Switches

- Ratings:
- IEC: 6.3 A / 250 VAC; 50 Hz
- UL: 10 A / 250 VAC; 60 Hz
- CSA: 8 A / 250 VAC; 60 Hz
- Mounting: Panel Mount from front side
- Fastening: Screw-on mounting
- Terminal: Solder
- Number of Stages: 3
- Type: SP3T
- Lifetime: 300 operating cycles (without load)
- Degree of Protection: IP 40
- Allowable Operation Temp.: -40 °C to 85 °C
- Climatic Category: 25/85/21 acc. to IEC 60068-1
- Material of Socket: Thermoplastic, black, UL 94V-0
- Weight: 16.5 g
- Solderability: 350 °C / 2 sec acc. to IEC 60068-2-20, Test Ta, method 2
- Resistance to Soldering Heat: 350 °C / 10 sec acc. to IEC 60068-2-20, Test Tb, method 2
- Insulation Resistance: > 10,000MΩ (500VDC; 1min)
- Contact Resistance: < 10 mΩ at 20 mV
- Dielectric Strength:
- > 2.5kVAC between L-N (1min; 50Hz)
- > 4kVAC between L/N-PE (1min; 50Hz)
- Clearance and Creepage Distance:
- > 5mm
- > 8mm between L/N-PE
- Resistance to Vibration: acc. to IEC 60068-2-6, test Fc
$35.45

Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side. SP3T.
$34.95

Reliable replacement relay for the Leslie 122. The small size makes this high quality relay easy to retrofit in the 122. Its performance exceeds the original relays used in the Leslie 122 with its very low switching noise and high ratings on both the contacts and the coil. Features:
- 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
- Coil EMC suppression
$32.95

Reliable replacement relay for the Leslie 147. The small size makes this high quality relay easy to retrofit in the 147. Its performance exceeds the original relays used in the Leslie 147 with its very low switching noise and high ratings on both the contacts and the coil. Features:
- 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
- Coil EMC suppression
- Cadmium Free contact material
$32.50

Switch for run circuit in Hammond Organ. Electrical Rating: 16 A - 125 V 8 A - 250 V Dimensions: Mounting Diameter: ½" Bushing Length: 0.425" Length: 1.89" Width: 0.82" Depth: 0.69"
$29.95

Switchcraft 3 Position Pickup Selector, Replacement for Gibson L-Type. Similar to Gibson® P-SW01. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG. Features a slightly longer (3/8”) bushing ideal for thicker topped guitars.
- Tip not included. See W-SC-W0X
- Black finish
$29.95

Switchcraft 3 Position Pickup Selector, replacement for Gibson L-Type. Similar to Gibson®. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG.
- Tip not included. See W-SC-W0X (Note: Two threads will show beneath the switch cap.)
- Nickel Finish
$28.29

The LEHLE MODULE SW is a true bypass switching unit with relay and an active pop suppression function controlled by an intelligent microcontroller circuit, thereby allowing the LEHLE MODULE SW to switch even faster than mechanical switches, noise-free and without wear.
Starting at $22.95

Switchcraft 3 Position Pickup Selector, replacement for Gibson L-Type. Similar to Gibson®. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG.
Tip not included, see W-SC-W0X
Nickel Finish
Tip not included, see W-SC-W0X
Nickel Finish
$21.95

One of the most rugged and durable switches available for your Gibson Les Paul or similar two pickup guitars.
$19.95

Switchcraft 3 position Pickup Selector, Replacement for Gibson L-Type. Similar to Gibson® PSTS-010. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG. This version of the L-Type switch is used in the common two pickup wiring for a neck position, middle position with neck and bridge, and a bridge position.
$19.95

Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender® offers this high quality, 4 position switch with knob and mounting hardware. Telecaster players have long debated the merits of having their pickups wired in parallel vs. in series. In the traditional parallel wiring configuration, pickup output is relatively consistent across all three positions. A Telecaster with its pickups wired in series differs in that when both pickups are on at the same time, the combination produces fatter tone and higher output.
$18.95

Colors Available:
Starting at $18.95

Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender® offers this high quality, 5 position super switch with knob and mounting hardware.
$18.95

Rotary impedance selector, 4/8/16. Body screws onto chassis hole. SP3T switch.
$16.95

The LEHLE SWITCH BTN is a momentary foot switch. It is housed in an M12 threaded enclosure made of stainless steel. Thanks to the gold plated contact material its life span is at least one million switching cycles electrically and mechanically. Hardware included.
Starting at $16.55

Marshall toggle switch, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. See Marshall nut S-HM300N if necessary. Nut sold separately. Note: On-Off switches may sometimes be referred to as On-None-Off.
$15.95

Premium quality latching 3PDT switches from DeMont / Guyatone. These made in Japan switches are designed specifically for audio signals. The Demont 3PDT has ultra-smooth switching action and has a very low actuation force. It uses gold plated solder cup terminals for solid connections with a professional look. Mounting hardware included.
$15.25

Toggle switch for Marshall amps, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. Mounting nuts (1 hex and 1 knurled) included. Main features:
Note: On-Off switches may sometimes be referred to as On-None-Off.
- Construction : Terminal and contact support are manufactured from a single piece of metal. The contacts are resistance-welded to the terminal for increased mechanical strength.
- Rating : These switches are suitable for motor loads and power applications up to 15A 250VAC
- UL, CSA and NF-VDE (EN 61058-1) approved
Note: On-Off switches may sometimes be referred to as On-None-Off.
$14.95

Dunlop® Electronic Components DPDT latching footswitch with solder lugs for MXR, Cry Baby, and other effects pedals.
$14.95

Vintage style selector switch male part, replacement for Marshall.
$12.95

High quality three position rotary switch commonly used as an impedance selector switch on tube amps. This rugged switch is rated for 6A at 125VAC and 3A at 250VAC. The flatted 6mm shaft can be used with the shaft adapter found in the accessories below to easily fit standard ¼” knobs. Mounting hardware included. SP3T.
$12.95

Heavy duty 4PST latching switch made in Italy by ST Professional. The body is made of PBT that is riveted to the bushing plate for a sturdy construction. The actuation force is lighter than similar Carling switches and provides tactile and audible feedback so the switching action is apparent to the user. This version features standard solder lugs. This style of footswitch is similar to the vintage footswitches found in the Schaller Fuzz, some Tonebender models, and others.
$12.95

GCB-95 latching switch. This is a large double pole double throw (DPDT) effect/bypass switch for MXR and Cry Baby pedals, featuring the Dunlop “D” logo.
$12.43