Semiconductors

VTL5C1 vactrols for use in amplifiers, effect pedals, synthesizers and more. The VTL5C1 was commonly used for channel switching circuits in amps made by Crate and others.

The TL072 is a high speed JFET input dual operational amplifier incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The device features high slew rates, low input bias and offset current, and low offset voltage temperature coefficient.

Dual Operational Amplifier. The 4558 integrated circuit is a dual high-gain operational amplifier internally compensated and constructed on a single silicon chip using an advanced epitaxial process. Combining the features of the NJM741 with the close parameter matching and tracking of a dual device on a monolithic chip results in unique performance characteristics. Excellent channel separation allows the use of the dual device in single NJM741 operational amplifier applications providing density. It is especially well suited for applications in differential-in, differential-out as well as in potentiometric amplifiers and where gain and phase matched channels are mandatory. Features:

• Operating Voltage (±4V~±18V)
• High Voltage Gain (100dB typ.)
• High Input Resistance (5MΩ typ.)
• Bipolar Technology

The 2N2222A is a NPN transistor in a TO-18 metal case. The 2N2222A is commonly used in fuzz pedals.

PT2399 echo/delay chip used in many DIY and commercial pedals. The PT2399 is in a DIP 16 package. Minimal external components are required for use and delay time is set with resistance.

General purpose low level, low noise amplifier. Silicon NPN transistor.

General purpose low-power NPN bipolar junction transistor, used frequently in hobbyist electronic projects.

This a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM1458, it shows better noise performance, improved output drive capability, and considerably higher small-signal and power bandwidths. it is compensated internally for voltage follower circuit. This makes the device especially suitable for application in high quality and professional audio equipment, instrumentation, control circuits, and telephone channel amplifiers Features:

• Operating Voltage = ±3V~±22V
• Small Signal Bandwidth = 10MHz typ.
• Output Drive Capability = 600Ω,10Vrms typ.
• Input Noise Voltage = 5nV/√Hz typ.
• Power Bandwidth = 140kHz typ.
• Slew Rate = 8V/µs typ.
• Bipolar Technology

SJE 5332, 120V, 3A, Case-77.

Low noise JFET quad operational amplifier. Incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. Features high slew rates, low input bias and offset currents, and low offset voltage temperature coefficients. Features:

• Wide common-mode and differential voltage range
• Low input bias and offset current
• Low noise en = 15 nV/HZ
• Output short-circuit protection
• High input impedance JFET input stage
• Low harmonic distortion: 0.01%
• Internal frequency compensation
• Latch up free operation
• High slew rate: 16 V/us (typical)

SJE 5331, 120V, 3A, Case-77.

120V - 100W DMOS audio amplifier with mute/standby. The TDA7293 is a monolithic integrated circuit in Multiwatt15 package, intended for use as audio class AB amplifier in Hi-Fi field applications, such as home stereo, self powered loudspeakers and Topclass TV. Thanks to the wide voltage range and to the high output current capability it is able to supply the highest power into both 4-Ω and 8-Ω loads.

LM741 single opamp in an 8-pin DIP package. The LM741 has been used in classic guitar pedals such as the Distortion Plus.
The LM741 series are general purpose operational amplifiers which feature improved performance over industry standards like the LM709. They are direct, plug-in replacements for the 709C, LM201, MC1439 and 748 in most applications. The amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, as well as freedom from oscillations.

15 A, 60 V, 115 W
EPIBASE - Designed for power amplifier and switching regulator applications. The best choice where high frequency response, low switching losses and good safe operating area are required.

• Current Gain - Bandwidth Product - fT = 2.5 MHz (Min) @ Ic = 1.0 Adc
• Safe Operating Area - Full Power Rating to 40 V

Low noise transistor for audio frequency amplifier applications.

LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.

Dual wide-bandwidth TL082 opamps in an 8-pin DIP package. The TL082 offers a high input impedance and 4MHz bandwidth.

Transistor MJ15015, TO-3 Case, NPN
PowerBase complementary transistors designed for high power audio, stepping motor and other linear applications. These devices can also be used in power switching circuits such as relay or solenoid drivers, dc–to–dc converters, inverters, or for inductive loads requiring higher safe operating areas.
Safe Operating Area - Rated to 60V

PC 1188H Power Amp - Fender The PC1188H is a monolithic integrated circuit and a power amplifier designed for Hi-Fi audio sets. The PC1188H can provide 20W (typical) to 8 ohms at 1% T.H.D. and +/- 22V supply voltage. Features:

• High output power
• Low distortion
• Wide frequency bandwidth
• A muting function which eliminates pop on noise and the thermal and the over current protection circuit

Transistor MJ15016, TO-3 Case, PNP
PowerBase complementary transistors designed for high power audio, stepping motor and other linear applications. These devices can also be used in power switching circuits such as relay or solenoid drivers, dc–to–dc converters, inverters, or for inductive loads requiring higher safe operating areas.
Safe Operating Area - Rated to 60V

Dual low power opamps in an 8-pin DIP package. The TL062 offers a high input impedance and 1MHz bandwidth.

The BA4560, is a dual operational amplifiers which achieves approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. 8-pin DIP package.

MPS 6531, NPN general purpose amp, 40V, TO-92 Case.

MPS 6533, PNP general purpose amp, 40V, TO-92 Case.