Semiconductors

120V - 100W DMOS audio amplifier with mute/standby. The TDA7293 is a monolithic integrated circuit in Multiwatt15 package, intended for use as audio class AB amplifier in Hi-Fi field applications, such as home stereo, self powered loudspeakers and Topclass TV. Thanks to the wide voltage range and to the high output current capability it is able to supply the highest power into both 4-Ω and 8-Ω loads.

LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.

The BA4560, is a dual operational amplifiers which achieves approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. 8-pin DIP package.

LM741 single opamp in an 8-pin DIP package. The LM741 has been used in classic guitar pedals such as the Distortion Plus.
The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.

15 A, 60 V, 115 W
EPIBASE - Designed for power amplifier and switching regulator applications. The best choice where high frequency response, low switching losses and good safe operating area are required.

• Current Gain - Bandwidth Product - fT = 2.5 MHz (Min) @ Ic = 1.0 Adc
• Safe Operating Area - Full Power Rating to 40 V

Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.

The Spin Semiconductor FV-1 is a complete reverb solution in a single IC. With integrated stereo ADC and DACs, the FV-1 can be treated like any other analog component in your product's signal path. The FV-1 can access a total of 16 programs, 8 are built into the internal ROM and the designer may elect to connect a serial EEPROM with 8 additional programs. By using an external EEPROM, the designer can distinguish his product from others by creating a custom program set without the need for a microprocessor in the system. With 3 potentiometer inputs, programs may have real time variable parameters such as decay time in a reverb, rate and depth in a chorus or frequency in a filter. These inputs are available as coefficients to your program and may be used independently of each other. The rich instruction set allows users to program effects of all kinds. With instructions like LOG and EXP, users can easily program audio expansion and compression routines.

MPS 6531, NPN general purpose amp, 40V, TO-92 Case.

Low noise transistor for audio frequency amplifier applications.

MPS 6533, PNP general purpose amp, 40V, TO-92 Case.

High performance, ultrafast diodes. Improve efficiency, reduce noise, allow higher frequency operation.

Transistor MJ15015, TO-3 Case, NPN
PowerBase complementary transistors designed for high power audio, stepping motor and other linear applications. These devices can also be used in power switching circuits such as relay or solenoid drivers, dc–to–dc converters, inverters, or for inductive loads requiring higher safe operating areas.
Safe Operating Area - Rated to 60V

Transistor TIP42C, TO-220 Case.
PNP Epitaxial Silicon Transistor
Complementary to TIP41 (P-QTIP41C)
Max ratings:

• Collector-Base voltage = -100V
• Collector-Emitter Voltage = -100V
• Emitter-Base Voltage = -5V
• Collector current (DC) = -6A
• Collector current (Pulse) = -10A
• Base current = -2A

Dual wide-bandwidth LF353 opamps in an 8-pin DIP package. The LF353 offers a high input impedance and 3MHz bandwidth.
This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.

High performance, ultrafast diodes. Improve efficiency, reduce noise, allow higher frequency operation.

Alternistors are specifically designed for applications which are required to switch highly inductive loads. To accomplish this, a special chip has been designed which effectively offers the same performance as two thyristors (SCRs) wired inverse parallel (back to back); hence the alternistor has better turn-off behavior than a standard triac.

A semiconductor device that, above a certain reverse voltage(the zener value) has a sudden rise in current. If forward biased, the diode is an ordinary rectifier. When reverse biased, it exhibits a sharp break in its current-voltage graph. Voltage across the diode remains essentially constant for any further increase of reverse current.

Dual low power opamps in an 8-pin DIP package. The TL062 offers a high input impedance and 1MHz bandwidth.

Transistor MJ15016, TO-3 Case, PNP
PowerBase complementary transistors designed for high power audio, stepping motor and other linear applications. These devices can also be used in power switching circuits such as relay or solenoid drivers, dc–to–dc converters, inverters, or for inductive loads requiring higher safe operating areas.
Safe Operating Area - Rated to 60V

2N5400 (761), PNP general purpose amp, 120V, 10mA, TO-92 case.

High performance, ultrafast diodes. Improve efficiency, reduce noise, allow higher frequency operation.

SDS 7204, 300V, 10 mA, Case-30.

Transistor TIP41C, TO-220 Case. NPN Epitaxial Silicon Transistor Complementary to TIP42 (P-QTIP42C) Max ratings:

• Collector-Base voltage = 100V
• Collector-Emitter Voltage = 100V
• Emitter-Base Voltage = 5V
• Collector current (DC) = 6A
• Collector current (Pulse) = 10A
• Base current = 2A

DG212CJ, used in certain Marshall amplifiers. The DG212 are low cost quad single-pole single-throw analog switches for use in general purpose switching applications in communication, instrumentation and process control.