Radio & Antique Equipment Parts

Butyrate shaft 6-1/8" long with 1/8" wide steel tips. Tip on one end recessed.

• Material: Conductive Nylon Metal
• End: 1/8"
• End 2: 1/8"

Contains

• 5009 Duplex no-metal screwdriver
• 5097 K-tran tool
• 8271 core aligner
• 8282 Zenith alignment tool
• 9091 hex iron core tool
• 9440 transistor tool
• 8276 Duplex aligner
• 9304 double end tool

Contains 6 different tools for all standard adjustments. Tools are Delrin with the exception of the potentiometer adjustment tool which is Nylon.
Tools are:

• 8282 Zenith type Hex/Screwdriver
• 8606 5" Hex wrench
• 9091 Hex iron core tool
• 9300 5" Double sided hex tool
• 9304 Hex screwdriver combination
• 8608 Potentiometer Adjustment Tool

Sealed lower rotor bearing for Leslies.

Sealed upper tension idler bearing for Leslies

Replacement lower drive belt, white, 31" circumference.

Replacement upper drive belt , 25.5" circumference

A quick-drying, waterproof clear adhesive which forms a strong, hard, water and vibration-resistant bond with minimal shrinkage. Ideal for speaker repairs and bonding semi-porus materials to each other or to metals, plastics, etc. 2 oz. bottle. Can be used as a glue for small speaker cone repairs.

Cleans and revitalizes rubber, prolonging life and restoring function.

• Prolongs life of rubber parts
• Deglazes hardened rubber hoses, drive wheels and belts.
• Revitalizes rubber by removing buildup
• Restores the "gripping" surface
• Cleans and makes surfaces like new

Coil is similar to Miller number 70-OSC oscillator coil. Their small physical size and the fact that they can be adjusted to the inductance required make these coils ideally suited for replacement in broadcast band receivers. The 70 Oscillator coil has a primary and a tapped secondary. These coils are for use in all common padded and unpadded oscillator circuits.

Coil is similar to Miller number 70-RF. Coil is similar to Miller number 70-RF R.F. stage coil. Their small physical size and the fact that they can be adjusted to the inductance required make these coils ideally suited for replacement in broadcast band receivers. The R.F. coils have high impedance primaries and wire wound secondaries for use with any variable condenser having a maximum capacity between 250 and 450 mmf. These coils are for use in all common padded and unpadded oscillator circuits.

Water slide decal (not a sticker). Emerson treble-clef logo is gold with black outline, in 2 common sizes.

No stretch black cord made of nylon braid over a fiberglass core. Standard thin, 0.028 diameter. Sold by the foot.

The 1N34A Germanium diode is an old standby in electronics. Widely used for detecting the rectifying efficiency or for switching on a radio, TV or stereo etc.

High impedance crystal earphone - very sensitive and works great with crystal radios. Has 3 a foot cord and miniature (3.5 mm) plug.

Uses current from any 3 to 6 volt D.C. supply or batteries. Plating brush connects to positive voltage and part being plated connects to negative. Brush (S-F225) sold separately.
Available in multiple materials.

Spring clip ¾" long for up to 15 ga. wire. Hole fits U.S. Screw size # 6.

Use as a standoff, coil/choke form, or antenna coil.

Rubber grommets for mounting phonograph motors. 1/2 dia. 5/16" high and ¼" inner dia.

Replace deteriorated rubber parts in Leslie cabinets. Includes grommets, o-rings, bushings, plug.

Input - 120V, 60 Hz. "A" Output - Adjustable and regulated 1.5 to 7.5 volts 1.5 Amps "B" Output - 22, 45, 67, 90, and 135 volts regulated up to 50mA. "C" Output - Adjustable 0 to 22 volts. Regulated. Kit includes transformer, rectifiers, capacitors, resistors, transistors, I.C., regulator, white pine board, and all necessary hardware. Easy to follow instructions for assembly.

Now your antique radio can play some of the same programs it did when it was new! With your cassette tape player, phonograph or high output microphone, this one tube transmitter becomes a miniature AM broadcasting station, patterned after the 1939 Zenith model S-7000 Wireless Record Player. Assemble on a 4 inch x 6.5 inch board. All parts and instructions included.

Assortment of knob springs for 1/2 moon shaft. 3/8" high x 9/32" outside dia. "D" shaped package of 6.

Replacement lower slow motor assembly for Leslie models 122/147. Overall shaft length is 2.75".