Switches

S-HM100-A Switch - Rotary, Voltage Selector, Modern, for Marshall
  • Ratings:
    • IEC: 6.3 A / 250 VAC; 50 Hz
    • UL: 10 A / 250 VAC; 60 Hz
    • CSA: 8 A / 250 VAC; 60 Hz
  • Mounting: Panel Mount from front side
  • Fastening: Screw-on mounting
  • Terminal: Solder
  • Number of Stages: 3
  • Type: SP3T
  • Lifetime: 300 operating cycles (without load)
  • Degree of Protection: IP 40
  • Allowable Operation Temp.: -40 °C to 85 °C
  • Climatic Category: 25/85/21 acc. to IEC 60068-1
  • Material of Socket: Thermoplastic, black, UL 94V-0
  • Weight: 16.5 g
  • Solderability: 350 °C / 2 sec acc. to IEC 60068-2-20, Test Ta, method 2
  • Resistance to Soldering Heat: 350 °C / 10 sec acc. to IEC 60068-2-20, Test Tb, method 2
  • Insulation Resistance: > 10,000MΩ (500VDC; 1min)
  • Contact Resistance: < 10 mΩ at 20 mV
  • Dielectric Strength:
    • > 2.5kVAC between L-N (1min; 50Hz)
    • > 4kVAC between L/N-PE (1min; 50Hz)
  • Clearance and Creepage Distance:
    • > 5mm
    • > 8mm between L/N-PE
  • Resistance to Vibration: acc. to IEC 60068-2-6, test Fc
$35.45
P-H1700 Switch - Rotary, Impedance Selector, Replacement for Marshall
Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side. SP3T.
$34.95
On Backorder
P-H603 Switch - for Run Circuit in Hammond Organ
Switch for run circuit in Hammond Organ. Electrical Rating: 16 A - 125 V 8 A - 250 V Dimensions: Mounting Diameter: ½" Bushing Length: 0.425" Length: 1.89" Width: 0.82" Depth: 0.69"
$29.95
On Backorder
W-SC-W16 Switch - Switchcraft, Pickup Selector Toggle, SPST, right angle
Switchcraft 3 Position Pickup Selector, Replacement for Gibson L-Type. Similar to Gibson® P-SW01. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG. Features a slightly longer (3/8”) bushing ideal for thicker topped guitars.
  • Tip not included. See W-SC-W0X
  • Black finish
$29.95
W-SC-W15 Switch - Switchcraft, Pickup Selector Toggle, DPDT, Right Angle
Switchcraft 3 Position Pickup Selector, replacement for Gibson L-Type. Similar to Gibson®. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG.
  • Tip not included. See W-SC-W0X (Note: Two threads will show beneath the switch cap.)
  • Nickel Finish
$28.29
W-SC-W14 Switch - Switchcraft, Pickup Selector Toggle, 3-Way, right angle
Switchcraft 3 Position Pickup Selector, replacement for Gibson L-Type. Similar to Gibson®. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG.
Tip not included, see W-SC-W0X

