Switches

Rubber caps / switch tips for mini toggle switches in a variety of colors. These are made for standard sized toggle bats.

Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount Features:

• SPDT ( Single Pole/ Double Throw) On-On switch
• 0.275" bushing length
• 0.270” bat length
• ¼" chassis hole diameter
• Right angle, PC Mount terminals

Note: On-On switches may sometimes be referred to as On-None-On.

Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side. SP3T.

Genuine Carling hex nut commonly used on full size toggle switches and footswitches. This nickel plated hex nut has a 15/32 threading.

High quality vactrols from Xvive. The Xvive vactrols are clones of the original Excelitas / Perkins-Elmer vactrols used in many effects pedals, synthesizers, compressors and other equipment. These vactrols feature a thick epoxy sealed casing. The VTL5C3 and VTL5C3/2 both have a steep slope, good dynamic range, a very low temperature coefficient of resistance, and a small light history memory.

Carling mini-toggle switch, SPDT, Solder Lug, 3-Position, On/Off/On

.3A 125 VAC. 1 pole, 12 position, solid 1/4" shaft. SP12T rotary switch.

Rotary impedance selector, 4/8/16. Body screws onto chassis hole. SP3T switch.

Genuine Switchcraft® DPTT 3-position slide switch for use on Mustang and Duosonic style guitars. This switch can be wired to operate in either On/Off/On or On/On/On configurations. Upgrade cheap or malfunctioning switches with these high quality replacements.

• Recommended .75 control cavity depth
• 1.406” center-to-center mounting hole spacing
• #4-40 screws recommended for mounting
• Screws not included

Latching DPDT footswitch, PC mount. Made in Taiwan.

Genuine Carling DPDT 3-position mini toggle switch with solder lugs. These switches feature a flattened actuator.

• 0.354" bushing length
• 3-Position
• ¼" chassis hole diameter
• DPDT ( Double Pole/ Double Throw) switch
• Solder Lugs

High-quality solder lug audio taper 16mm pots from Gorva Design. Gorva Design left no boxes unchecked when engineering their potentiometer lineup. Every element was carefully designed to offer builders an exceptional potentiometer with high durability and tight tolerances. Gorva potentiometers are made with stompboxes in mind but offer the same advantages to amplifiers, synthesizers, studio equipment and other electronics.

• Solder lug / panel mount
• Audio taper
• +/- 10% tolerance
• ¼” (6.35mm) solid shaft
• Machine-pressed dust seal
• High quality wiper material
• Low residual resistance

For linear taper solder lug pots see R-VGORVA-BX-SL. For audio taper right-angle PCB mount pots see R-VGORVA-AX-PC. For linear taper right-angle PCB mount pots see R-VGORVA-BX-PC.

Carling, DPST 2 position toggle switch, On-Off with .25" tabs (6A, 125VAC). Note: On-Off switches may sometimes be referred to as On-None-Off.

SPST(single pole,single throw) normally open, Off-(On) momentary foot switch with solder lugs and soft switching. These high quality switches feature a black actuator, bushing and mounting hardware. Depressing the switch shorts the lugs together and when the switch is released it returns to its non connected state with no click.

• SPST momentary switch
• Black finish and hardware
• Soft, silent switching with no click
• Normally open operation
• Solder lugs
• Nuts and washer included
• Note: Off-(On) switches may sometimes be referred to as Off-None-(On).

3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.

Carling mini-toggle switch, 3PDT, ideal for stomp boxes, phase switching, coil-tapping, series/parallel pickup switching in guitars.

• 0.354" bushing length
• 1/4" mounting hole diameter
• On-On Three pole/double throw (3PDT)

Carling, DPDT 2 position toggle with solder lugs (6A, 125V), .50" toggle length (shorter bat). On-On.
Note: On-On switches may sometimes be referred to as On-None-On.

3PDT latching footswitch with PC terminals. Blue with 9 terminals. Made in Taiwan.

Original Fender set of two pickup switch tips for use on most U.S. and Mexico-made Stratocaster® models.

Carling, 2 position DPDT toggle switch with screw terminals. On-On. Note: On-On switches may sometimes be referred to as On-None-On.

Rectangular rocker switch that uses a round mounting hole. This black nylon rocker switch has a small panel footprint and is easy to add to projects due to the round mounting hole. Mounting nut and lock washer included.

• SPST
• On-Off
• 6A, 125VAC / 3A, 250VAC
• 12.2mm Mounting Hole

SPST On-Off toggle switch. Made in Taiwan (M10 x.1.0 threading) .39" bushing diameter.

High quality switch indicator plates from Carling. These are made from nickel plated steel and feature deeply engraved text. These indicator plates fit full sized Carling toggle switches.

Heavy duty SPST Off-(On) momentary switch made in Italy by ST Professional. Rated for 2A at 240V, these switches can be used in a wide range of applications. The body is made of PBT that is riveted to the bushing plate for a sturdy construction. The actuation force is lighter than similar Carling momentary switches and provides tactile and audible feedback so the switching action is apparent to the user. The pins also feature eyelets so hardwiring is an option in addition to the standard PCB mount.