Radio & Antique Equipment Parts

Inherent vibrations degrade the sound quality of your audio/video system. VIBRAPOD Isolators were designed to isolate your components from vibration in both the horizontal and vertical planes. VIBRAPOD Cones work best in the vertical plane, however when combined with VIBRAPOD Isolators they enhance isolation in the horizontal plane.

Will replace broadcast band coils in any tube type radio. Adjustable inductance for perfect tracking. Mount on bus wire leads or in 5/16" hole for pine board mounting. Coils are similar to Miller numbers that correspond.

• Primary coil inductance: 2mH
• Secondary coil inductance: 191uH

Input - 120V, 60 Hz. "A" Output - Adjustable and regulated 1.5 to 7.5 volts 1.5 Amps "B" Output - 22, 45, 67, 90, and 135 volts regulated up to 50mA. "C" Output - Adjustable 0 to 22 volts. Regulated. Kit includes transformer, rectifiers, capacitors, resistors, transistors, I.C., regulator, white pine board, and all necessary hardware. Easy to follow instructions for assembly.

Now your antique radio can play some of the same programs it did when it was new! With your cassette tape player, phonograph or high output microphone, this one tube transmitter becomes a miniature AM broadcasting station, patterned after the 1939 Zenith model S-7000 Wireless Record Player. Assemble on a 4 inch x 6.5 inch board. All parts and instructions included.

To order a schematic, enter the make and model of your schematic and click the Add to Cart button. Alternatively, you can browse our library of schematics online to find the schematic you're looking for. We have a vast library of schematics and if we have the one you are looking for we'll send it to you. If we do not have what you need, we'll contact you to let you know.

Coil is similar to Miller number 70-OSC oscillator coil. Their small physical size and the fact that they can be adjusted to the inductance required make these coils ideally suited for replacement in broadcast band receivers. The 70 Oscillator coil has a primary and a tapped secondary. These coils are for use in all common padded and unpadded oscillator circuits.

Coil is similar to Miller number 70-RF. Coil is similar to Miller number 70-RF R.F. stage coil. Their small physical size and the fact that they can be adjusted to the inductance required make these coils ideally suited for replacement in broadcast band receivers. The R.F. coils have high impedance primaries and wire wound secondaries for use with any variable condenser having a maximum capacity between 250 and 450 mmf. These coils are for use in all common padded and unpadded oscillator circuits.

Reproduction paper station inserts like used on Philco and other late 30s and 40s vintage radios with bush-button tuning. Over 300 stations privided with 3/16 high letters in translucent ivory color on black background. Trim to size to fit various models.

Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Overall dimensions 1 1/8" dia. x 1/4" thick.

Assortment of knob springs for 1/2 moon shaft. 3/8" high x 9/32" outside dia. "D" shaped package of 6.

Rubber grommets for mounting phonograph motors. 1/2 dia. 5/16" high and ¼" inner dia.

Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features

• Primary: 4000 turns, #41 wire (lugs 4 & 2)
• Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
• Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
• Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
• Lamination Core Size: 5/8" x 1/2"
• Weight: 7 oz.

New manufacture solid-state replacement 4 pin vibrators. These replace our old line of solid state vibrators. 1-1/2 dia. x 2-¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!

New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!

A quick-drying, waterproof clear adhesive which forms a strong, hard, water and vibration-resistant bond with minimal shrinkage. Ideal for speaker repairs and bonding semi-porus materials to each other or to metals, plastics, etc. 2 oz. bottle. Can be used as a glue for small speaker cone repairs.

Removes scratches from acrylic surfaces; significantly reduces haziness. More abrasive than Novus #2 and is effective for deeper scratches. Treatment should be followed by Novus #2 to buff and polish surface.

Cleans and glazes plastic surface polish out and protect against small scratches, finger markings, dust build-up, and other markings. Significantly reduces haziness and is anti-static.

Removes fine scratches, abrasions and haziness from plastic surfaces. Great for plastic radio dial windows. For best results, follow with Novus No. 1 polish.

Cleans and revitalizes rubber, prolonging life and restoring function.

• Prolongs life of rubber parts
• Deglazes hardened rubber hoses, drive wheels and belts.
• Revitalizes rubber by removing buildup
• Restores the "gripping" surface
• Cleans and makes surfaces like new

Uses current from any 3 to 6 volt D.C. supply or batteries. Plating brush connects to positive voltage and part being plated connects to negative. Brush (S-F225) sold separately.
Available in multiple materials.

Electroplating brush used for replating nickel, silver or brass radio and phonograph parts. Uses current from any 3 to 6 volt DC supply supply or batteries. Plating brush connects to positive voltage and part being plated connects to negative. Instructions included. Electroplating compound sold separately. Uses current from any 3 to 6 volt D.C. supply or batteries. Plating brush connects to positive voltage and part being plated connects to negative. Electroplating Compound (S-F222X) sold separately.

Paint compatible for use with grey wrinkle finish to make brown wrinkle finish.
Postal regulations prohibit shipping aerosol cans outside the continental U.S.

Spring clip ¾" long for up to 15 ga. wire. Hole fits U.S. Screw size # 6. Package of 6.

Use as a standoff, coil/choke form, or antenna coil.