Nickel Finish
$21.95
W-SC-W01 Switch - Switchcraft, Pickup Selector, for Gibson® L-Type
Switchcraft 3 position Pickup Selector, Replacement for Gibson L-Type. Similar to Gibson® PSTS-010. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG. This version of the L-Type switch is used in the common two pickup wiring for a neck position, middle position with neck and bridge, and a bridge position.
$20.95
W-SC-W12 Switch - Switchcraft, Toggle, 3-way, for Les Paul
One of the most rugged and durable switches available for your Gibson Les Paul or similar two pickup guitars.
$20.95
P-H501-DEMONT Footswitch - 3PDT, DeMont, Latching, Smooth-Click
Premium quality latching 3PDT switches from DeMont / Guyatone. These made in Japan switches are designed specifically for audio signals. The Demont 3PDT has ultra-smooth switching action and has a very low actuation force. It uses gold plated solder cup terminals for solid connections with a professional look. Mounting hardware included.
$18.95
P-SW52 Switch - Fender®, Pickup Selector, 5-Way
Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender&reg offers this high quality, 5 position super switch with knob and mounting hardware.
$18.95
W-SC-W0213 Switch - Switchcraft, Pickup Selector, for Gibson® Straight
Colors Available:
Switchcraft 3 position Pickup Selector, Replacement for Gibson Straight-Type. As found on LP style solid body guitars.
Starting at $18.95
P-SW53 Switch - Fender®, Pickup Selector, 4-Way Telecaster Mod
Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender&reg offers this high quality, 4 position switch with knob and mounting hardware. Telecaster players have long debated the merits of having their pickups wired in parallel vs. in series. In the traditional parallel wiring configuration, pickup output is relatively consistent across all three positions. A Telecaster with its pickups wired in series differs in that when both pickups are on at the same time, the combination produces fatter tone and higher output.
$18.95
P-H1701 Switch - Rotary, Impedance Selector, 3 Position
Rotary impedance selector, 4/8/16. Body screws onto chassis hole. SP3T switch.
$16.95
S-HM301 Switch - Marshall, Toggle, DPST, On-Off, Chrome Tip
Marshall toggle switch, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. See Marshall nut S-HM300N if necessary. Nut sold separately. Note: On-Off switches may sometimes be referred to as On-None-Off.
$15.95
S-HM301-A Switch - Toggle, DPST, On-Off, Chrome Tip
Toggle switch for Marshall amps, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. Mounting nuts (1 hex and 1 knurled) included. Main features:
  • Construction : Terminal and contact support are manufactured from a single piece of metal. The contacts are resistance-welded to the terminal for increased mechanical strength.
  • Rating : These switches are suitable for motor loads and power applications up to 15A 250VAC
  • UL, CSA and NF-VDE (EN 61058-1) approved

Note: On-Off switches may sometimes be referred to as On-None-Off.
$14.95
P-ECB-555 Switch - Dunlop, Footswitch, DPDT, Solder Lugs, for MXR
Dunlop® Electronic Components DPDT latching footswitch with solder lugs for MXR, Cry Baby, and other effects pedals.
$14.95
P-H600-A Switch - Rotary, 1 Pole, 3 Position
High quality three position rotary switch commonly used as an impedance selector switch on tube amps. This rugged switch is rated for 6A at 125VAC and 3A at 250VAC. The flatted 6mm shaft can be used with the shaft adapter found in the accessories below to easily fit standard ¼” knobs. Mounting hardware included. SP3T.
$12.95
P-H-ST8206 Footswitch - ST Professional, 4PST, Latching, Solder Lugs
Heavy duty 4PST latching switch made in Italy by ST Professional. The body is made of PBT that is riveted to the bushing plate for a sturdy construction. The actuation force is lighter than similar Carling switches and provides tactile and audible feedback so the switching action is apparent to the user. This version features standard solder lugs. This style of footswitch is similar to the vintage footswitches found in the Schaller Fuzz, some Tonebender models, and others.
$12.95
P-H491 Switch - Rocker, Lighted Power, Used in JCM Series & Others
Lighted DPST On-Off power switch. Used in Marshall JCM series and others. 15/16" x 1-1/16" x 1" deep.
$12.50
P-ECB-035 Switch - Dunlop, Footswitch, GCB-95
GCB-95 latching switch. This is a large double pole double throw (DPDT) effect/bypass switch for MXR and Cry Baby pedals, featuring the Dunlop “D” logo.
$12.43
P-H1600 Switch - Rotary Impedance Selector, for Hammond 1600 Series
Includes: 3 pole, 4 position rotary switch (3P4T), 1/4" output jack and black chicken head knob. Hammond 1600 series transformers all provide secondary impedances of 4, 8, or 16 ohms but due to the unique wiring of the secondary, the impedance cannot be changed without rewiring... Until now. We now offer a selector switch, pre-wired and complete with 1/4" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and 1/4" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary.
$11.95
P-H497 Footswitch - Carling, DPDT, Side Solder Lugs
Good latching stomp-box effects switch (Double Pole, Double Throw), On-On. Solder Lugs. 1A 250V, 3A 125V Note: On-On switches may sometimes be referred to as On-None-On.
$11.95
P-H1600-A Switch - Rotary Impedance Selector, for Hammond 1600A series
Includes: 3 pole, 3 position rotary switch (3P3T), 1/4" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with 1/4" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and 1/4" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
$11.95
P-SW50 Switch - Fender®, Pickup Selector, Strat & Tele 3-Way
Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender® offers this high quality, 3 position switch with knob and mounting hardware.
$11.50
Don't see what you're looking for? Send us your product suggestions!