Radio & Antique Equipment Parts

Replacement upper slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".
$89.95

Replacement lower slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".
$89.95

This is a set of measured vacuum tubes for use in TV-7 vacuum tube tester calibration. The values for each vacuum tube will be measured and included for the purpose of calibrating your own TV-7 tester at home. Steps for this calibration can be found online. Three tubes will be included:
These tubes are tested at the following settings: Tube Filament Settings Bias Shunt Range 6L6 6.3 HS5-3481 23 0 D Tube Filament Settings Bias Shunt Range 6AU6 6.3 ET1-5672 16 0 B Tube Filament Settings Bias Shunt Range 12AT7 12.6 EV7-6080 10 0 C Note that brands are not guaranteed to match photograph.
- 6L6
- 6AU6
- 12AT7
These tubes are tested at the following settings: Tube Filament Settings Bias Shunt Range 6L6 6.3 HS5-3481 23 0 D Tube Filament Settings Bias Shunt Range 6AU6 6.3 ET1-5672 16 0 B Tube Filament Settings Bias Shunt Range 12AT7 12.6 EV7-6080 10 0 C Note that brands are not guaranteed to match photograph.
$75.00

Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features
Key Features
- Primary: 4000 turns, #41 wire (lugs 4 & 2)
- Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
- Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
- Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
- Lamination Core Size: 5/8" x 1/2"
- Weight: 7 oz.
$67.70

Package of 33
Replace deteriorated rubber parts in Leslie cabinets. Includes grommets, o-rings, bushings, plug.
$49.95

New manufacture solid-state replacement 4 pin vibrators. These replace our old line of solid state vibrators. 1-1/2 dia. x 2-¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
Starting at $34.95

New manufacture solid-state replacements for 12 volt, 3 pin vibrators with a negative ground. These replace our old line of solid state vibrators. 1 1/2 dia. x 2 ¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!
$34.95

6 pin female socket with wavy washer, for Leslies.
$34.25

Reliable replacement relay for the Leslie 122. The small size makes this high quality relay easy to retrofit in the 122. Its performance exceeds the original relays used in the Leslie 122 with its very low switching noise and high ratings on both the contacts and the coil.
Features:
Features:
- 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
- Coil EMC suppression
- Cadmium Free contact material
$32.95

Reliable replacement relay for the Leslie 147. The small size makes this high quality relay easy to retrofit in the 147. Its performance exceeds the original relays used in the Leslie 147 with its very low switching noise and high ratings on both the contacts and the coil. Features:
- 8 mm, 6 kV (1.2/50 µs) isolation, coil-contacts
- Coil EMC suppression
- Cadmium Free contact material
$32.50

Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects. Power-All® kits include a variety of useful cables for powering multiple pedals to the ECO-Dapter® 9V supply.
Starting at $30.95

Switch for run circuit in Hammond Organ. Electrical Rating: 16 A - 125 V 8 A - 250 V Dimensions: Mounting Diameter: ½" Bushing Length: 0.425" Length: 1.89" Width: 0.82" Depth: 0.69"
$29.95

Brown 2 conductor 18 gauge, stranded power cord, similar to woven cloth covered cords in early AC radios. 105°C temperature rating, 600V.
Starting at $26.75

Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects.
$24.35

Package of 8
Contains- 5009 Duplex no-metal screwdriver
- 5097 K-tran tool
- 8271 core aligner
- 8282 Zenith alignment tool
- 9091 hex iron core tool
- 9440 transistor tool
- 8276 Duplex aligner
- 9304 double end tool
$20.35

17" diameter rotor cover fits Leslie models 122/147. 13" in height. Replace torn or missing rotor covers.
$19.50

Replacement lower drive belt for Leslie models 122 and 147. This belt is made of a high quality clear polyurethane that is both chemical and abrasion resistant ensuring a long life of use. This round belt had a 31 in. diameter with a sanded seam to ensure a smooth drive.
$17.95

Designed for larger pedalboards, the Power-All Cable-11/R Daisy Chain features ELEVEN right-angle male barrel plugs with spring loaded jacks for extra secure connections – no more losing power mid-solo! 28-gauge cable with oil-resistant sheath and 10-inch cable length between plugs allows connection of larger and odd-sized pedals.
$16.25

Plug cover kit for Leslie , screws included. This is the connector cap for the connecting cable.
$15.55

Replacement upper drive belt for Leslie models 122 and 147. This belt is made of a high quality rubber that is both chemical and abrasion resistant ensuring a long life of use. This round belt had a 25.5 in. diameter with no seam to ensure a smooth drive.
$14.50

Dunlop ECB003 US wallwart power supply. Barrel connector.
- Voltage: 9VDC
- Current: 200mA
- Tip Negative; Sleeve positive
$12.70