Switches

P-H600-A Switch - Rotary, 1 Pole, 3 Position
High quality three position rotary switch commonly used as an impedance selector switch on tube amps. This rugged switch is rated for 6A at 125VAC and 3A at 250VAC. The flatted 6mm shaft can be used with the shaft adapter found in the accessories below to easily fit standard ¼” knobs. Mounting hardware included. SP3T.
$12.95
P-H395 Switch - Rotary, 3 Poles, 3 Position
Rotary Switch, 3 Poles, 3 Positions (12 solder terminals), Make Before Break. 1/4 solid shaft Bushing width: 11/32" Bushing height: 5/16" Includes nut & washer 0.3A 125VAC. 3P3T rotary switch.
$2.55
P-H1700 Switch - Rotary, Impedance Selector, Replacement for Marshall
Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side. SP3T.
$34.95
On Backorder
P-H1701 Switch - Rotary, Impedance Selector, 3 Position
Rotary impedance selector, 4/8/16. Body screws onto chassis hole. SP3T switch.
$16.95
S-HM100-A Switch - Rotary, Voltage Selector, Modern, for Marshall
  • Ratings:
    • IEC: 6.3 A / 250 VAC; 50 Hz
    • UL: 10 A / 250 VAC; 60 Hz
    • CSA: 8 A / 250 VAC; 60 Hz
  • Mounting: Panel Mount from front side
  • Fastening: Screw-on mounting
  • Terminal: Solder
  • Number of Stages: 3
  • Type: SP3T
  • Lifetime: 300 operating cycles (without load)
  • Degree of Protection: IP 40
  • Allowable Operation Temp.: -40 °C to 85 °C
  • Climatic Category: 25/85/21 acc. to IEC 60068-1
  • Material of Socket: Thermoplastic, black, UL 94V-0
  • Weight: 16.5 g
  • Solderability: 350 °C / 2 sec acc. to IEC 60068-2-20, Test Ta, method 2
  • Resistance to Soldering Heat: 350 °C / 10 sec acc. to IEC 60068-2-20, Test Tb, method 2
  • Insulation Resistance: > 10,000MΩ (500VDC; 1min)
  • Contact Resistance: < 10 mΩ at 20 mV
  • Dielectric Strength:
    • > 2.5kVAC between L-N (1min; 50Hz)
    • > 4kVAC between L/N-PE (1min; 50Hz)
  • Clearance and Creepage Distance:
    • > 5mm
    • > 8mm between L/N-PE
  • Resistance to Vibration: acc. to IEC 60068-2-6, test Fc
$35.45
P-H1600-A Switch - Rotary Impedance Selector, for Hammond 1600A series
Includes: 3 pole, 3 position rotary switch (3P3T), 1/4" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with 1/4" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and 1/4" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
$11.95
Don't see what you're looking for? Send us your product suggestions!