Switches

Fender® style power and/or standby switch (Single Pole, Single Throw). This switch is a great replacement for older Fender® amps where the shorter toggle length (1/2”) is desired.

Carling, 2 position, On-Off, SPST with solder lugs, 1/2" mounting hole.
Note: On-Off switches may sometimes be referred to as On-None-Off.

Dress nuts for use with mini toggle switches. These plated dress nuts feature a chamfered edge for a professional look and work on any 1/4-40 UNS threaded bushing. Two sides are flatted for use with a tool when fastening.

Carling, SPDT mini toggle, 2 positions, ¼" mounting hole diameter, 0.354" bushing length.

Genuine Carling DPDT 3 Position Mini Toggle, Round Bat, Solder Lugs

• DPDT ( Double Pole/ Double Throw) switch
• 0.354" bushing length
• 0.409” bat length
• ¼" chassis hole diameter
• Solder terminals

Standard size slide switches, cadmium plated solder connections. 0.3A 125V, DPDT, On-On. Good for Fender® bright switch. Can be used as a 'bright' switch on Fenders. Screws not included.

Carling, SPDT mini toggle, 2 positions, ¼" mounting hole diameter, 0.354" bushing length.

Carling mini-toggle switch, DPDT, 2 position, ¼" mounting hole diameter, 0.354" bushing length.

Genuine Switchcraft® DPDT 2-position slide switch for use on Jazzmaster and Jaguar style guitars. Upgrade cheap or malfunctioning switches with these high quality replacements.

• Recommended .75 control cavity depth
• 1.125” center-to-center mounting hole spacing
• Screws not included
• See S-HS440-12 for compatible screws

Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount Features:

• SPDT ( Single Pole/ Double Throw) On-On switch
• 0.275" bushing length
• 0.270” bat length
• ¼" chassis hole diameter
• Right angle, PC Mount terminals

Note: On-On switches may sometimes be referred to as On-None-On.

1A, 250V; 3A, 125V. Carling SPDT 2 position toggle switch. Great Fender ground switch replacement.

High quality three position rotary switch commonly used as an impedance selector switch on tube amps. This rugged switch is rated for 6A at 125VAC and 3A at 250VAC. The flatted 6mm shaft can be used with the shaft adapter found in the accessories below to easily fit standard ¼” knobs. Mounting hardware included.

Chrome slotted nut for part S-HM301 toggle switch.

• Thread size = 15/32 - 32 thread pitch

Lighted power switch. Used in Marshall JCM series and others. 15/16" x 1-1/16" x 1" deep.

Genuine Switchcraft® DPTT 3-position slide switch for use on Mustang and Duosonic style guitars. This switch can be wired to operate in either On/Off/On or On/On/On configurations. Upgrade cheap or malfunctioning switches with these high quality replacements.

• Recommended .75 control cavity depth
• 1.406” center-to-center mounting hole spacing
• #4-40 screws recommended for mounting
• Screws not included

Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side.

Carling mini-toggle switch, SPDT, Solder Lug, 3-Position, On/Off/On

Carling mini-toggle switch, SPDT, PC Pins. 2-Position.

• 0.354" bushing length
• 2-Position On/On
• ¼" mounting hole diameter
• Single pole/Double throw (SPDT)
• PC mount pins

Original Marshall™. Black rocker switch for MG amps. 0.51" x 0.76" Mounting Hole. DPST.

Rotary impedance selector, 4/8/16. Body screws onto chassis hole.

Vintage style selector switch male part, replacement for Marshall.

For Marshall™, JCM series and others. 15/16" x 1 1/16" x 1" deep.

Threaded through dress nuts for use with mini toggle switches. Unlike the other versions of this dress nut, this nut is not capped allowing the nut to thread past the top of the switch’s bushing. The uncapped top can be useful where internal depth is an issue such as parallel PCB mounting. These plated dress nuts feature a chamfered edge for a professional look and work on any 1/4-40 UNS threaded bushing. Two sides are flatted for use with a tool when fastening.

Carling miniature rocker switch, DPST with .187" tabs (Marshall style). On-Off. 4A 250VAC; 8A 125VAC; 6A 250V. This switch is ideal for applications with back panel size constraints. It fits in a standard rectangular cutout and is designed to provide ease of insertion along with superior panel retention qualities. A high profile rocker and butt-action contacts provide the user with a crisp positive-type feel.