Switches

R-VTL5C1-P Optocoupler - Vactec, VTL5C1, Vactrol, New Old Stock
New old stock Vactec VTL5C1 vactrols from Perkin Elmer Optoelectronics. These premium vactrols are a great choice for use in phasers, compressors, tremolos, and synth modules such as low-pass gates. They are also used in switching circuits in amplifiers. Limited quantities are available.
$10.95
P-H498-X Switch - Footswitch, DPDT, Vintage Style
Heavy duty footswitch with vintage style solder lugs. Great replacement for stomp-box effects requiring a DPDT (Double Pole, Double Throw) switch. AC125V/4A AC250V/2A.
$3.95
P-H534 Switch - Carling, Mini Toggle, 3PDT
Carling mini-toggle switch, 3PDT, ideal for stomp boxes, phase switching, coil-tapping, series/parallel pickup switching in guitars.
  • 0.354" bushing length
  • 1/4" mounting hole diameter
  • Three pole/double throw (3PDT)
$3.50
S-H111 Nut - Hex, for Carling switches, ~\frac{15}{32}~"
Hex nut for Carling switches, 15/32". Sold individually.
$0.35
P-H590-X Switch - Footswitch, 3PDT, LED Ring
Colors Available:
3PDT. LED ring requires a 11/16" mounting hole. Foot switch button set screw requires 1.5mm hex key.
Starting at $7.95
P-H1701 Switch - Rotary, Impedance Selector, 3 Position
Rotary impedance selector, 4/8/16. Body screws onto chassis hole.
$12.95
P-H542X Switch - Carling, Mini Toggle, DPDT
Genuine Carling DPDT 3 Position Mini Toggle, Round Bat, Solder Lugs
  • DPDT ( Double Pole/ Double Throw) switch
  • 0.354" bushing length
  • 0.409” bat length
  • ¼" chassis hole diameter
  • Solder terminals
Starting at $3.10
W-SC-W11 Switch - Switchcraft, Slide, DPTT, 3-Position
Genuine Switchcraft® DPTT 3-position slide switch for use on Mustang and Duosonic style guitars. This switch can be wired to operate in either On/Off/On or On/On/On configurations. Upgrade cheap or malfunctioning switches with these high quality replacements.
  • Recommended .75 control cavity depth
  • 1.406” center-to-center mounting hole spacing
  • #4-40 screws recommended for mounting
  • Screws not included
$4.75
S-HM301 Switch - Marshall, Toggle, DPST, On-Off, Chrome Tip
Marshall toggle switch, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. See Marshall nut S-HM300N if necessary. Nut sold separately. Note: On-Off switches may sometimes be referred to as On-None-Off.
$15.95
P-SW64 Switch - 3-Way for Tele
Oak 3 way lever switch for Tele® Standard U.S. size. Fits 1/16" x 1-1/16" slot.1-5/8" center to center screw spacing. 1-3/8" cavity depth. The importance of the “right” feel required by guitarists has resulted in a continually designed and developed lever switch, providing a superior product. For over three decades, these lever switches have been tested and refined to meet the needs and desires of guitar players all over the world. Patented “T” slugs secure solder-lug clips to the stator. Mounting screws included.
$7.95
P-SW63 Switch - 5-Way for Strat
Oak® single wafer 5 way lever switch.Standard U.S. size. Fits 1/16" x 1-1/16" slot. 1-5/8" center to center screw spacing. 1-3/8" cavity depth. The importance of the “right” feel required by guitarists has resulted in a continually designed and developed lever switch, providing a superior product. For over three decades, these lever switches have been tested and refined to meet the needs and desires of guitar players all over the world. Patented “T” slugs secure solder-lug clips to the stator. Mounting screws included.
$7.50
P-H410 Switch - Footswitch, 4PDT, Blue, 12 Pins
4PDT latching footswitch with solder lugs. Blue with 12 solder lugs. Made in Taiwan.
$7.95
P-H395 Switch - Rotary, 3 Poles, 3 Position
Rotary Switch, 3 Poles, 3 Positions (12 solder terminals), Make Before Break. 1/4 solid shaft Bushing width: 11/32" Bushing height: 5/16" Includes nut & washer 0.3A 125VAC
$2.50
S-M560 Insulation - GC Electronics, fibroid, "fish paper"
Vulcanized Cellulose Fiber for all electrical insulation. Gray insulating paper. .010" thick. used in switches, under terminals, in transformers, etc .where mechanical strength is required. Its qualities of toughness, flexibility, and edge-tearing resistance combined with high dielectric strength and ready absorption of insulating varnish have led to its predominant use as an improved motor slot call insulation. Dielectric strength 3000 volts. 10" wide roll contains 240 sq. inches.
$5.25
W-SC-W09 Nut - Switchcraft, Knurl Nut for Switches
Original Switchcraft Copper Alloy Knurled Locknut (Nickel Plated)
Outside Diameter:5/8"
Inside diameter threading:15/32"
Width: 3/32"
$1.50
W-SC-W01 Switch - Switchcraft, Pickup Selector, for Gibson® L-Type
Switchcraft Pickup Selector, Replacement for Gibson L-Type. Similar to Gibson® P-SW01. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG.
$16.95
W-SC-W0213 Switch - Switchcraft, Pickup Selector, for Gibson® Straight
Colors Available:
Switchcraft Pickup Selector, Replacement for Gibson Straight-Type. As found on LP style solid body guitars.
Starting at $14.25
W-SC-W0X Switch Tip - Switchcraft, for Gibson® Pickup Selectors
Colors Available:
Switchcraft Switch Tip for Gibson Pickup Selectors. Multiple color options available. Threading: 8-32 Replacement for Gibson: PRTK-010
Starting at $2.15
S-HM300N Nut - Marshall, for S-HM301 Toggle Switch, Chrome
Chrome slotted nut for part S-HM301 toggle switch.
  • Thread size = 15/32 - 32 thread pitch
$3.50
S-HRVLW Washer - Fender®, Lock Type, for Potentiometers
Package of 12
Lock washer for Fender® pots. Package of 12.
$4.25
R-VOP1020 Switch - Vibrato LDR, for Fender® Amps
Optocoupler. Vibrato LDR for Fender Amps.
Fix the dead LDR style tremolo on your vintage Fender amps as well as others.
  • Non- polarized optical side is indicated by silver dot and slightly longer leads
  • Resistive side is indicated only by slightly shorter leads

This information can also be found within the diagram located in the Specifications, Files, and Documents section on this page.
$8.95
R-VTL5C1 Optocoupler - VTL5C1, Vactrol, for Channel Switching
VTL5C1 vactrols for use in amplifiers, effect pedals, synthesizers and more. The VTL5C1 was commonly used for channel switching circuits in amps made by Crate and others.
$7.95
P-SW50 Switch - Fender®, Pickup Selector, Strat & Tele 3-Way
Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender® offers this high quality, 3 position switch with knob and mounting hardware.
$10.95
P-SW51 Selector Switch - Fender®, Pickups, American Strat 5-Way
Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender® offers this high quality 5-position pickup selector switch. Includes mounting screws, one white and one black switch tip. Fender part number: 099-1367-000
$8.95
Don't see what you're looking for? Send us your product suggestions!