Radio & Antique Equipment Parts

K-101A Kit - Pine Board Power Supply with 3 Outputs
Input - 120V, 60 Hz. "A" Output - Adjustable and regulated 1.5 to 7.5 volts 1.5 Amps "B" Output - 22, 45, 67, 90, and 135 volts regulated up to 50mA. "C" Output - Adjustable 0 to 22 volts. Regulated. Kit includes transformer, rectifiers, capacitors, resistors, transistors, I.C., regulator, white pine board, and all necessary hardware. Easy to follow instructions for assembly.
$64.95
P-OH-101 Motor Assembly - Upper Slow, for Leslie 122/147
Replacement upper slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".
$63.95
P-OH-102 Motor Assembly - Lower Slow, for Leslie 122/147
Replacement lower slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".
$63.95
P-OH-509 Grommet Kit - All Rubber Parts, for Leslie
Package of 33
Replace deteriorated rubber parts in Leslie cabinets. Includes grommets, o-rings, bushings, plug.
$61.25
P-OH-401 Relay - SPDT, 110VDC, for Leslie 122
Replacement relay for Leslie Model 122, 110 VDC, 5 K , SPDT. The contacts are rated at 10A.
$35.95
P-V1015X Vibrator - 4 Pin, for automobile radio
New manufacture solid-state replacement 4 pin vibrators. These replace our old line of solid state vibrators. 1-1/2 dia. x 2-¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
P-V2215N Vibrator - 12 Volt, 3 Pin, Negative Ground
New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
$34.95
P-OH-402 Relay - 115 Volt AC, for Leslie 147
Replacement relay for Leslie model 147 amplifier, 115 VAC , SPDT. The contacts are rated at 10A.
$32.50
S-W102-X Wire - 18 Gauge, 2 conductor, braided Power Cord
Brown 2 conductor 18 gauge, stranded power cord, similar to woven cloth covered cords in early AC radios. 105°C temperature rating, 600V.
Starting at $25.00
S-VIBRAX-4 Vibrapod Isolator - Isolate Components
Package of 4
Inherent vibrations degrade the sound quality of your audio/video system. VIBRAPOD Isolators were designed to isolate your components from vibration in both the horizontal and vertical planes. VIBRAPOD Cones work best in the vertical plane, however when combined with VIBRAPOD Isolators they enhance isolation in the horizontal plane.
$25.00
M-PAS-X Power Supply - Power All System, For Effects Pedals
The Power-All PA-9 Digital Power Supply is the world’s first 2,000 mA, single outlet power supply designed specifically for guitar effect users. Don’t waste money on batteries or take up valuable space with multiple “wall wart” adaptors or power bricks – the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All provides 9 volts DC at 2,000 milliamps – more than enough current to power dozens of effect pedals, including up to four Line 6 Modelers! The Power-All’s special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9 now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.
Starting at $24.95
M-PAS-S Power Supply - Power All System, 9V, 2000mA, for Effects Pedals
The PA-9 Power-All is the world's first 2000 mA, single outlet power supply designed specifically for guitar effect users. Don't waste money on batteries or take up valuable space with multiple "wall wart" adaptors or power bricks - the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All's special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9S now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.
$19.95
P-OH-302 Belt - Leslie, 31", Lower Drive, for 122/147
Replacement lower drive belt, white, 31" circumference.
$19.45
P-OH-301 Belt - Leslie, Upper Drive, 25.5", for 122/147
Replacement upper drive belt , 25.5" circumference
$18.95
On Backorder
P-OH-502 Rotor Cover - 17", for Leslie 122/147
17" rotor cover fits Leslie models 122/147.
$18.75
S-T18-530 Alignment Kit - GC Electronics, for CB
Package of 8
Contains
  • 5009 Duplex no-metal screwdriver
  • 5097 K-tran tool
  • 8271 core aligner
  • 8282 Zenith alignment tool
  • 9091 hex iron core tool
  • 9440 transistor tool
  • 8276 Duplex aligner
  • 9304 double end tool
$18.50
On Backorder
S-F222X Electroplating Compound - for metal coating
Uses current from any 3 to 6 volt D.C. supply or batteries. Plating brush connects to positive voltage and part being plated connects to negative. Brush not included. Available in multiple materials.
Starting at $17.95
M-PAS-CABLE-2 Cable - Power All, 11 Lead Right Angle Daisy Chain
Designed for larger pedalboards, the Power-All Cable-11/R Daisy Chain features ELEVEN right-angle male barrel plugs with spring loaded jacks for extra secure connections – no more losing power mid-solo! 28-gauge cable with oil-resistant sheath and 10-inch cable length between plugs allows connection of larger and odd-sized pedals.
$15.00
P-C70-OSC Coil - Miniature adjustable coil, 70, oscillator
Coil is similar to Miller number 70-OSC oscillator coil. Their small physical size and the fact that they can be adjusted to the inductance required make these coils ideally suited for replacement in broadcast band receivers. The 70 Oscillator coil has a primary and a tapped secondary. These coils are for use in all common padded and unpadded oscillator circuits.
$14.95
P-ECB-002 Power Supply - Dunlop, 9V, 200mA, 3.5mm Positive Tip
This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.
  • Voltage: 9VDC
  • Current: 200mA
  • Tip positive; Sleeve negative
$12.50
P-ECB-003 Power Supply - Dunlop, 9V, 200mA, Barrel, Center Negative

Dunlop ECB003 US wallwart power supply. Barrel connector.

  • Voltage: 9VDC
  • Current: 200mA
  • Tip Negative; Sleeve positive
$12.50
P-OH-503 Spring - Leslie, Tension, for Upper Belt
Replacement upper belt tension spring for Leslies.
$12.50
P-OH-505 Bearing - Leslie, Lower Rotor, sealed
Sealed lower rotor bearing for Leslies.
$10.99
S-W7XL Wire - 20 AWG Stranded Core, Lacquered Cloth Cover, 600V
Colors Available:
#20 stranded copper wire with modern insulation and lacquered cotton braid finish. Provides safety and authentic vintage look.
105°C temperature rating, 600V.
Solid Core: S-W8XL
Starting at $9.00
Don't see what you're looking for? Send us your product suggestions!