Switches

Carling miniature rocker switch, DPST with .187" tabs (Marshall style). On-Off. 4A 250VAC; 8A 125VAC; 6A 250V. This switch is ideal for applications with back panel size constraints. It fits in a standard rectangular cutout and is designed to provide ease of insertion along with superior panel retention qualities. A high profile rocker and butt-action contacts provide the user with a crisp positive-type feel.

Tele "Top Hat" tip, black.

Carling SPDT 3 position center off toggle. Great Fender ground switch replacement, 3A, 250VAC; 6A, 125VAC.

3PDT latching footswitch with PC terminals. Blue with 9 terminals. Made in Taiwan.

Genuine Fender replacement switch. Push SLFLK Short Stroke. 6 pin PCB mount

Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender&reg offers this high quality, 5 position switch with knob and mounting hardware.

Switchcraft Pickup Selector, replacement for Gibson L-Type. Similar to Gibson®. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG.

• Tip not included, see W-SC-W0X
• Nickel Finish

New old stock Vactec VTL5C1 vactrols from Perkin Elmer Optoelectronics. These premium vactrols are a great choice for use in phasers, compressors, tremolos, and synth modules such as low-pass gates. They are also used in switching circuits in amplifiers. Limited quantities are available.

DPDT momentary footswitch. AC125V/4A AC250V/2A

Original Fender®, Carling SPST standby for Fender tube amps - 3A, 250VAC; 6A, 125VAC.

Quad Pole, Double Throw (4PDT), latching footswitch with 12 solder lugs.

Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender&reg offers this high quality, 4 position switch with knob and mounting hardware. Telecaster players have long debated the merits of having their pickups wired in parallel vs. in series. In the traditional parallel wiring configuration, pickup output is relatively consistent across all three positions. A Telecaster with its pickups wired in series differs in that when both pickups are on at the same time, the combination produces fatter tone and higher output.

• Ratings:
  
  • IEC: 6.3 A / 250 VAC; 50 Hz
  • UL: 10 A / 250 VAC; 60 Hz
  • CSA: 8 A / 250 VAC; 60 Hz
• Mounting: Panel Mount from front side
• Fastening: Screw-on mounting
• Terminal: Solder
• Number of Stages: 3
• Lifetime: 300 operating cycles (without load)
• Degree of Protection: IP 40
• Allowable Operation Temp.: -40 °C to 85 °C
• Climatic Category: 25/85/21 acc.

Original Fender®, Carling SPST power for Fender tube amps - 3A, 250VAC; 6A, 125VAC, ½" mounting hole.

Carling, SPST toggle, momentary. 3A 250V, 6A 125V. Made in Mexico.

Marshall toggle switch, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. See Marshall nut S-HM300N if necessary. Nut sold separately. Note: On-Off switches may sometimes be referred to as On-None-Off.

Vulcanized Cellulose Fiber for all electrical insulation. Gray insulating paper. .010" thick. used in switches, under terminals, in transformers, etc .where mechanical strength is required. Its qualities of toughness, flexibility, and edge-tearing resistance combined with high dielectric strength and ready absorption of insulating varnish have led to its predominant use as an improved motor slot call insulation. Dielectric strength 3000 volts. 10" wide roll contains 240 sq. inches.

4PDT latching footswitch with solder lugs. Blue with 12 solder lugs. Made in Taiwan.

5-way switch for Strats, black tip.

Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount
Features:

• SPDT ( Single Pole/ Double Throw) On-On switch
• 0.275" bushing length
• 0.270” bat length
• ¼" chassis hole diameter
• Right angle, PC Mount terminals

Note: On-On switches may sometimes be referred to as On-None-On.

Carling, DPDT 2 position toggle with solder lugs (3A, 125V), .50" toggle length. On-On. Dimensions:

• Body Length (less solder lugs) = 0.984"
• Body Depth (height) = 0.580"
• Body Width = 0.528"
• Toggle Length =.50"

Note: On-On switches may sometimes be referred to as On-None-On.

Switch for run circuit in Hammond Organ. Electrical Rating: 16 A - 125 V 8 A - 250 V Dimensions: Mounting Diameter: ½" Bushing Length: 0.425" Length: 1.89" Width: 0.82" Depth: 0.69"

Hex nut for Carling switches, 15/32". Sold individually.

Includes: 3 pole, 3 position rotary switch, ¼" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with ¼" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and ¼" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G) (See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)