provide secondary impedances of 4, 8, or 16 ohms but due to the unique wiring of the secondary, the impedance cannot be changed without rewiring... Until now. We now offer a selector switch, pre-wired and complete with ¼" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and ¼" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary.

Includes: 3 pole, 3 position rotary switch, ¼" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with ¼" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and ¼" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G) (See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)

Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side.

Rotary impedance selector, 4/8/16. Body screws onto chassis hole.

Heavy duty bat handle, DPDT. Rating: 20A 125V AC, 10A 277V AC Mounts in 1/2" hole, screw connections. On-On.
Note: On-On switches may sometimes be referred to as On-None-On.

3 position (on-off-on) heavy duty bat handle toggle switch with screw terminals. Made in USA.

• Rating: 20A 125VAC, 10A 250VAC, 3/4" HP 125 - 250VAC
• DPDT
• Mounting Hole: .50in.

Standard size slide switches, cadmium plated solder connections. 0.3A 125V, DPDT. Good for Fender® bright switch. Can be used as a 'bright' switch on Fenders. Screws not included.

.3A 125 VAC. 1 pole, 12 position, solid ¼" shaft.

.3A 125VAC. 2 pole, 6 position, solid ¼" shaft.

3 pole, 4 position (make before break) rotary switch with a ¼" solid shaft.

Rotary Switch, 3 Poles, 3 Positions (12 solder terminals), Make Before Break. 1/4 solid shaft Bushing width: 11/32" Bushing height: 5/16" Includes nut & washer 0.3A 125VAC

Single pole multi-position, general purpose rotary switch. This switch features a nylon actuator in a metal clad construction along with a self-cleaning silver plated contact design. Typically used in applications requiring multi-position controls.

4PDT latching footswitch with solder lugs. Blue with 12 solder lugs. Made in Taiwan.

Quad Pole, Double Throw (4PDT), latching footswitch with 12 solder lugs.

Original Marshall™. Black rocker switch for MG amps. 0.51" x 0.76" Mounting Hole. DPST.

For Marshall™, JCM series and others. 15/16" x 1 1/16" x 1" deep.

Lighted power switch. Used in Marshall JCM series and others. 15/16" x 1-1/16" x 1" deep.

Carling SPDT footswitch used in footswitch boxes and effects pedals (112-P). This style of footswitch can be found in many vintage stomp boxes and channel/effect footswitches. The two identical lugs are the two throws and the lug with a unique shape is the common pole.