Radio & Antique Equipment Parts

Reliable replacement relay for the Leslie 122. The small size makes this high quality relay easy to retrofit in the 122. Its performance exceeds the original relays used in the Leslie 122 with its very low switching noise and high ratings on both the contacts and the coil.
Features:

• 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
• Coil EMC suppression
• Cadmium Free contact material

Replacement lower slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".

Cleans and revitalizes rubber, prolonging life and restoring function.

• Prolongs life of rubber parts
• Deglazes hardened rubber hoses, drive wheels and belts.
• Revitalizes rubber by removing buildup
• Restores the "gripping" surface
• Cleans and makes surfaces like new

High impedance crystal earphone - very sensitive and works great with crystal radios. Has 3 a foot cord and miniature (3.5 mm) plug.

Included in the Power-All System and also available separately, the Cable-Red/R allows the user to power effect units that have reverse polarity barrel connectors (tip positive/barrel negative). The Cable-Red/R features a tip positive, male barrel connector that is spring-loaded to prevent disconnection. The Cable-Red/R can be hooked to any plug on any of the Power-All daisy chains, or directly to the Power-All.

Lower slow motor rebuild kit for Leslie models 122/147. Includes installation instructions.

Small wire nuts, for use on appliances, televisions, stereos, antennas, or for any small wiring application.

GC Electronics 8606 alignment tool with hex and special tip slug. This tool is made of non-conductive Delrin.

• End 1 - 0.027 in.
• End 2 - 0.1 in.
• End 3 - 0.1 in.

Coil is similar to Miller number 70-OSC oscillator coil. Their small physical size and the fact that they can be adjusted to the inductance required make these coils ideally suited for replacement in broadcast band receivers. The 70 Oscillator coil has a primary and a tapped secondary. These coils are for use in all common padded and unpadded oscillator circuits.

Replacement rubber O ring for the Leslie 122 and 147 cabinets.

Contains

• 5009 Duplex no-metal screwdriver
• 5097 K-tran tool
• 8271 core aligner
• 8282 Zenith alignment tool
• 9091 hex iron core tool
• 9440 transistor tool
• 8276 Duplex aligner
• 9304 double end tool

Replacement upper drive belt for Leslie models 122 and 147. This belt is made of a high quality clear polyurethane that is both chemical and abrasion resistant ensuring a long life of use. This round belt had a 25.5 in. diameter with a sanded seam to ensure a smooth drive.

Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Overall dimensions 1 1/8" dia. x 1/4" thick.

Replacement upper belt tension spring for Leslies.

Contains 6 different tools for all standard adjustments. Tools are Delrin with the exception of the potentiometer adjustment tool which is Nylon.
Tools are:

• 8282 Zenith type Hex/Screwdriver
• 8606 5" Hex wrench
• 9091 Hex iron core tool
• 9300 5" Double sided hex tool
• 9304 Hex screwdriver combination
• 8608 Potentiometer Adjustment Tool

Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. Allows proper dial centering in cabinet opening. Overall dimensions 0.875" dia. x .233" thick.

Sealed lower rotor bearing for Leslies.

105°C temperature rating, 600V.

Rubber grommets for mounting phonograph motors. 1/2 dia. 5/16" high and ¼" inner dia.

6 pin female socket with wavy washer, for Leslies.

Designed to fit over unused male barrel connectors on a daisy chain or power supply, Cable-Caps protect against short circuits that can occur when a live lead touches a metal surface. Sold in sets of three. Fits over standard 5.5 mm diameter barrel plug connectors.

This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.

• Voltage: 9VDC
• Current: 200mA
• Tip positive; Sleeve negative

New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!

Replace deteriorated rubber parts in Leslie cabinets. Includes grommets, o-rings, bushings, plug.